| 1. |
-
INNOTRACK: Concluding technical report
- 2010
-
Samlingsverk (redaktörskap) (refereegranskat)abstract
- The track structure, rails, switches and crossings account for more than 50% of maintenance and renewal costs for the rail industry. To improve the competitiveness of rail transportation, the cost-efficiency of these areas needs to be addressed.This the background to INNOTRACK, an integrated research project funded by the European Commission’s 6th research framework pro- gramme. Running from September 2006 to December 2009, INN- OTRACK has developed a multitude of innovative solutions in the areas of track substructure, rails & welds, and switches & crossings. The solutions have been assessed from technical, logistics and life cycle cost point of views.This Concluding Technical Report of INNOTRACK includes an overview of the project. It further details implementable results, and clusters them into ”highlight” areas. In addition, the book acts as a ”key” to the vast amount of information from INNOTRACK: All sections refer to project reports where more information can be found.
|
|
| 2. |
|
|
| 3. |
- Bengtsson, Stefan, 1961, et al.
(författare)
-
Carbon-based nanoelectromechanical devices
- 2011
-
Ingår i: International Journal of High Speed Electronics and Systems. - 1793-6438. ; 20:1, s. 195-204
-
Tidskriftsartikel (refereegranskat)abstract
- Carbon-based nanoelectromechanical devices are approaching applications in electronics. Switches based on individual carbon nanotubes deliver record low off-state leakage currents. Arrays of vertically aligned carbon nanotubes or nanofibers can be fabricated to constitute varactors. Very porous, low density arrays of quasi-vertically aligned arrays of carbon nanotubes behave mechanically as a single unit with very unusual material properties.
|
|
| 4. |
- Jahanmiri, Mohsen, 1953
(författare)
-
Pressure Sensitive Paints:The Basics & Applications
- 2011
-
Rapport (övrigt vetenskapligt/konstnärligt)abstract
- Surface pressure measurement is one of the fundamental measurements in fluid dynamics experiments. Pressure sensitive paint (PSP) is a relatively new tool that has the unique capability of providing a field measurement over the entire surface of a model. This method is based on the attenuation by oxygen of the luminescence emitted by certain excited molecules in the visible or ultraviolet spectrums. The higher the pressure, the higher the partial pressure of the oxygen and the more the intensity emitted by the coating is attenuated. Then all that is needed is to measure the intensity of the emission to find the pressure. Because of its many advantages over the traditional techniques, it has been extensively used in almost all the fluid dynamics flow regimes. The following document describes the basics of PSP and its applications.
|
|
| 5. |
- Belitsky, Victor, 1955, et al.
(författare)
-
Towards Multi-Pixel Heterodyne Terahertz Receivers
- 2011
-
Ingår i: Proceedings of the 22nd International Symposium on Space Terahertz Technology, Tucson, AZ, USA, April 26-28, 2011. ; , s. 1-3
-
Konferensbidrag (refereegranskat)abstract
- Terahertz multi-pixel heterodyne receivers introduce multiple challenges for their implementation, mostly due to the extremely small dimensions of all components and even smaller tolerances in terms of alignment, linear dimensions and waveguide component surface quality. In this manuscript, we present a concept of terahertz multi-pixel heterodyne receiver employing optical layout using polarization split between the LO and RF. The frontend is based on a waveguide balanced HEB mixer for the frequency band 1.6 – 2.0 THz. The balanced HEB mixer follows the layout of earlier demonstrated APEX T2 mixer. However for the mixer presented here, we implemented splitblock layout offering minimized lengths of all waveguides and thus reducing the associated RF loss. The micromachining methods employed for producing the mixer housing and the HEB mixer chip are very suitable for producing multiple structures and hence are in-line with requirements of multi-pixel receiver technology. The demonstrated relatively simple mounting of the mixer chip with self-aligning should greatly facilitate the integration of such multi-channel receiver.
|
|
| 6. |
- Mill, O., et al.
(författare)
-
Analysis and development of hydro power research : synthesis within Swedish Hydro Power Centre
- 2010
-
Rapport (övrigt vetenskapligt/konstnärligt)abstract
- The market for hydropower re-investments in Sweden is approx 2.5 billion SEK/yr the coming decade. Large investments will also be carried out in Swedish tailing dams. This will result in challenging projects and need of experts. A crucial factor for a successful management of these challenges is the supply of engineers and researchers with hydro power and dam skills and knowledge. Swedish Hydro Power Centre (Svenskt vattenkraftcentrum, SVC) is a competence centre for university education and research environments within hydro power and mining dams. SVC comprises of two knowledge areas: Hydraulic Engineering and Hydro Turbines and Generators, respectively. SVC builds high-quality and long term sustainable knowledge at selected universities...
|
|
| 7. |
- Sandberg, David, 1980, et al.
(författare)
-
Detecting driver sleeepiness using optimized non-linear combinations of sleepiness indicators
- 2011
-
Ingår i: IEEE Transactions on Intelligent Transportation Systems. - 1524-9050 .- 1558-0016. ; 12:1, s. 97-108
-
Tidskriftsartikel (refereegranskat)abstract
- This paper addresses the problem of detecting sleepiness in car drivers. First, a variety of sleepiness indicators (based on driving behavior) proposed in the literature were evaluated. These indicators were then subjected to parametric optimization using stochastic optimization methods. To improve performance, the functional form of some of the indicators was generalized before optimization. Next, using a neural network, the best performing sleepiness indicators were combined with a mathematical model of sleepiness, i.e., the sleep/wake predictor (SWP). The analyses were based on data obtained from a study that involved 12 test subjects at the moving-base driving simulator at the Swedish National Road and Transportation Research Institute (VTI), Linkping, Sweden. The data were derived from 12 1-h driving sessions for each test subject, with varying degrees of sleepiness. The performance measure (range [0,1]) for indicators was taken as the average of sensitivity and specificity. Starting with indicators proposed in the literature, the best such indicator, i.e., the standard deviation of the yaw angle, reached a performance score of 0.72 on previously unseen test data. It was found that indicators based on a given signal gave essentially equal performance after parametric optimization, but in no case was it better than 0.72. The best generalized indicator (the generic variability indicator) obtained a performance score of 0.74. SWP achieved a score of 0.78. However, by nonlinearly combining SWP with the generic variability indicator, a score of 0.83 was obtained. Thus, the results imply that a nonlinear combination of a measure based on driving behavior with a model of sleepiness significantly improves driver sleepiness detection.
|
|
| 8. |
- Andersen, Maj Munch, et al.
(författare)
-
Green Nanotechnology in Nordic Construction: Eco-innovation Strategies and Dynamics in Nordic Window Value Chains
- 2010
-
Rapport (övrigt vetenskapligt/konstnärligt)abstract
- This project analyzes Nordic trends in the development and industrial uptake of green nanotechno-logy in construction. The project applies an evolutionary economic perspective in analyzing the innovation dynamics and firm strategies in the window value chains in three Nordic countries, Denmark, Finland and Sweden. Hence the project investigates two pervasive parallel market trends: The emergence of the green market and the emergence of nanotechnology. The analysis investigates how a traditional economic sector such as the construction sector reacts to such major trends.Conclusions are multiple, but among the most important are: Eco-innovation has become the perhaps most important driver for innovation in the construction sector. Search into eco-innovative business opportunities is intense among all companies along the three analyzed Nordic window chains. While we generally find a low uptake of nanotechnology in the construction sector in the Nordic countries we do find quite a high number of nanotech applications in the Nordic window chains. Eco-innovation is influencing strongly on the nanotech development. We see several examples of nano-enabled smart, multifunctional green solutions in the Nordic window chains already or about to having a commercial impact. Currently, it seems the greening of markets is beginning to affect the roles different companies play in the chain. We see a marked shift towards more sys-temic, smart eco-innovative solutions which fit well with nanotech opportunities. Overall, the recent greening of the market seems to be opening a window of opportunity for nanotechnology in the Nordic countries but the widespread discreet firm strategizing towards nanotechnology may reduce the exploitation of these.
|
|
| 9. |
- Cho, Sung-Woo, et al.
(författare)
-
Injection-molded nanocomposites and materials based on wheat gluten
- 2011
-
Ingår i: International Journal of Biological Macromolecules. - : Elsevier BV. - 0141-8130 .- 1879-0003. ; 48:1, s. 146-152
-
Tidskriftsartikel (refereegranskat)abstract
- This is, to our knowledge, the first study of the injection molding of materials where wheat gluten (WG) is the main component. In addition to a plasticizer (glycerol), 5 wt.% natural montmorillonite clay was added. X-ray indicated intercalated clay and transmission electron microscopy indicated locally good clay platelet dispersion. Prior to feeding into the injection molder, the material was first compression molded into plates and pelletized. The filling of the circular mold via the central gate was characterized by a divergent flow yielding, in general, a stronger and stiffer material in the circumferential direction. It was observed that 20–30 wt.% glycerol yielded the best combination of processability and mechanical properties. The clay yielded improved processability, plate homogeneity and tensile stiffness. IR spectroscopy and protein solubility indicated that the injection molding process yielded a highly aggregated structure. The overall conclusion was that injection molding is a very promising method for producing WG objects.
|
|
| 10. |
|
|
