| 1. |
- Appelgren, Patrik, et al.
(författare)
-
Experimental Study of Electromagnetic Effects on Solid Copper Jets
- 2010
-
Ingår i: Journal of applied mechanics. - : ASME International. - 0021-8936 .- 1528-9036. ; 77:1, s. 011010-
-
Tidskriftsartikel (refereegranskat)abstract
- In this paper we present a study of the interaction between all electric current pulse and a solid copper jet. Experiments were performed using a dedicated pulsed power supply delivering a current pulse of such amplitude, rise little, and duration that the jet is efficiently affected. The copper jet was created by using a shaped charge warhead. All electrode configuration consisting of two aluminum plates with a separation distance of 150 mm was used. The discharge current pulse and the voltages at the capacitors and at the electrodes were measured to obtain data oil energy deposition in and the resistance of the jet and electrode contact region. X-ray diagnostics were used to radiograph the jet, and by analyzing the radiograph, the degree of disruption of the electrified jet could be obtained. It was found that a current pulse with an amplitude of 200-250 kA and a rise time of 16 mu s could strongly enhance the natural fragmentation of the jet. In this case, the initial electric energy was 100 kJ and about 90% of the electric energy was deposited in the jet and electrodes. At the exit of the electrode region, the jet fragments formed rings with a radial velocity of up to 200 m/s, depending oil the initial electric energy in the pulsed power supply. [DOI: 10.1115/1.3172251]
|
|
| 2. |
- Appelgren, Patrik, et al.
(författare)
-
Interaction between solid copper jets and powerful electrical current pulses
- 2011
-
Ingår i: Journal of applied mechanics. - : ASME International. - 0021-8936 .- 1528-9036. ; 78:2
-
Tidskriftsartikel (refereegranskat)abstract
- The interaction between a solid copper jet and an electric current pulse is studied. Copper jets that were created by a shaped-charge device were passed through an electrode configuration consisting of two aluminum plates with a separation distance of 150 mm. The electrodes were connected to a pulsed-power supply delivering a current pulse with amplitudes up to 250 kA. The current and voltages were measured, providing data on energy deposition in the jet and electrode contact region, and flash X-ray diagnostics were used to depict the jet during and after electrification. The shape of, and the velocity distributions along, the jet has been used to estimate the correlation between the jet mass flow through the electrodes and the electrical energy deposition. On average, 2.8 kJ/g was deposited in the jet and electrode region, which is sufficient to bring the jet up to the boiling point. A model based on the assumption of a homogenous current flow through the jet between the electrodes underestimates the energy deposition and the jet resistance by a factor 5 compared with the experiments, indicating a more complex current flow through the jet. The experimental results indicate the following mechanism for the enhancement of jet breakup. When electrified, the natural-formed necks in the jet are subjected to a higher current density compared with other parts of the jet. The higher current density results in a stronger heating and a stronger magnetic pinch force. Eventually, the jet material in the neck is evaporated and explodes electrically, resulting in a radial ejection of vaporized jet material.
|
|
| 3. |
- Appelgren, Patrik, et al.
(författare)
-
Modeling of a small helical magnetic flux compression generator
- 2008
-
Ingår i: IEEE Transactions on Plasma Science. - 0093-3813 .- 1939-9375. ; 36:5, s. 2662-2672
-
Tidskriftsartikel (refereegranskat)abstract
- In order to gain experience in explosive pulsed power and to provide experimental data as the basis for computer modeling, a small high-explosive-driven helical magnetic flux-compression generator (FCG) was designed at the Swedish Defence Research Agency. The generator, of which three have been built, has an overall length of 300 mm and a diameter of 70 mm. It could serve as the energy source in a pulse-forming network to generate high-power pulses for various loads. This paper presents a simulation model of this helical FCG. The model, which was implemented in Matlab-Simulink, uses analytical expressions for the generator inductance. The model of resistive losses takes into account the heating of the conductors and the diffusion of the magnetic field into the conductors. The simulation results are compared with experimental data from two experiments with identical generators but with different seed currents, influencing the resistive losses. The model is used to analyze the performance of the generator.
|
|
| 4. |
- Appelgren, Patrik, et al.
(författare)
-
Small Helical Magnetic Flux-Compression Generators : Experiments and Analysis
- 2008
-
Ingår i: IEEE Transactions on Plasma Science. - 0093-3813 .- 1939-9375. ; 36:5, s. 2673-2683
-
Tidskriftsartikel (refereegranskat)abstract
- In order to gain experience in explosive pulsed power and to provide experimental data for modeling, a small high-explosive-driven helical magnetic flux-compression generator (FCG) was designed at the Swedish Defence Research Agency (FOI). The generator, of which three have been built, has an overall length of 300 mm and a diameter of 70 mm. It could serve as the energy source in a pulse-forming network to generate high power pulses for various loads. This paper presents the design of, and tests with, this helical FCG. The generator had an initial inductance of 23 mu H and was operated into a load of 0.2 mu H. The generator is charged with 0.27 kg of high explosives (PBXN-5). Various types of diagnostics were used to monitor the operation of the generator, including current probes, optical fibers, and piezo gauges. With seed currents of 5.7 and 11.2 kA, final currents of 269 and 436 kA were obtained, corresponding to current amplification factors of 47 and 39. The peak of the current was reached about 30 mu s after the time of crowbar. The two generators showed only small losses in terms of 2 pi-clocking. Using signals from optical fibers, the deflection angle of the armature could be determined to be 10 degrees in good agreement with hydrodynamic simulations of the detonation process and the detonation velocity to be 8.7 km/s in agreement with tabulated value.
|
|
| 5. |
- Elfsberg, Mattias, et al.
(författare)
-
Experimental Studies of Anode and Cathode Materials in a Repetitive Driven Axial Vircator
- 2008
-
Ingår i: IEEE Transactions on Plasma Science. - 0093-3813 .- 1939-9375. ; 36, s. 688-693
-
Tidskriftsartikel (refereegranskat)abstract
- Repetitive use of a high-power microwave (HPM) radiation source implies strong erosion on cathode and anode materials. Electrode material endurance has been studied in a series of experiments with an axial vircator powered by a compact Marx generator. The Marx generator operated in a 10 Hz repetitive mode with a burst of ten pulses. Velvet and graphite was used as electron-emitting materials, and they showed markedly different pulse characteristics. Three different anode materials were used; stainless steel mesh, stainless steel wires and molybdenum wires, which all had different influence on the pulse characteristics.
|
|
| 6. |
- Appelgren, Patrik, et al.
(författare)
-
Disruption mechanisms in electrified solid copper jets
- 2011
-
Ingår i: Journal of applied mechanics. - : ASME International. - 0021-8936 .- 1528-9036. ; 78:2
-
Tidskriftsartikel (refereegranskat)abstract
- Interaction between a solid copper jet and an electric current pulse is a complex process that has been experimentally studied by letting a jet created by a shaped charge device pass through an electrode configuration consisting of two aluminum plates with a separation distance of 150 mm. When the jet bridged the electrodes, which are connected to a charged pulsed power supply, current pulses with amplitude up to 250 kA were passed through the jet. By using flash X-ray diagnostics, the disruption of the electrified jets could be studied. In this paper, the disruption of the electrified jets is discussed and compared with disruption phenomena observed in electrically exploded metal rods in a static setup. Necks are naturally formed along a stretching jet, and in the experiments with current interaction these necks explode electrically. In the static experiments, the metal rods have small notches distributed along the rod to resemble the necks of the jet. When two neighboring necks or notches explode, the shock of the explosion compresses the intermediate jet or rod segment axially and the material is forced out radially. The disruption phenomena in the jet and rod experiments are similar with rapid expansion of the metal at explosion and at comparable velocities.
|
|
| 7. |
|
|
| 8. |
- Elfsberg, Mattias, et al.
(författare)
-
Experimental studies on a coaxial vircator, designed for operation in TE11 mode
- 2011
-
Ingår i: Proc. of Pulse Power Conference (PPC 2011). ; , s. 811-814
-
Konferensbidrag (refereegranskat)abstract
- Experiments on a coaxial vircator have been performed. A vircator is a narrow band high power microwave source without any external generated magnetic field [1]. A coaxial vircator is an advantageous design of a microwave radiation source for a compact HPM-system. With a limited size and outer diameter it is possible to use a larger emitting area compared to an axial design. A conventional coaxial vircator will generate the radiation in TM01 mode, due to its geometrical properties. For a compact HPM-system, radiation in TE11 mode is preferred when the radiated energy needs to be focused on a specific target. For operation in TE11 mode a sectioned emitter can be used rather than a circumcircular. The efficiency of the vircator can be greatly improved by optimizing the geometry of the vircator housing. The impedance of the pulsed power supply driving the vircator and the impedance of the vircator, depending on the A-K gap and amount of emitting material, is also important for maximizing the vircator efficiency. For the experiments reported on, the vircator was driven by a 500 kV/500 J compact Marx generator that can be operated repetitively at 10 Hz. For these experiments, the Marx generator was operating in single shot mode. During the experiments presented here, a couple of geometrical features were varied as well as the applied voltage. Their influence on the radiated field strength, dominating frequency and bandwidth are reported on and discussed.
|
|
| 9. |
- Hurtig, Lars Tomas Gustav, et al.
(författare)
-
Investigation Into Relativistic Magnetic Flux Amplification
- 2016
-
Ingår i: IEEE Transactions on Plasma Science. - : IEEE. - 0093-3813 .- 1939-9375. ; 44:1, s. 2-6
-
Tidskriftsartikel (refereegranskat)abstract
- Amplification of magnetic flux and electric polarization fields caused by a plasma streaming at relativistic velocity into a magnetic field is discussed. It is shown that the electrostatic polarization field that arises in a plasma beam streaming across magnetic field lines at relativistic velocities will cause amplification of the magnetic flux. This effect is in complete contrast to the expulsion of the magnetic field from the plasma interior that can be expected in high beta(K) plasmas, where beta(K) is the kinetic energy density in the plasma stream divided by the energy density in the magnetic field. The amplification is shown to be caused by the relativistic motion of the space charge layers setting up the polarization field. 3-D electromagnetic particle-in-cell simulations that support this theory are presented.
|
|
| 10. |
- Hurtig, Tomas, et al.
(författare)
-
Probes for High Frequency Measurements in a Plasma Gun
- 2003
-
Ingår i: Rev. Sci. Instr. (AIP). - : AIP Publishing. - 0034-6748. ; 74, s. 1153-1155
-
Tidskriftsartikel (refereegranskat)abstract
- High-frequency correlation measurements of plasma density, and electric and magnetic fields in a plasma gun have been performed. In this article, we give a description of the probes developed for this purpose. The probes described are characterized by a large bandwidth (>15 MHz) and very low susceptibility to electrostatic noise.
|
|
