| 11. |
|
|
| 12. |
|
|
| 13. |
- Gustavsson, Johan, 1974, et al.
(författare)
-
High-speed 850-nm VCSELs for 40 Gb/s transmission
- 2010
-
Konferensbidrag (övrigt vetenskapligt/konstnärligt)abstract
- We have explored the possibility to extend the data transmission rate for standard 850-nm GaAs-based VCSELs beyond the 10 Gbit/s limit of today's commercially available directly-modulated devices. By sophisticated tailoring of the design for high-speed performance we demonstrate that 10 Gb/s is far from the upper limit. For example, the thermal conductivity of the bottom mirror is improved by the use of binary compounds, and the electrical parasitics are kept at a minimum by incorporating a large diameter double layered oxide aperture in the design. We also show that the intrinsic high speed performance is significantly improved by replacing the traditional GaAs QWs with strained InGaAs QWs in the active region. The best overall performance is achieved for a device with a 9 μm diameter oxide aperture, having in a threshold current of 0.6 mA, a maximum output power of 9 mW, a thermal resistance of 1.9 °C/mW, and a differential resistance of 80 Ω. The measured 3dB bandwidth exceeds 20 GHz, and we experimentally demonstrate that the device is capable of error-free transmission (BER
|
|
| 14. |
- Gustavsson, Johan, 1974, et al.
(författare)
-
High speed 850nm VCSELs for >40Gb/s transmission
- 2013
-
Ingår i: 2013 Optical Fiber Communication Conference and Exposition and the National Fiber Optic Engineers Conference, OFC/NFOEC 2013. - 9781479904570 ; , s. OTh4H.4-
-
Konferensbidrag (refereegranskat)abstract
- VCSELs capable of direct modulation exceeding 40Gb/s are needed in next generation optical interconnect standards. Using a refined high-speed design we demonstrate GaAs-based VCSELs having record-high 28GHz modulation bandwidth, and that operate error-free at 47Gb/s.
|
|
| 15. |
- Gustavsson, Johan, 1974, et al.
(författare)
-
High-speed, high-temperature VCSELs for optical interconnects
- 2013
-
Ingår i: 2013 IEEE Photonics Society Summer Topical Meeting Series, PSSTMS 2013. - 9781467350600 ; , s. 7-8
-
Konferensbidrag (refereegranskat)abstract
- Directly modulated VCSELs operating at 40Gb/s are required for next generation optical interconnect standards. Using a refined high-speed design we demonstrate GaAs-based VCSELs that operate error-free at 47Gb/s at 25°C, and 40Gb/s at 85°C.
|
|
| 16. |
- Gustavsson, Johan, 1974, et al.
(författare)
-
Mode and polarization control in VCSELs using shallow surface structures
- 2007
-
Ingår i: IET Optoelectronics. ; 1:5, s. 197-205
-
Tidskriftsartikel (refereegranskat)abstract
- Monolithic techniques for mode and polarisation control in vertical-cavity surface emitting lasers (VCSELs) using shallow surface structures are summarized and put in the context with other techniques in terms of performance and manufacturability. The method of using circular-symmetric surface structures for mode control and their combination with a sub-wavelength surface grating for simultaneous mode and polarisation control is described in detail, and adherent experimental results for both 850-nm and 1.3-µm oxide-confined VCSELs are presented.
|
|
| 17. |
- Gustavsson, Johan, 1974, et al.
(författare)
-
Optimized active region design for high speed 850 nm VCSELs
- 2009
-
Ingår i: CLEO/Europe - EQEC 2009 - European Conference on Lasers and Electro-Optics and the European Quantum Electronics Conference; Munich; Germany; 14 June 2009 through 19 June 2009. - 9781424440801 ; , s. Art. no. 5192928-
-
Konferensbidrag (refereegranskat)abstract
- Short wavelength (850 nm) VCSELs operating at speeds of 25 Gb/s and above are needed for future highcapacity, short reach data communication links. The modulation bandwidth is intrinsically limited by thedifferential gain of the QWs used in the active region of the VCSEL. In this work we explore the use of strainedInGaAs/AlGaAs QWs and benchmark the performance against conventional GaAs/AlGaAs QWs.An 8-band k⋅p model [1] was used to calculate the energy band dispersions, using band offsets from modelsolid theory [2]. In all cases, the QW and barrier compositions and QW thickness were chosen for a gain peak at845 nm, enabling emission at 850 nm with a small detuning between the gain peak and the cavity resonance.With increasing In-concentration the QW thickness is reduced and the Al-concentration in the barrier isincreased to maintain the gain peak at 845 nm and the number of QWs is increased to maintain opticalconfinement and enable operation at a low carrier density for high differential gain. It was found that theincorporation of up to 10% In leads to a significant reduction in threshold carrier density and increase indifferential gain. This is due to an increased separation and reduced mixing between the highest heavy-hole andlight-hole valence bands (Fig.1). A further increase of In concentration leads to a less marked improvement.With an optimum active region design (5 x 4 nm In0.10Ga0.90As/Al0.37Ga0.63As QWs) a differential gain twice ashigh as that of a conventional design with 3 x 8 nm GaAs/Al0.30Ga0.70As QWs was predicted (Table 1).The improvement of differential gain was experimentally confirmed by extracting the resonance frequencyand its dependence on current from the modulation response of VCSELs with optimized InGaAs/AlGaAs QWand conventional GaAs/AlGaAs QW active regions. The differential gain was calculated from the correspondingD-factors (Fig.2) [3]. Excellent agreement was obtained between theory and experiments (Table 1).VCSELs with an optimized InGaAs/AlGaAs QW active region have a modulation bandwidth of 20 GHz at25° and 15 GHz at 85°C [4] and have enabled error-free transmission over 50 (100) m multimode fiber up to 32(25) Gb/s at a bias current density as low as 11 kA/cm2 under direct current modulation.
|
|
| 18. |
- Haglund, Erik, 1985, et al.
(författare)
-
25 Gbit/s transmission over 500 m multimode fibre using 850 nm VCSEL with integrated mode filter
- 2012
-
Ingår i: Electronics Letters. - : Institution of Engineering and Technology (IET). - 1350-911X .- 0013-5194. ; 48:9, s. 517-518
-
Tidskriftsartikel (refereegranskat)abstract
- An integrated mode filter in the form of a shallow surface relief was used to reduce the spectral width of a high-speed 850 nm vertical-cavity surface-emitting laser (VCSEL). The mode filter reduced the RMS spectral width from 0.9 to 0.3 nm for a VCSEL with an oxide aperture as large as 5 mu m. Because of reduced effects of chromatic and modal fibre dispersion, the mode filter significantly increases the maximum error-free (bit error rate
|
|
| 19. |
- Haglund, Erik, 1985, et al.
(författare)
-
850 nm datacom VCSELs for higher-speed and longer-reach transmission
- 2013
-
Ingår i: European VCSEL Day 2013.
-
Konferensbidrag (refereegranskat)abstract
- The 850 nm GaAs-based VCSEL is already the dominating technology for transmitters in optical interconnects up to 100 m in datacenters, thanks to low-cost fabrication, excellent high-speed properties at low currents and the existence of high-speed OM4 multimode fiber optimized for this particular wavelength. Future datacenters will require faster and more energy-efficient VCSELs to increase the overall bandwidth and reduce the power consumption of the datacenter network. In addition, longer-reach interconnects exceeding 1 km will also be required as datacenters grow into large multi-building complexes.By optimizing the doping profiles of the DBRs to reduce resistance, using a short (½-λ) cavity to improve longitudinal optical confinement and optimizing the photon lifetime for optimal damping, we obtained a record-high small-signal modulation bandwidth of 28 GHz for a ~4 µm oxide aperture VCSEL. A 7 µm oxide aperture VCSEL (~27 GHz bandwidth) enabled error-free transmission (bit-error-rate 300 m), the large spectral width of VCSELs leads to severe signal degradation by fiber dispersion. We have investigated two methods of fabricating low-spectral width quasi-single mode VCSELs to mitigate this problem. By using a small oxide aperture of ~3 µm, error-free transmission was achieved at 22 Gbit/s over 1.1 km of OM4 fiber. An alternative approach is to use an integrated mode filter in the form of a shallow surface relief to reduce the spectral width of the VCSEL. The mode filter allows for the use of a larger oxide aperture and thereby enables a lower resistance and operation at a lower current density. A 5 µm oxide aperture VCSEL with a mode filter enabled error-free transmission at 25 Gbit/s over 500 m of OM4 fiber.
|
|
| 20. |
- Haglund, Erik, 1985, et al.
(författare)
-
Demonstration of post-growth wavelength control of VCSELs using high-contrast gratings
- 2015
-
Ingår i: HP Laboratories Technical Report. ; 70
-
Tidskriftsartikel (refereegranskat)abstract
- We demonstrate post-growth wavelength setting of vertical-cavity surface-emitting lasers (VCSELs) using high-contrast gratings (HCGs). By fabricating HCGs with different duty-cycle and period, the HCG reflection phase can be varied, in effect giving different optical cavity lengths for HCGVCSELs with different grating parameters. This enables fabrication of monolithic multi-wavelength HCG-VCSEL arrays for wavelength-division multiplexing (WDM). The GaAs HCG is suspended in air by selective removal of an InGaP sacrificial layer. Electrically injected 980-nm HCGVCSELs with sub-mA threshold currents indicate high reflectivity from the GaAs HCGs. Lasing over a wavelength span of 15 nm was achieved, enabling a 4-channel WDM array with 5 nm channel spacing. Device design, fabrication and experimental proof-of-concept are presented.
|
|
