| 31. |
- Andersson, Mattias, et al.
(författare)
-
Mobility and fill factor correlation in geminate recombination limited solar cells
- 2011
-
Ingår i: Journal of Applied Physics. - : American Institute of Physics (AIP). - 0021-8979 .- 1089-7550. ; 110:2, s. 024509-
-
Tidskriftsartikel (refereegranskat)abstract
- Empirical data for the fill factor as a function of charge carrier mobility for two different polymer: fullerene systems is presented and analyzed. The results indicate that charge extraction depth limitations and space charge effects are inconsistent with the observed behavior, and the decrease in the fill factor is, instead, attributed to the field-dependent charge separation and geminate recombination. A solar cell photocurrent limited by the Onsager-Braun charge transfer exciton dissociation is shown to be able to accommodate the experimental observations. Charge dissociation limited solar cells always benefit from increased mobilities, and the negative contribution from the reduced charge separation is shown to be much more important for the fill factor in these material systems than any adverse effects from charge carrier extraction depth limitations or space charge effects due to unbalanced mobilities. The logarithmic dependence of the fill factor on the mobility for such a process is also shown to imply that simply increasing the mobilities is an impractical way to reach very high fill factors under these conditions since unrealistically high mobilities are required. A more controlled morphology is, instead, argued to be necessary for high performance.
|
|
| 32. |
|
|
| 33. |
- Bai, Sai, et al.
(författare)
-
Electrophoretic deposited oxide thin films as charge transporting interlayers for solution-processed optoelectronic devices: the case of ZnO nanocrystals
- 2015
-
Ingår i: RSC Advances. - : Royal Society of Chemistry. - 2046-2069. ; 5:11, s. 8216-8222
-
Tidskriftsartikel (refereegranskat)abstract
- A promising fabrication method of electron transporting interlayers for solution-processed optoelectronic devices by electrophoretic deposition (EPD) of colloidal zinc oxide (ZnO) nanocrystals was demonstrated. A low voltage of 3-5 V and a short deposition time of 40 s at room temperature were found to be sufficient to generate dense and uniform ZnO thin films. The EPD ZnO nanocrystal films were applied as ETLs for inverted organic solar cell and polymer light emitting diodes (PLEDs). By optimizing the EPD processing of ZnO nanocrystal electron transporting layers (ETLs), inverted organic solar cells based on [3,4-b]-thiophene/benzodithiophene (PTB7): [6-6]-phenyl-C71-butyric acid methyl ester (PC71BM) and poly(3-hexylthiophene) (P3HT): [6-6]-phenyl-C-61-butyric acid methyl ester (PC61BM) with an average PCE of 8.4% and 4.0% were fabricated. In combination with the PLEDs and flexible devices results, we conclude that the EPD processed ZnOnanocrystal thin films can serve as high quality ETLs for solution-processed optoelectronic devices.
|
|
| 34. |
- Bai, Sai, et al.
(författare)
-
Ethanedithiol Treatment of Solution-Processed ZnO Thin Films: Controlling the Intragap States of Electron Transporting Interlayers for Efficient and Stable Inverted Organic Photovoltaics
- 2015
-
Ingår i: Advanced Energy Materials. - : Wiley-VCH Verlag. - 1614-6832 .- 1614-6840. ; 5:5, s. 1401606-
-
Tidskriftsartikel (refereegranskat)abstract
- The surface defects of solution-processed ZnO films lead to various intragap states. When the solution-processed ZnO films are used as electron transport interlayers (ETLs) in inverted organic solar cells, the intragap states act as interfacial recombination centers for photogenerated charges and thereby degrade the device performance. Here, a simple passivation method based on ethanedithiol (EDT) treatment is demonstrated, which effectively removes the surface defects of the ZnO nanocrystal films by forming zinc ethanedithiolates. The passivation by EDT treatment modulates the intragap states of the ZnO films and introduces a new intragap band. When the EDT-treated ZnO nanocrystal films are used as ETLs in inverted organic solar cells, both the power conversion efficiency and stability of the devices are improved. The control studies show that the solar cells with EDT-treated ZnO films exhibit reduced charge recombination rates and enhanced charge extraction properties. These features are consistent with the fact that the modulation of the intragap states results in reduction of interfacial recombination as well as the improved charge selectivity and electron transport properties of the ETLs. It is further demonstrated that the EDT treatment-based passivation method can be extended to ZnO films deposited from sol-gel precursors.
|
|
| 35. |
|
|
| 36. |
|
|
| 37. |
- Barrau, Sophie, et al.
(författare)
-
Nanomorphology of Bulk Heterojunction Organic Solar Cells in 2D and 3D Correlated to Photovoltaic Performance
- 2009
-
Ingår i: Macromolecules. - : American Chemical Society (ACS). - 0024-9297 .- 1520-5835. ; 42:13, s. 4646-4650
-
Tidskriftsartikel (refereegranskat)abstract
- Control of the nanoscale morphology of the donor-acceptor material blends inorganic solar Cells is critical for optimizing the photovoltaic performances. The influence of intrinsic (acceptor materials) and extrinsic (donor:acceptor weight ratio, substrate, solvent) parameters was investigated, by atomic force microscopy (AFM) and electron tomography (ET), on the nanoscale phase separation of blends of a low-band-gap alternating polyfluorene copolymers (APFO-Green9) with [6,6]-phenyl-C-71-butyric acid methyl ester ([70]PCBM). The photovoltaic performances display an optimal efficiency for the device elaborated with a 1:3 APFO-Green polymer:[70][PCBM weight ratio and spin-coated from chloroform solution. The associated active layer morphology presents small phase-separated domains which is a good balance between as a large interfacial donor-acceptor area and Continuous paths of the donor and acceptor phases to the electrodes.
|
|
| 38. |
- Bjoerstroem, Cecilia M., et al.
(författare)
-
Influence of solvents and substrates on the morphology and the performance of low-bandgap polyfluorene: PCBM photovoltaic devices
- 2006
-
Ingår i: Proceedings of SPIE-The International Society for Optical Engineering. ; 6192, s. 61921X/1-
-
Konferensbidrag (refereegranskat)abstract
- Spin-coated thin films of poly[(9,9-dioctylfluorenyl-2,7-diyl)-co-5,5-(4',7'-di-2-thienyl-2',1',3'-benzothiadiazole)] (APFO-3) blended with [6,6]-phenyl-C61-butyric acid Me ester (PCBM) are used as the active material in polymer photovoltaic cells. Such blends are known for their tendency to phase sep. during film formation. Tuning the morphol. of the blend in a controlled way is one possible road towards higher efficiency. We studied the effect of adding chlorobenzene to chloroform-based blend solns. before spin-coating on the conversion efficiency of APFO-3:PCBM photodiodes, and related that to the lateral and vertical morphol. of thin films of the blend. The lateral morphol. is imaged by at. force microscopy (AFM) and the vertical compositional profile is obtained by dynamic secondary ion mass spectrometry (SIMS). The profiles reveal compositional variations consisting of multilayers of alternating polymer-rich and PCBM-rich domains in the blend film spin-coated from chloroform. The vertical compositional variations are caused by surface-directed spinodal waves and are frozen in during the rapid evapn. of a highly volatile solvent. With addn. of the low-vapor pressure solvent chlorobenzene, a more homogeneous vertical compn. is found. The conversion efficiency for solar cells of this blend was found to be optimal for chloroform:chlorobenzene mixts. with a vol.-ratio of 80:1. We have also investigated the role of the substrate on the morphol. We found that blend films spin-coated from chloroform solns. on PEDOT:PSS-coated ITO show a similar compositional structure as the films on silicon, and that changing the substrate from silicon to gold only affects the vertical phase sepn. in a region close to the substrate interface. [on SciFinder (R)]
|
|
| 39. |
- Bjorstrom, Cecilia M., et al.
(författare)
-
Influence of solvents and substrates on the morphology and the performance of low-bandgap polyfluorene: PCBM photovoltaic devices - art. no. 61921X
- 2006
-
Ingår i: Proceedings of SPIE, the International Society for Optical Engineering. - : International Society for Optical Engineering; 1999. - 0277-786X .- 1996-756X. ; 6192, s. X1921-X1921
-
Tidskriftsartikel (refereegranskat)abstract
- Spin-coated thin films of poly[(9,9-dioctylfluorenyl-2,7-diyl)-co-5,5-(4,7-di-2-thienyl-2,1,3-benzothiadiazole)] (APFO-3) blended with [6,6]-phenyl-C-61-butyric acid methyl ester (PCBM) are used as the active material in polymer photovoltaic cells. Such blends are known for their tendency to phase separate during film formation. Tuning the morphology of the blend in a controlled way is one possible road towards higher efficiency. We studied the effect of adding chlorobenzene to chloroform-based blend solutions before spin-coating on the conversion efficiency of APFO-3:PCBM photodiodes, and related that to the lateral and vertical morphology of thin films of the blend. The lateral morphology is imaged by atomic force microscopy (AFM) and the vertical compositional profile is obtained by dynamic secondary ion mass spectrometry (SIMS). The profiles reveal compositional variations consisting of multilayers of alternating polymer-rich and PCBM-rich domains in the blend film spin-coated from chloroform. The vertical compositional variations are caused by surface-directed spinodal waves and are frozen in during the rapid evaporation of a highly volatile solvent. With addition of the low-vapour pressure solvent chlorobenzene, a more homogeneous vertical composition is found. The conversion efficiency for solar cells of this blend was found to be optimal for chloroform: chlorobenzene mixtures with a volume-ratio of 80:1. We have also investigated the role of the substrate on the morphology. We found that blend films spin-coated from chloroform solutions on PEDOT:PSS-coated ITO show a similar compositional structure as the films on silicon, and that changing the substrate from silicon to gold only affects the vertical phase separation in a region close to the substrate interface.
|
|
| 40. |
|
|
