| 1. |
- Janhäll, Sara, et al.
(author)
-
Vertical distribution of air pollutants at the Gustavii Cathedral in Göteborg, Sweden
- 2003
-
In: Atmospheric Environment. - : Elsevier. - 1352-2310 .- 1873-2844. ; 37:2, s. 209-217
-
Journal article (peer-reviewed)abstract
- Atmospheric trace gases and particles were measured at two heights at the Gustavii Cathedral in Göteborg, Sweden, during 7 weeks in September and October 1999. The Gustavii Cathedral is situated in the city centre of Göteborg, which is near the harbour area and encircled by heavy traffic some hundred metres away. The main body of the church is as high as the surrounding buildings, while the tower extends well above. The sampling points were placed on the west wall of the tower at 10 and 32 meter height, i.e. well below and above the roof top level of surrounding buildings, respectively.Sulphur dioxide and nitric acid were sampled using the denuder technique and analysed by Ion Chromatography, IC. Total suspended particulates (TSP) were sampled using filter cups and subsequently analysed by energy dispersive X-ray fluorescence spectroscopy (EDXRF). In addition to the diurnal sampling of species, nitrogen oxides were measured using chemiluminescence detectors. Additional data from the Environmental Office in Göteborg was used in the analysis.Differences between the concentrations measured at the upper and lower levels were calculated and their variation and dependence on meteorological factors were evaluated. On the average larger concentrations were found at the lower level for soil derived elements and TSP, while nitric acid and nitric oxide showed larger concentrations at the upper level. Sulphur dioxide and nitrogen dioxide, as well as many of the elements in the TSP, showed equal concentrations at the two levels. However, depending on wind direction the measured differences of nitrogen oxides could be both positive and negative.
|
|
| 2. |
- Molnár, Peter, 1967, et al.
(author)
-
Roadside measurements of fine and ultrafine particles at a major road north of Gothenburg
- 2002
-
In: Atmospheric Environment. - 1352-2310 .- 1873-2844. ; 36:25, s. 4115-4123
-
Journal article (peer-reviewed)abstract
- Particle measurements were conducted at a road site 15 km north of the city of Gothenburg for 3 weeks in June 2000. The size distribution between 10 and 368 nm was measured continuously by using a differential mobility particle sizer (DMPS) system. PM2.5 was sampled on a daily basis with subsequent elemental analysis using EDXRF-spectroscopy. The road is a straight four-lane road with a speed limit of 90 kph. The road passing the site is flat with no elevations where the vehicles run on a steady workload and with constant speed. The traffic intensity is about 20,000 cars per workday and 13,000 vehicles per day during weekends. The diesel fuel used in Sweden is low in sulphur content (< 10 ppm) and therefore the diesel vehicles passing the site contribute less to particle emissions in comparison with other studies. A correlation between PM2.5 and accumulation mode particles (100-368 nm) was observed. However, no significant correlation was found between number concentrations of ultrafine particles (10-100 nm) and PM2.5 or the accumulation mode number concentration. The particle distribution between 10 and 368 nm showed great dependency on wind speed and wind direction, where the wind speed was the dominant factor for ultrafine (10-100nm) particle concentrations. The difference in traffic intensity between workday and weekend together with wind data made it possible to single out the traffic contribution to particle emissions and measure the size distribution. The results presented in combination with previous studies show that both PM2.5 and the mass of accumulation mode particles are bad estimates for ultrafine particles. (C) 2002 Elsevier Science Ltd. All rights reserved.
|
|
| 3. |
- Alves, C. A., et al.
(author)
-
Physical and chemical properties of non-exhaust particles generated from wear between pavements and tyres
- 2020
-
In: Atmospheric Environment. - : Elsevier Ltd. - 1352-2310 .- 1873-2844. ; 224
-
Journal article (peer-reviewed)abstract
- A road simulator was used to generate wear particles from the interaction between two tyre brands and a composite pavement. Particle size distributions were monitored using a scanning mobility particle sizer and an aerosol particle sizer. Continuous measurements of particle mass concentrations were also made. Collection of inhalable particles (PM10) was conducted using a high-volume sampler equipped with quartz filters, which were then analysed for organic and elemental carbon, organic constituents and elemental composition. Tyre fragments chopped into tiny chips were also subjected to detailed organic and elemental speciation. The number concentration was dominated by particles <0.5 μm, whereas most of the mass was found in particles >0.5 μm. The emission factor from wear between pavements and tyres was of the order of 2 mg km−1 veh−1. Organic carbon represented about 10% of the PM10 mass, encompassing multiple aliphatic compounds (n-alkanes, alkenes, hopanes, and steranes), PAHs, thiazols, n-alkanols, polyols, some fragrant compounds, sugars, triterpenoids, sterols, phenolic constituents, phthalate plasticisers and several types of acids, among others. The relationship between airborne particulate organic constituents and organic matter in tyre debris is discussed. The detection of compounds that have been extensively used as biomass burning tracers (e.g. retene, dehydroabietic acid and levoglucosan) in both the shredded tiny tyre chips and the wear particles from the interaction between tyres and pavement puts into question their uniqueness as markers of wood combustion. Trace and major elements accounted for about 5% of the mass of the tyre fragments but represented 15–18% of the PM10 from wear, denoting the contribution of mineral elements from the pavement. Sulphur and zinc were abundant constituents in all samples.
|
|
| 4. |
- Dahl, Andreas, et al.
(author)
-
Traffic-generated emissions of ultrafine particles from pavement-tire interface
- 2006
-
In: Atmospheric Environment. - : Elsevier. - 1352-2310 .- 1873-2844. ; 40:7, s. 1314-1323
-
Journal article (peer-reviewed)abstract
- In a road simulator study, a significant source of sub-micrometer fine particles produced by the road-tire interface was observed. Since the particle size distribution and source strength is dependent on the type of tire used, it is likely that these particles largely originate from the tires, and not the road pavement. The particles consisted most likely of mineral oils from the softening filler and fragments of the carbon-reinforcing filler material (soot agglomerates). This identification was based on transmission electron microscopy studies of collected ultrafine wear particles and on-line thermal treatment using a thermodesorber. The mean particle number diameters were between 15-50 nm, similar to those found in light duty vehicle (LDV) tail-pipe exhaust. A simple box model approach was used to estimate emission factors in the size interval 15-700 nm. The emission factors increased with increasing vehicle speed, and varied between 3.7 x 10(11) and 3.2 x 10(12) particles vehicle(-1) km(-1) at speeds of 50 and 70 km h(-1). This corresponds to between 0.1-1% of tail-pipe emissions in real-world emission studies at similar speeds from a fleet of LDV with 95% gasoline and 5% diesel-fueled cars. The emission factors for particles originating from the road-tire interface were, however, similar in magnitude to particle number emission factors from liquefied petroleum gas-powered vehicles derived in test bench studies in Australia 2005. Thus the road-tire interface may be a significant contributor to particle emissions from ultraclean vehicles. (c) 2005 Elsevier Ltd. All rights reserved.
|
|
| 5. |
- Denby, Bruce Rolstad, et al.
(author)
-
A coupled road dust and surface moisture model to predict non-exhaust road traffic induced particle emissions (NORTRIP). Part 1 : Road dust loading and suspension modelling
- 2013
-
In: Atmospheric Environment. - : Elsevier BV. - 1352-2310 .- 1873-2844. ; 77, s. 283-300
-
Journal article (peer-reviewed)abstract
- Non-exhaust traffic induced emissions are a major source of particle mass in most European countries. This is particularly important in Nordic and Alpine countries where winter time road traction maintenance occurs, e.g. salting and sanding, and where studded tyres are used. In this paper, Part 1, the road dust sub-model of a coupled road dust and surface moisture model (NORTRIP) is described. The model provides a generalised process based formulation of the non-exhaust emissions, with emphasis on the contribution of road wear, suspension, surface dust loading and the effect of road surface moisture (retention of wear particles and suspended emissions). The model is intended for use as a tool for air quality managers to help study the impact of mitigation measures and policies. We present a description of the road dust sub-model and apply the model to two sites in Stockholm and Copenhagen where seven years of data with surface moisture measurements are available. For the site in Stockholm, where studded tyres are in use, the model predicts the PM10 concentrations very well with correlations (R-2) in the range of R-2 = 0.76-0.91 for daily mean PM10. The model also reproduces well the impact of a reduction in studded tyres at this site. For the site in Copenhagen the correlation is lower, in the range 0.44-0.51. The addition of salt is described in the model and at both sites this leads to improved correlations due to additional salt emissions. For future use of the model a number of model parameters, e.g. wear factors and suspension rates, still need to be refined. The effect of sanding on PM10 emissions is also presented but more information will be required before this can be confidently applied for management applications. (C) 2013 Elsevier Ltd. All rights reserved.
|
|
| 6. |
- Denby, Bruce Rolstad, et al.
(author)
-
A coupled road dust and surface moisture model to predict non-exhaust road traffic induced particle emissions (NORTRIP). Part 2 : Surface moisture and salt impact modelling
- 2013
-
In: Atmospheric Environment. - : Elsevier. - 1352-2310 .- 1873-2844. ; 81, s. 485-503
-
Journal article (peer-reviewed)abstract
- Non-exhaust traffic induced emissions are a major source of airborne particulate matter in most European countries. This is particularly important in Nordic and Alpine countries where winter time road traction maintenance occurs, e.g. salting and sanding, and where studded tyres are used. Though the total mass generated by wear sources is a key factor in non-exhaust emissions, these emissions are also strongly controlled by surface moisture conditions. In this paper, Part 2, the road surface moisture submodel of a coupled road dust and surface moisture model (NORTRIP) is described.We present a description of the road surface moisture part of the model and apply the coupled model to seven sites in Stockholm, Oslo, Helsinki and Copenhagen over 18 separate periods, ranging from 3.5 to 24 months. At two sites surface moisture measurements are available and the moisture sub-model is compared directly to these observations. The model predicts the frequency of wet roads well at both sites, with an average fractional bias of -2.6%. The model is found to correctly predict the hourly surface state, wet or dry, 85% of the time. From the 18 periods modelled using the coupled model an average absolute fractional bias of 15% for PM10 concentrations was found. Similarly the model predicts the 90'th daily mean percentiles of PMio with an average absolute bias of 19% and an average correlation (R-2) of 0.49. When surface moisture is not included in the modelling then this average correlation is reduced to 0.16, demonstrating the importance of the surface moisture conditions. Tests have been carried out to assess the sensitivity of the model to model parameters and input data. The model provides a useful tool for air quality management and for improving our understanding of non-exhaust traffic emissions.
|
|
| 7. |
- Denby, B. R., et al.
(author)
-
Road salt emissions : A comparison of measurements and modelling using the NORTRIP road dust emission model
- 2016
-
In: Atmospheric Environment. - : Elsevier Ltd. - 1352-2310 .- 1873-2844. ; 141, s. 508-522
-
Journal article (peer-reviewed)abstract
- De-icing of road surfaces is necessary in many countries during winter to improve vehicle traction. Large amounts of salt, most often sodium chloride, are applied every year. Most of this salt is removed through drainage or traffic spray processes but a certain amount may be suspended, after drying of the road surface, into the air and will contribute to the concentration of particulate matter. Though some measurements of salt concentrations are available near roads, the link between road maintenance salting activities and observed concentrations of salt in ambient air is yet to be quantified. In this study the NORTRIP road dust emission model, which estimates the emissions of both dust and salt from the road surface, is applied at five sites in four Nordic countries for ten separate winter periods where daily mean ambient air measurements of salt concentrations are available. The model is capable of reproducing many of the salt emission episodes, both in time and intensity, but also fails on other occasions. The observed mean concentration of salt in PM10, over all ten datasets, is 4.2 μg/m3 and the modelled mean is 2.8 μg/m3, giving a fractional bias of −0.38. The RMSE of the mean concentrations, over all 10 datasets, is 2.9 μg/m3 with an average R2 of 0.28. The mean concentration of salt is similar to the mean exhaust contribution during the winter periods of 2.6 μg/m3. The contribution of salt to the kerbside winter mean PM10 concentration is estimated to increase by 4.1 ± 3.4 μg/m3 for every kg/m2 of salt applied on the road surface during the winter season. Additional sensitivity studies showed that the accurate logging of salt applications is a prerequisite for predicting salt emissions, as well as good quality data on precipitation. It also highlights the need for more simultaneous measurements of salt loading together with ambient air concentrations to help improve model parameterisations of salt and moisture removal processes. © 2016 The Authors
|
|
| 8. |
- Grigoratos, Theodoros, et al.
(author)
-
Experimental investigation of tread wear and particle emission from tyres with different treadwear marking
- 2018
-
In: Atmospheric Environment. - : PERGAMON-ELSEVIER SCIENCE LTD. - 1352-2310 .- 1873-2844. ; 182, s. 200-212
-
Journal article (peer-reviewed)abstract
- The Treadwear Rating (TWR) provided on the sidewall of the tyre is a marking intended to inform the customer about the expected durability of the tyre. The current study explores whether there is a correlation between the TWR and tyres' tread mass loss. Furthermore, it explores the possible correlation between the TWR and tyre wear dust emitted in the form of PM10 and PM2.5. For that reason, two tyres of the same brand (B) but with different TWR and three tyres of different brands (C and D with the same TWR as one of the B tyres and A with a lower TWR) were tested at a constant speed of 70 km/h by means of the Swedish National Road and Transport Research Institute (VTI) road simulator. Tyres of the same TWR but of different brands showed different behaviour in terms of material loss, PM, and PN emissions under the selected testing conditions. This means that it is not feasible to categorize tyres of different brands in terms of their emissions based on their TWR. The test performed on the two tyres of the same brand but with different TWR showed instead a substantial (not statistically significant) difference in both total wear and PM10 emissions. The tyre with the higher TWR (B2) showed less wear and PM10 emissions compared to the B1 tyre having a lower TWR. Since only two tyres of the same brand and with different TWR were tested, this result cannot be generalized and more tests are necessary to confirm the relation within the same brand. In general, the tyre tread mass loss showed no obvious statistical relation to PM10, PM2.5 or PN concentration. In all cases approximately 50% (by mass) of emitted PM10 fall within the size range of fine particles, while PN size distribution is dominated by nanoparticles most often peaking at 20-30 nm.
|
|
| 9. |
- Janhäll, Sara, 1965-
(author)
-
Review on urban vegetation and particle air pollution - Deposition and dispersion
- 2015
-
In: Atmospheric Environment. - : Elsevier Ltd. - 1352-2310 .- 1873-2844. ; 105, s. 130-137
-
Research review (peer-reviewed)abstract
- Urban vegetation affects air quality through influencing pollutant deposition and dispersion. Both processes are described by many existing models and experiments, on-site and in wind tunnels, focussing e.g. on urban street canyons and crossings or vegetation barriers adjacent to traffic sources. There is an urgent need for well-structured experimental data, including detailed empirical descriptions of parameters that are not the explicit focus of the study.This review revealed that design and choice of urban vegetation is crucial when using vegetation as an ecosystem service for air quality improvements. The reduced mixing in trafficked street canyons on adding large trees increases local air pollution levels, while low vegetation close to sources can improve air quality by increasing deposition. Filtration vegetation barriers have to be dense enough to offer large deposition surface area and porous enough to allow penetration, instead of deflection of the air stream above the barrier. The choice between tall or short and dense or sparse vegetation determines the effect on air pollution from different sources and different particle sizes. © 2015 The Author.
|
|
| 10. |
- Janhäll, Sara, 1965, et al.
(author)
-
Size resolved traffic emission factors of submicrometer particles
- 2004
-
In: Atmospheric Environment. - : Elsevier BV. - 1352-2310 .- 1873-2844. ; 38:26, s. 4331-4340
-
Journal article (peer-reviewed)abstract
- Size resolved emission factors for submicrometer particles related to trace gases have been obtained from measurement data at a suburban road side, with a traffic intensity of 18,000 vehicles per day. Number of particles with diameter 10-368 nm, trace gases (NO, NOx, O-3 and SO2) traffic and meteorology parameters were measured outside of Goteborg, Sweden. Size distributions of small particles at the site are presented and their relation to meteorological and traffic related variables was evaluated. Wind speed correlated negatively with 10-368 nm particles and temperature correlated negatively with the smaller particles (10-60 nm). Nitric oxide was shown to be a better tracer for traffic related ultrafine particles, than traffic intensity itself. The calculated emission factor, with errors at 95% confidence level, for particles in the range 10-368 nm is presented in relation to nitrogen oxides. The emission factors were 268+/-60 and 176+/-37 particles cm(-3) per ppb NO and NOx, respectively. The particle emission factors for 10-100, 10-50, 50-170 and 170-368 nm were 260+/-70, 228+/-52, 41+/-11 and <1 particle cm(-3) per ppb NO, respectively. The size distribution of the emissions is given by number of particles normalised by the width of the size bin, i.e. in units of dNd log Dp(-1) ppb(-1). The maximum normalised emission factor was 450 cm(-3) per ppb NO for 20 nm particles. The shape of the size distribution of emissions revealed one sharp peak at 20 nm, with a small shoulder at 70 nm. (C) 2004 Elsevier Ltd. All rights reserved.
|
|
