| 11. |
- Odenberger, Mikael, 1977, et al.
(författare)
-
Prospects for CCS in the EU energy roadmap to 2050
- 2013
-
Ingår i: Energy Procedia. - : Elsevier BV. - 1876-6102. ; 37, s. 7573-7581
-
Konferensbidrag (refereegranskat)abstract
- The aim of this paper is to estimate the prospects of carbon capture and storage (CCS) in the European electricity supply system taking into account possible forthcoming policy based on the recent EU Energy Roadmap communication, which suggests a 93 to 99% reduction in CO2 emissions relative 1990 levels from the electricity sector by the year 2050. Furthermore, the effect of whether or not onshore storage will be accepted is investigated. The work is based on techno-economic modeling of the European electricity generation sector under different assumptions (scenarios) of the future with respect to electricity demand and fuel prices. The results indicate that the contribution from CCS on a member state level depends on local conditions, e.g., access to local fuels like lignite, and whether or not onshore storage will be allowed. Excluding on-shore storage in aquifers, the modeling results give that CCS is centralized around the North Sea. Natural gas fired conventional power plants is likely to be a serious competitor to coal CCS in the short to medium term providing large emission reduction opportunities by fuel shifting from existing coal power plants to new high efficient gas fired combined cycles. Such development can be a barrier for early deployment of CCS, and hence, result in a delay in commercialization of CCS. The scenarios presented in the Energy Roadmap prescribe power systems almost without net CO2 emissions by 2050, which implies that CCS technologies by the year 2050 must be of a zero-emission type. The modeling presented here indicates in general a large increase in technologies with low CO2 emissions, renewables as well as a significant contribution from CCS technologies, where CCS in the investigated scenarios have the potential to contribute as much as 25-35% of total electricity generation at around year 2050.
|
|
| 12. |
- Pizarro, Amalia, et al.
(författare)
-
What is the future potential for imports of combustible municipal waste to countries with extensive district heating networks? A case study of Denmark
- 2015
-
Ingår i: Proceedings of Sardinia 2015 Fifteenth International Waste Management and Landfill Symposium. ; 9788862650212
-
Konferensbidrag (refereegranskat)abstract
- In Europe, landfilling is the most widely used method for managing municipal solid waste. By contrast, the northern European waste market is characterized by high capacities from energy recovery plants, mostly incineration in cogeneration facilities. In Denmark, there is an overcapacity of incineration plants and this study aims to analyse if import of waste is beneficial during an interim period to divert landfilling or if it might be profitable to invest in overcapacity in the long-term in those countries where heat from incineration can be recovered. The energy and waste management system are described through linking of mathematical models, taking a holistic approach. In the short-term it pays off to import waste, avoiding landfilling; however, in the longer-term, benefits from waste trading will depend on the price of heat markets.
|
|
| 13. |
- Santén, Vendela, 1978
(författare)
-
Exploring logistics actions enabling environmentally sustainable freight transport
- 2013
-
Licentiatavhandling (övrigt vetenskapligt/konstnärligt)abstract
- To curb unsustainable freight transport trends; such as transport growth, larger dependency on road transport and generally an increased share of greenhouse gas emissions from the sector, actions needs to be taken among actors in the logistics system. The purpose of this thesis is to explore logistics actions that enable environmentally sustainable freight transport. This explorative research, based primarily on empirical data from interviews, focus groups, and a case study, adopts the perspectives of different actors in the logistics system: transport buyers, freight forwarders, transport operators, and authorities. The thesis identifies a wide range of actions in the logistics system to potentially enable environmentally sustainable freight transport. The perception from actors regarding what actions are important to adopt indicate that more knowledge among actors regarding how transport and traffic work can be reduced and how different actions affect each other are needed; especially how transport buyers acting affect the transport operations performed by freight forwarders and transport operators. By exploring what hinders environmentally sustainable freight transport in the interface between transport buyers and providers, it can be concluded that closer co-operation can provide better internal conditions for actors and new business solutions. Open dialogue, information sharing, and proactivity among both transport buyers and transport providers are essential. Furthermore, in order to increase load factor in practice, actions can be taken by transport buyers in the area of packaging, loading, and booking efficiency. More flexible time requirements will potentially increase the load factor. Gaining positive environmental effects from these changes is dependent on the freight forwarder’s actions in terms of consolidating with other transport buyers’ goods, route planning, and the positioning of vehicles. Since improvements in one actor’s system may not necessarily yield positive effects at a higher system level, it is important to also have a holistic view when aiming for environmentally sustainable freight transport. This thesis contributes with knowledge about how logistics actors can work toward environmentally sustainable freight transportation by providing insight for managers of transport buying and transport providing companies by exemplifying the interactions between actors and actions and their potential effects.
|
|
| 14. |
- Sotnikov, Artem, 1985, et al.
(författare)
-
Simulations of a solar-assisted block-heating system
- 2017
-
Ingår i: ISES Solar World Congress 2017 - IEA SHC International Conference on Solar Heating and Cooling for Buildings and Industry 2017, Proceedings. - Freiburg, Germany : International Solar Energy Society.
-
Konferensbidrag (refereegranskat)abstract
- Two types of simulation software TRNSYS and Polysun are studied to check their suitability for solar district heating system planning. A reference case, a part of the Vallda Heberg district heating system is modelled in both tools and results are compared with available measured data and with each other. Models are successfully calibrated. TRNSYS and Polysun models have deviations in main key figures compared to the reference case less than 2% and less than 8% respectively. A sensitivity analysis of key parameters shows that the two tools give similar results.
|
|
| 15. |
- Adl-Zarrabi, Bijan, 1959, et al.
(författare)
-
Sustainability Assessment of Infrastructure Elements with Integrated Energy Harvesting Technologies
- 2016
-
Ingår i: Energy and Environment. - : Wiley. - 9781119307761 ; , s. 221-234
-
Bokkapitel (övrigt vetenskapligt/konstnärligt)abstract
- The possibility of integrating energy harvesting devices into the bridge/tunnel structures along Coastal Highway Route E39 has been investigated in a feasibility study by the Norwegian Public Roads Administration (NPRA). The main advantage of integrating energy conversion devices in a structural element is the reduction of costs compared to stand-alone devices. The construction could be used as a foundation, a mooring point and provide a dry environment for electrical devices. Easy access to the production site could also reduce the cost for installation, operation and maintenance. Two important challenges related to harvesting renewable energy by infrastructure elements, without concerning about the energy source, are to store it or feed the energy to the grid. In the second case, tailoring generation to demand is of critical importance. Tasks such as supply and demand management, for instance, peak hour management, what kind of storage should be used - electrical or thermal - need be solved. Furthermore, integrating energy production devices in a structure might cause negative environmental impacts and affect the life expectancy and maintenance costs of such structures. The potential environmental impacts associated with renewable technologies are the consequences for bird life or marine fauna at the fjord crossing locations, as well as noise and visual impact. Thus, a sustainability assessment should be performed in order to quantify the ecological, economical and societal impacts of the suggested alternatives.
|
|
| 16. |
- Agrawal, Munmun, et al.
(författare)
-
Global market trends of tantalum and recycling methods from Waste Tantalum Capacitors: A review
- 2021
-
Ingår i: Sustainable Materials and Technologies. - : Elsevier BV. - 2214-9937. ; 29
-
Forskningsöversikt (refereegranskat)abstract
- The rapid digitalization of the world, technological up-gradation, and shorten life cycle of electronic gadgets leading to the generation of an enormous amount of waste tantalum capacitors (WTCs) rich in tantalum every year. The need of the hour is to develop an effective way to recycle tantalum from these waste scraps considering the scarcity of tantalum, environmental impacts, resource and energy utilization, and lower recycling rates. In this paper, various existing methods of recovery of metallic tantalum from WTCs have been extensively reviewed. Processes have been examined in light of recovery efficiency, purity of the resultant product, process complexity, and limitations. The bottleneck in the recovery of tantalum from WTCs is the presence of tightly covered mold resin over the surface of the tantalum anode. Various researchers have recovered Ta with varying degrees of success. Pyrolysis, followed by chloride metallurgy, has been proven to be an effective technology on account of its high removal rate, resource and energy utilization, and lesser environmental impacts. This article also explores the global scenario of tantalum. Overall this review provides a foundation to understand the potential barrier and various opportunities associated with the recovery of tantalum from WTCs.
|
|
| 17. |
- Ahlgren, Serina, et al.
(författare)
-
Review of methodological choices in LCA of biorefinery systems - key issues and recommendations
- 2015
-
Ingår i: Biofuels, Bioproducts and Biorefining. - : Wiley. - 1932-1031 .- 1932-104X. ; 9:5, s. 606-619
-
Forskningsöversikt (refereegranskat)abstract
- The current trend in biomass conversion technologies is toward more efficient utilization of biomass feedstock in multiproduct biorefineries. Many life-cycle assessment (LCA) studies of biorefinery systems have been performed but differ in how they use the LCA methodology. Based on a review of existing LCA standards and guidelines, this paper provides recommendations on how to handle key methodological issues when performing LCA studies of biorefinery systems. Six key issues were identified: (i) goal definition, (ii) functional unit, (iii) allocation of biorefinery outputs, (iv) allocation of biomass feedstock, (v) land use, and (vi) biogenic carbon and timing of emissions. Many of the standards and guidelines reviewed here provide only general methodological recommendations. Some make more specific methodological recommendations, but these often differ between standards. In this paper we present some clarifications (e.g. examples of research questions and suitable functional units) and methodological recommendations (e.g. on allocation).
|
|
| 18. |
- Andreasi Bassi, Susanna, et al.
(författare)
-
A life cycle assessment framework for large-scale changes in material circularity
- 2021
-
Ingår i: Waste Management. - : Elsevier BV. - 0956-053X .- 1879-2456. ; 135, s. 360-371
-
Tidskriftsartikel (refereegranskat)abstract
- Increasing material circularity is high on the agenda of the European Union in order to decouple environmental impacts and economic growth. While life cycle assessment (LCA) is useful for quantifying the associated environmental impacts, consistent LCA modeling of the large-scale changes arising from policy targets addressing material circularity (i.e., recycled content and recycling rate) is challenging. In response to this, we propose an assessment framework addressing key steps in LCA, namely, goal definition, functional unit, baseline versus alternative scenario definition, and modeling of system responses. Regulatory and economic aspects (e.g., trends in consumption patterns, market responses, market saturation, and legislative side-policies affecting waste management) are emphasized as critical for the identification of potential system responses and for supporting regulatory interventions required to reach the intended environmental benefits. The framework is recommended for LCA studies focusing on system-wide consequences where allocation between product life cycles is not relevant; however, the framework can be adapted to include allocation. The application of the framework was illustrated by an example of implementing a policy target for 2025 of 70% recycled content in PET trays in EU27+1. It was demonstrated that neglecting large-scale market responses and saturation lead to an overestimation of the environmental benefits from the policy target and that supplementary initiatives are required to achieve the full benefits at system level.
|
|
| 19. |
- Arvidsson, Rickard, 1984, et al.
(författare)
-
Using industrial default values for prospective modeling of new materials production – the case of photon upconversion materials for solar modules
- 2021
-
Konferensbidrag (övrigt vetenskapligt/konstnärligt)abstract
- Several approaches to upscaling of materials production processes in the context of prospective life cycle assessment (LCA) have been proposed. Often, such approaches are bottom-up, departing from laboratory-scale descriptions of production processes and from that creating a model of future large-scale production. While such approaches make use of the material-specific knowledge available at the time of the assessment, they often neglect emergent aspects that may be present at factory level. An alternative, more top-down approach is to use industrial default values, i.e. average or typical values of inputs and outputs reflecting materials production today. Since production facilities normally do not change drastically over at least 10 years, such values might be relevant in prospective LCAs, at least given modest time horizons. Such default values can also be modified based on assumptions about future changes, such as increased energy recovery or novel solvent recovery processes. We applied previously derived industrial default values for fine chemical production when modeling the production of two materials with potential use in photon upconversion applications: lead sulfide (PbS) and lead selenide (PbSe) nanoparticles. Photon upconversion means that two low-energy photons are converted into one higher-energy photon utilizable by a solar module. While we used some material-specific values, such as synthesis-specific yields, most auxiliary input and output values (e.g. solvents, inert gas, heat, electricity and emissions) instead represent factory-scale values for current fine chemical production. Considering the availability of both best- and worst-case default values, it was possible to derive ranges for the likely future environmental impacts of the two materials. We conclude that the approach is feasible, but the availability of more up-to-date industrial default values would make it even more relevant in prospective LCAs.
|
|
| 20. |
- Baldi, Francesco, et al.
(författare)
-
The cost of innovative and sustainable future ship energy systems
- 2019
-
Ingår i: ECOS 2019 - Proceedings of the 32nd International Conference on Efficiency, Cost, Optimization, Simulation and Environmental Impact of Energy Systems. ; , s. 239-250
-
Konferensbidrag (refereegranskat)abstract
- The latest guidelines approved by the environmental protection committee of the international maritime organization (IMO) will require the shipping sector to reduce its greenhouse gas (GHG) emissions by 50% before 2050 and achieve a complete decarbonization by the end of the century. This will require a major change in the way ships are built and operated today. In this paper, we aim at understanding what types of ship energy systems and fuels will be preferable and what will be the costs to achieve the environmental goals set by IMO for shipping. To do this, we approach the question as an MILP problem, with increasingly stringent constraints on the total GHG emissions and with the objective of minimizing the total cost of ownership. We apply this analysis to three ship types (a containership, a tanker, and a passenger ferry) and we determine what type of choice for the ship’s energy systems will be the most optimal, for each ship type. The results show that the most cost-effective pathway towards the elimination of GHG emissions is composed of a first phase with LNG as fuel and with an increasing use of carbon capture and storage, while the full decarbonisation of the shipping sector will require switching to hydrogen as fuel. These results depend only marginally on the type of ship investigated and on the type of regulation enforced. While the costs required to achieve up to 75% GHG emission reduction are relatively similar to the baseline case (50-70% higher), moving towards a full decarbonisation will require a cost increase ranging between 280% and 340% higher than the business as usual.
|
|
