| 1. |
- Adegoke, Olutayo, et al.
(author)
-
Scanning electron microscopy and atom probe tomography characterization of laser powder bed fusion precipitation strengthening nickel-based superalloy
- 2023
-
In: Micron. - 0968-4328 .- 1878-4291. ; 171
-
Journal article (peer-reviewed)abstract
- Atom probe tomography (APT) was utilized to supplement scanning electron microscopy (SEM) characterizationof a precipitation strengthening nickel-based superalloy, Alloy 247LC, processed by laser powder bed fusion (LPBF). It was observed that the material in the as-built condition had a relatively high strength. Using both SEMand APT, it was concluded that the high strength was not attributed to the typical precipitation strengtheningeffect of γ’. In the absence of γ’ it could be reasonably inferred that the numerous black dots observed in thecells/grains with SEM were dislocations and as such should be contributing significantly to the strengthening.Thus, the current investigation demonstrated that relatively high strengthening can be attained in L-PBF even inthe absence of precipitated γ’. Even though γ’ was not precipitated, the APT analysis displayed a nanometer scalepartitioning of Cr that could be contributing to the strengthening. After heat-treatment, γ’ was precipitated and itdemonstrated the expected high strengthening behavior. Al, Ta and Ti partitioned to γ’. The strong partitioningof Ta in γ’ is indicative that the element, together with Al and Ti, was contributing to the strain-age crackingoccurring during heat-treatment. Cr, Mo and Co partitioned to the matrix γ phase. Hf, Ta, Ti and W were found inthe carbides corroborating previous reports that they are MC.
|
|
| 2. |
- Andersson, Joel, 1981-, et al.
(author)
-
Effect of Different Solution Heat Treatments on the Hot Ductility of Superalloys : Part 3 - Waspaloy
- 2013
-
In: Materials Science and Technology. - 0267-0836 .- 1743-2847. ; 29:1, s. 43-53
-
Journal article (peer-reviewed)abstract
- The susceptibility to heat affected zone cracking of Waspaloy has been investigated in terms of its hot ductility, measured as the reduction of area (RA). Gleeble testing with on-heating as well as on-cooling test cycles was carried out to illuminate the influence of different 4 h solution heat treatments between 996 and 1080°C. A ductility maximum of between 80 and 90%RA was found at 1050–1100°C for all conditions in the on-heating tests. Although the different heat treatment conditions showed similar macrohardness, the particle size and distribution of the γ′ and M23C6 phases differed, which significantly affected the on-heating ductility in the lower temperature test region. The ductile to brittle transition was initiated at 1100°C in the on-heating testing with indications of grain boundary liquation at the higher test temperatures. Ductility recovery, as measured in the on-cooling tests from 1240°C, was very limited with <30%RA for all conditions and test temperatures except for the 1080°C/4 h treatment, which exhibited 60%RA at 980°C.
|
|
| 3. |
- Andersson, Joel Håkan, 1981, et al.
(author)
-
Effect of different solution heat treatments on hot ductility of superalloys Part 2-Allvac 718Plus
- 2012
-
In: Materials Science and Technology. - : Taylor & Francis Group. - 1743-2847 .- 0267-0836. ; 28:6, s. 733-741
-
Journal article (peer-reviewed)abstract
- The hot ductility of Allvac 718Plus for different solution heat treatments (954 degrees C-15 h, 954 degrees C-1 h, 982 degrees C-1 h and 1050 degrees C-3 h+954 degrees C-1 h) has been investigated using Gleeble testing. Substantial variations in the microstructure among the heat treatments affected the Gleeble test hot ductility only to a very limited extent. Constitutional liquation of the NbC phase was found to be the main cause for the poor ductility at high testing temperatures in the on-heating cycle as well as at the lower temperatures on-cooling. Grain boundary delta phase was seen to assist the constitutional liquation of the NbC phase. Based on established evaluation criteria for Gleeble ductility testing, a ranked indicator for weldability is suggested.
|
|
| 4. |
- Andersson, Joel Håkan, 1981, et al.
(author)
-
Investigation of Homogenization and its Influence on the Repair Welding of Cast Allvac 718Plus
- 2010
-
In: Proceedings of The 7th International Symposium on Superalloy 718 and Derivatives, TMS (The Minerals, Metals and Materials Society). - Hoboken, NJ, USA : John Wiley & Sons, Inc.. - 9781617827709 ; , s. 439-454, s. 439-454
-
Conference paper (peer-reviewed)abstract
- Heat treatment experiments have been carried out to bring understanding to the efficacy of different temperatures and dwell times on the degree of homogenization of the cast Allvac 718Plus alloy which is prone to segregation mainly due to its high content of niobium. The effect of homogenization on weld repair was also examined. The homogenization heat treatment temperatures ranged from 1050°C to 1200°C with 1hr, 5 hrs and 10 hrs dwell times. The degree of homogenization was measured as the reduction of the amount of Laves phase by manual point counting in an optical microscope at high magnification. Longer range, interdendritic, patterns were established through line scan EDS analysis in SEM. It was found that short time (1hr) does not significantly reduce the amount of Laves phase whereas 5 hrs and 10hrs are much more efficient. Interdendritic homogenization does not occur to any measurable extent even at the highest temperature and longest dwell time (1200°C-10hrs) which was also reflected in bulk macro Vickers hardness tests.In the weld repair tests, one of the most homogenized material conditions (1125°C-5hrs +1200°C-10hrs) turned out to be the most prone to cracking while the number of weld cracks after a moderate homogenization heat treatment (1125°C-5hrs) was much smaller .
|
|
| 5. |
- Andersson, Joel, 1981-, et al.
(author)
-
Hot Cracking of Allvac 718Plus, Alloy 718 and Waspaloy at Varestraint Testing
- 2008
-
In: 4th International Symposium on Aerospace Materials and Manufacturing Processes. - Montreal : Canadian Institute of Mining, Metallurgy and Petroleum. - 9781617386169 ; , s. 401-413, s. 401-413
-
Conference paper (peer-reviewed)abstract
- Varestraint testing together with DSC and SEM-EDX analyses have been performed as means of investigating the hot cracking susceptibility of Allvac 718Plus, alloy 718 and Waspaloy. The solidification sequences in Allvac 718Plus and alloy 718 were very similar to each other starting by an initial solidification of the gamma phase, gamma/MC reaction at around 1260°C and then finally ending the sequence by gamma/Laves eutectic reaction at around 1150°C. Waspaloy had the same solidification sequence, except no Laves phase formation takes place, and solidification started at a somewhat higher temperature as compared to alloy 718 and the solidification sequence ends by a gamma/MC reaction at around 1245°C. The total amount of hot cracking in Waspaloy was shown to be much less than that in alloy 718 and in Allvac 718Plus which is believed to be related to the presence of the Laves eutectic in the latter two alloys with corresponding larger solidification ranges. Hot cracking of 718Plus is slightly less than in 718.
|
|
| 6. |
- Andersson, Joel, 1981-, et al.
(author)
-
Hot Ductility Study of Haynes 282 Superalloy
- 2010
-
In: Superalloy 718 and Derivatives. - Hoboken, NJ, USA : The Minerals, Metals, and Materials Society. - 9780470943168 ; , s. 539-554, s. 539-554
-
Conference paper (peer-reviewed)
|
|
| 7. |
- Andersson, Joel, 1981-, et al.
(author)
-
Metallurgical Response of Electron Beam Welded Allvac® 718Plus™
- 2011
-
In: Hot Cracking Phenomena in Welds III. - Berlin, Heidelberg : Springer Berlin/Heidelberg. - 9783642168635 ; , s. 415-428, s. 415-428
-
Conference paper (peer-reviewed)abstract
- Electron beam welding of forged Allvac 718Plus superalloy has been carried out without any visible cracks in weld cross-sections. Healed cracks in the heat affected zone were, however, seen in most cross-sections with the healing as well as the cracking believed to be due to the constitutional liquation of the δ-phase. The δ-phase undergoes constitutional liquation in the Heat Affected Zone (HAZ) and consequently decreases the ductility of the material and renders cracks in the HAZ but due to the large amount of eutectic liquid produced at the same time the healing of the opened cracks takes place.
|
|
| 8. |
|
|
| 9. |
- Aryal, Pradip, et al.
(author)
-
Comparative study of the main electromagnetic models applied to melt pool prediction with gas metal arc : Effect on flow, ripples from drop impact, and geometry
- 2022
-
In: International Journal of Heat and Mass Transfer. - : Elsevier. - 0017-9310 .- 1879-2189. ; 194
-
Journal article (peer-reviewed)abstract
- The present work concerns the electromagnetic force models in computational fluid dynamics simulations of melt pools produced with electric arcs. These are commonly applied to gas metal arcs with metal transfer, in welding and additive manufacturing. Metal drop impact on the melt pool is thus included in this study. The electromagnetic force models applied in literature use either numerical solutions of Poisson equations or one of the two analytical models developed by Kou and Sun, or Tsao and Wu. These models rely on assumptions for which the effect on the melt pool predictions remains to be understood. The present work thoroughly investigates those assumptions and their effects. It has been supported by dedicated experimental tests that did provide estimates of unknown model parameters and validation data. The obtained results show that the assumptions that fundamentally distinguish these three models change the electromagnetic force, including the relation between its components. These changes, which can also be spatially non-uniform, are large. As a result, these models lead to significantly different recirculation flow pattern, thermal convection, melt pool morphology, bead dimensions, and free surface response to the metal transfer. We conclude by proposing conditions in which each of these models is suited or questionable.
|
|
| 10. |
- Aryal, Pradip, et al.
(author)
-
Effect of Substrate Orientation on Melt Pool during Multi-Layer Deposition in V-Groove with Gas Metal Arc
- 2021
-
In: Proceedings of the World Congress on Mechanical, Chemical, and Material Engineering. - : Avestia Publishing. - 2369-8136. - 9781927877616
-
Conference paper (peer-reviewed)abstract
- Thermo-fluid dynamic and experimental approaches are used to investigate the influence of 20° uphill, downhill and sideway substrate orientation during metal deposition over a previously deposited bead in a V-groove. The computational fluid dynamic model with free surface deformation and metal transfer gives insight into the melt pool flow and causes of defect formation observed on the solidified beads. The experimental metallographs, high-speed images and computational results show good agreement. It is found that the deposition of a second layer on a smooth first layer cooled down to room temperature leads to large changes in melt pool flow pattern at 20° substrate inclination compared to flat condition. It results in undercut and humps with the uphill orientation and undercut with the side inclination. Therefore, lower angle range is necessary for multilayer gas metal arc deposition for these two last configurations.
|
|
