| 51. |
|
|
| 52. |
|
|
| 53. |
|
|
| 54. |
- Gustavsson, Eva, et al.
(författare)
-
Evaluation of Aerodynamic Particle Sizer and Electrical Low-Pressure Impactor for Unimodal and Bimodal Mass-Weighted Size Distributions
- 2005
-
Ingår i: Aerosol Science and Technology. - : Taylor and Francis Ltd. - 0278-6826 .- 1521-7388. ; 39:9, s. 871-887
-
Tidskriftsartikel (refereegranskat)abstract
- The objective of this study was to investigate the feasibility of the Aerodynamic Particle Sizer (APS) and the Electrical Low-Pressure Impactor (ELPI) to study mass weighted particle size distributions. Unimodal and bimodal liquid test aerosols were produced to a small chamber. Simultaneous measurements were performed with an APS 3320, an APS 3321, an ELPI and a Dekati Low-Pressure Impactor (DLPI) analyzed gravimetrically. ELPI current and mass responses were simulated for lognormal size distributions using a parameterization of the impactor kernel functions. In experiments with a single coarse mode, the mass ratio to the DLPI was between 0.75 and 1.15 for both APS models up to 5 µ m and for the ELPI up to 3 µ m. For larger sizes the ELPI and APS 3320 overestimated and the APS 3321 underestimated the concentration. In experiments with a single fine mode, submicrometer ELPI and DLPI results were in good agreement. However, in contrast to the DLPI all three spectrometers showed a significant mass fraction above 1 µ m. In experiments with a bimodal size distribution, the mass ratios were altered compared to single coarse mode experiments. Simulations showed that uncertainties in ELPI measurements of larger particles occur when concentrations of small particles are high. Several mechanisms that may bias ELPI and APS measurements are described. With knowledge of these, ELPI and APS 3321 can, under many circumstances give accurate time-resolved mass size distributions for particles smaller than 3 and 5 µm, respectively.
|
|
| 55. |
- Gäfvert, Torbjörn, et al.
(författare)
-
Thorium exposure during tungsten inert gas welding with thoriated tungsten electrodes
- 2003
-
Ingår i: Radiation Protection Dosimetry. - 1742-3406. ; 103:4, s. 349-357
-
Tidskriftsartikel (refereegranskat)abstract
- The exposure to Th-232 from TIG welding with thoriated electrodes has been determined at five different workshops. Welding with both alternating and direct current was investigated. The exposure levels of Th-232 were generally below 10 mBq m(-3) in the breathing zone of the welders. Two samples from AC welding showed significant higher exposure levels, probably due to maladjustment of the TIG welding power source. Samples of the respirable fraction of Th-232 from grinding thoriated electrodes were also collected showing exposure levels of 5 mBq m(-3) or lower. A dose estimate has been made for two scenarios, one realistic and one with conservative assumptions, showing that the annual committed effective dose from inhalation of Th-232, Th-230, Th-228 and Ra-228, for a full-time TIG welder, in the realistic case is below 0.3 mSv and with conservative assumptions around 1 mSv or lower. The contribution from grinding electrodes was lower, 10 muSv or lower in the realistic case and 63 muSv or lower based on conservative assumptions. The study does not exclude occurrence of higher exposure levels under welding conditions different from those prevailing in this study.
|
|
| 56. |
- Hagerman, Inger, et al.
(författare)
-
Effects on heart rate variability by artificially generated indoor nano-sized particles in a chamber study
- 2014
-
Ingår i: Atmospheric Environment. - : Elsevier BV. - 1352-2310. ; 88, s. 165-171
-
Tidskriftsartikel (refereegranskat)abstract
- Background: Airborne particles are associated with increased morbidity and mortality due to respiratory and cardiovascular diseases in polluted areas. There is a growing interest in nano-sized particles with diameter < 100 nm and their potential health effects. Heart rate variability (HRV) is a noninvasive method for cardiovascular risk prediction in high prevalent groups. Aim of study: The aim was to evaluate the impact of nano-sized indoor air particles on HRV for healthy and adult females. Methods: All exposures were performed as controlled chamber experiments with particle exposure from burning candles, terpene + ozone reactions or filtered air in a double-blind cross over design. Twenty-two healthy females were investigated during 10 min periods at different exposures and the reactivity in high frequency (HF) spectral band of HRV were computed. Results: Heart rate was unchanged from baseline values in all groups during all experimental settings. HF power of HRV tended to increase during exposure to particles from burning candle while particles from terpene + ozone reactions tended to decrease HF power. Conclusions: Exposure to nano-sized particles of burning candles or terpene + ozone reactions results in different patterns of heart rate variability, with signs of altered autonomic cardiovascular control. Practical implications: This study indicates that the HRV method may be used for information on physiological responses of exposure to different nano-sized particles and contribute to the understanding of mechanisms behind health effects of particle exposures. (C) 2014 The Authors. Published by Elsevier Ltd.
|
|
| 57. |
|
|
| 58. |
|
|
| 59. |
|
|
| 60. |
- Hedmer, Maria, et al.
(författare)
-
Exposure and Emission Measurements During Production, Purification, and Functionalization of Arc-Discharge-Produced Multi-walled Carbon Nanotubes.
- 2014
-
Ingår i: Annals of Occupational Hygiene. - : Oxford University Press (OUP). - 1475-3162. ; 58:3, s. 355-379
-
Tidskriftsartikel (refereegranskat)abstract
- Background: The production and use of carbon nanotubes (CNTs) is rapidly growing. With increased production, there is potential that the number of occupational exposed workers will rapidly increase. Toxicological studies on rats have shown effects in the lungs, e.g. inflammation, granuloma formation, and fibrosis after repeated inhalation exposure to some forms of multi-walled CNTs (MWCNTs). Still, when it comes to health effects, it is unknown which dose metric is most relevant. Limited exposure data for CNTs exist today and no legally enforced occupational exposure limits are yet established. The aim of this work was to quantify the occupational exposures and emissions during arc discharge production, purification, and functionalization of MWCNTs. The CNT material handled typically had a mean length <5 μm. Since most of the collected airborne CNTs did not fulfil the World Health Organization fibre dimensions (79% of the counted CNT-containing particles) and since no microscopy-based method for counting of CNTs exists, we decided to count all particle that contained CNTs. To investigate correlations between the used exposure metrics, Pearson correlation coefficient was used.
|
|
