| 1. |
- Abu-Ghaida, Haitham, et al.
(författare)
-
Accounting for product recovery potential in building life cycle assessments: a disassembly network-based approach
- 2024
-
Ingår i: International Journal of Life Cycle Assessment. - 1614-7502 .- 0948-3349. ; In Press
-
Tidskriftsartikel (refereegranskat)abstract
- Purpose: Existing life cycle assessment (LCA) methods for buildings often overlook the benefits of product recovery potential, whether for future reuse or repurposing. This oversight arises from the limited scope of such methods, which often ignore the complex interdependencies between building products. The present paper, backed by its supplementary Python library, introduces a method that addresses this gap, emphasizing the influence of product interdependencies and future recovery potential on environmental impact. Methods: Implementing the proposed method requires adding a phase, the recovery potential assessment, to the four phases that constitute an LCA according to the ISO 14040/14044 guidelines. Given the disassembly sequence for each product, in the first step of the recovery potential assessment, a disassembly network (DN) is created that displays structural and accessibility dependencies. By calculating the average of the disassembly potential (DP) of each structural dependency (second step) associated with that product, we obtain the DP (0.1–1) at the product level in a third step. Because there is no empirical data available to support a specific relationship between product disassembly potential and recovery potential (RP) (0–1), we employ, in a fourth step, a flexible model specification to represent scenarios of how this relationship may look like. Ultimately, for each scenario, the resulting RP is used to enable a probabilistic material flow analysis with a binary outcome, whether to be recovered or not. The resulting product-level median material flows are then used to quantify the building’s environmental impact for a given impact category in the life cycle impact assessment (LCIA). The results are interpreted through an uncertainty, hotspot, and sensitivity analysis. Results and discussion: Our results show that not considering the interdependencies between building products in building LCAs results in underestimating the embodied greenhouse gas (GHG) emissions by up to 28.29%. This discrepancy is primarily attributed to a failure to account for additional material flows stemming from secondary replacements owing to the interdependencies during the life cycle. When accounting for end-of-life recovery benefits, a zero-energy building (ZEB) design incorporating some DfD principles demonstrated up to 45.94% lower embodied GHG emissions than the ZEB design with low disassembly potential when assuming that recovered products will be reused. Conclusions: Our approach provides first-of-a-kind evidence that not accounting for recovery potential may significantly distort the results of an LCA for buildings. The method and its supporting code support the semi-automated calculation of the otherwise neglected potential environmental impact, thus helping to drive the transition towards a more sustainable built environment. The supporting code allows researchers to build on the proposed framework if more data on the relationship between DP and RP become available in the future. Finally, while applied to buildings in this paper, the proposed framework is adaptable to any complex product with limited modifications in the supporting code.
|
|
| 2. |
- Adrianto, Lugas Raka, et al.
(författare)
-
How can LCA include prospective elements to assess emerging technologies and system transitions? The 76th LCA Discussion Forum on Life Cycle Assessment, 19 November 2020
- 2021
-
Ingår i: International Journal of Life Cycle Assessment. - : Springer Science and Business Media LLC. - 1614-7502 .- 0948-3349. ; 26:8, s. 1541-1544
-
Tidskriftsartikel (refereegranskat)abstract
- This paper summarizes the 76th LCA Discussion Forum end its main findings. Main issues when addressing emerging technologies identified were: the lack of primary data, the need for (shared) future background scenarios and (guidlines for) a common methodology. The following recommendations have been derived by the organizers: 1) Specific foreground inventories are always tailor-made, but consistency can be improved through lists of mandatory considerations. 2) Continue sharing (future) technology data and proxy processes, that can be readily replicated to new studies and assist in developing inventories. 3) Streamline and unify the process of including scenarios for background systems. New approaches may provide first important solutions to efficiently include consistent future scenarios in prospective LCA.
|
|
| 3. |
- Aggarwal, Rahul, 1994, et al.
(författare)
-
Influence of data selection on aquatic ecotoxicity characterization factors for selected persistent and mobile substances
- 2024
-
Ingår i: International Journal of Life Cycle Assessment. - Göteborg : IVL Svenska Miljöinstitutet AB. - 1614-7502 .- 0948-3349. ; 29:2, s. 344-354
-
Tidskriftsartikel (refereegranskat)abstract
- Purpose: This paper addresses the lack of ecotoxicity characterization factors (CFs) for persistent and mobile (PM) chemicals in life cycle assessment. The specific aims are (1) to provide CFs for 64 selected chemicals and benchmark them against the USEtox database, (2) to propose an ecotoxicity data harmonization strategy, and (3) to analyze the influence of ecotoxicity data sources and data harmonization strategies. Methods: Sixty-four per- and polyfluoroalkyl substances (PFAS), triazines, and triazoles were selected. An ecotoxicity data harmonization strategy was developed to ensure data consistency. A screening strategy for including transformation products was also developed. Existing CFs in the USEtox organic substances database (version 2.01) were identified, and new CFs were calculated based on available data sources. The USEtox model (version 2.13) was used for calculations, and the collected ecotoxicity data from different sources were varied to test their influence. Results and discussion: The ecotoxicity data harmonization strategy excluded a considerable amount of incompatible data. To the list of 64 chemicals, 3 transformation products were added. Out of the 67 chemicals, experimental ecotoxicity data were available for 47, leading to the use of in silico tools and average values to fill data gaps for 20 chemicals. CFs for 67 chemicals could thus be provided. Comparing CFs calculated based on experimental and estimated ecotoxicity data reveals that the estimated data leads to considerably different CF values. Conclusions: The paper provides strategies for ecotoxicity data harmonization and the inclusion of transformation products. The limited availability of experimental ecotoxicity data and differing results of the applied estimation methods highlight the need for further development of estimation methods. In addition, further development in including transformation products is recommended, which is particularly relevant for PM chemicals.
|
|
| 4. |
- Ahmadi, Leila, et al.
(författare)
-
A cascaded life cycle: reuse of electric vehicle lithium-ion battery packs in energy storage systems
- 2017
-
Ingår i: The International Journal of Life Cycle Assessment. - : Springer Science and Business Media LLC. - 0948-3349 .- 1614-7502. ; 22:1, s. 111-124
-
Tidskriftsartikel (refereegranskat)abstract
- PurposeLithium-ion (Li-ion) battery packs recovered from end-of-life electric vehicles (EV) present potential technological, economic and environmental opportunities for improving energy systems and material efficiency. Battery packs can be reused in stationary applications as part of a “smart grid”, for example to provide energy storage systems (ESS) for load leveling, residential or commercial power. Previous work on EV battery reuse has demonstrated technical viability and shown energy efficiency benefits in energy storage systems modeled under commercial scenarios. The current analysis performs a life cycle assessment (LCA) study on a Li-ion battery pack used in an EV and then reused in a stationary ESS.MethodsA complex functional unit is used to combine energy delivered by the battery pack from the mobility function and the stationary ESS. Various scenarios of cascaded “EV mobility plus reuse in stationary clean electric power scenarios” are contrasted with “conventional system mobility with internal combustion engine vehicles plus natural gas peaking power.” Eight years are assumed for first use; with 10 years for reuse in the stationary application. Operational scenarios and environmental data are based on real time-of-day and time-of-year power use. Additional data from LCA databases are utilized. Ontario, Canada, is used as the geographic baseline; analysis includes sensitivity to the electricity mix and battery degradation. Seven environmental categories are assessed using ReCiPe.Results and discussionResults indicate that the manufacturing phase of the Li-ion battery will still dominate environmental impacts across the extended life cycle of the pack (first use in vehicle plus reuse in stationary application). For most impact categories, the cascaded use system appears significantly beneficial compared to the conventional system. By consuming clean energy sources for both use and reuse, global and local environmental stress reductions can be supported. Greenhouse gas advantages of vehicle electrification can be doubled by extending the life of the EV batteries, and enabling better use of off-peak low-cost clean electricity or intermittent renewable capacity. However, questions remain concerning implications of long-duration use of raw material resources employed before potential recycling.ConclusionsLi-ion battery packs present opportunities for powering both mobility and stationary applications in the necessary transition to cleaner energy. Battery state-of-health is a considerable determinant in the life cycle performance of a Li-ion battery pack. The use of a complex functional unit was demonstrated in studying a component system with multiple uses in a cascaded application.
|
|
| 5. |
- Almeida, Cheila, et al.
(författare)
-
Environmental assessment of sardine (Sardina pilchardus) purse seine fishery in Portugal with LCA methodology including biological impact categories
- 2014
-
Ingår i: The International Journal of Life Cycle Assessment. - : Springer Science and Business Media LLC. - 0948-3349 .- 1614-7502. ; 19:2, s. 297-306
-
Tidskriftsartikel (refereegranskat)abstract
- Purpose: The purse seine fishery for sardine is the most important fishery in Portugal. The aim of the present study is to assess the environmental impacts of sardine fished by the Portuguese fleet and to analyse a number of variables such as vessel size and time scale. An additional goal was to incorporate fishery-specific impact categories in the case study. Methods: Life Cycle Assessment methodology was applied, and data were collected from nine vessels, which represented around 10 % of the landings. Vessels were divided into two length categories, above and below 12 m, and data were obtained for the years 2005 to 2010. The study was limited to the fishing phase only. The standard impact categories included were energy use, global warming potential, eutrophication potential, acidification potential and ozone depletion potential. The fishery-specific impact categories were overfishing, overfishedness, lost potential yield, mean trophic level and the primary production required, and were quantified as much as possible. Results and discussion: The landings from the data set were constituted mainly by sardine (91 %), and the remainders were other small pelagic species (e.g. horse mackerel). The most important input was the fuel, and both vessel categories had the same fuel consumption per catch 0.11 l/kg. Average greenhouse gas emissions (carbon footprint) were 0.36 kg CO2 eq. per kilo sardine landed. The fuel use varied between years, and variability between months can be even higher. Fishing mortality has increased, and the spawning stock biomass has decreased resulting in consequential overfishing for 2010. A correlation between fuel use and stock biomass was not found, and the stock condition does not seem to directly influence the global warming potential in this fishery. Discards were primarily non-target small pelagic species, and there was also mortality of target species resulting from slipping. The seafloor impact was considered to be insignificant due to the fishing method. Conclusions: The assessment of the Portuguese purse seine fishery resulted in no difference regarding fuel use between large and small vessels, but differences were found between years. The stock has declined, and it has produced below maximum sustainable yield. By-catch and discard data were missing but may be substantial. Even being difficult to quantify, fishery impact categories complement the environmental results with biological information and precaution is need in relation to the stock management. The sardine carbon footprint from Portuguese purse seine was lower than that of other commercial species reported in.
|
|
| 6. |
|
|
| 7. |
- Alvarez-Gaitan, JP, et al.
(författare)
-
Consequential cradle-to-gate carbon footprint of water treatment chemicals using simple and complex marginal technologies for electricity supply
- 2014
-
Ingår i: International Journal of Life Cycle Assessment. - : Springer Science and Business Media LLC. - 1614-7502 .- 0948-3349. ; 19:12, s. 1974-1984
-
Tidskriftsartikel (refereegranskat)abstract
- Purpose Chemicals produced via chlor-alkali electrolysis arewidely used throughout the water industry worldwide, withtreatment chemicals often the second largest source of environmental impacts from potable water production after electricity use. Population-driven increases in the future demand for potable water will require concomitant increases in the production of water treatment chemicals, with the associated environmental impacts of chemicals production primarily arising from the additional demand for electricity. Due to the dominance of electricity in the environmental performance of chlor-alkali chemicals, assessment of the future environmental impacts of potable water production is largely dependent on proper identification of the marginal source of electricity. Inthis paper, we present a consequential cradle-to-gate carbonfootprint (cCF) for the most widely used chlor-alkali produced disinfectant (sodium hypochlorite (13 % w/w)) andcoagulant (ferric chloride (42 % w/w)) in Australia, withspecial emphasis placed upon the identification of futuremarginal electricity supply and the substitution of hydrogengas and sodium hydroxide during production. While thisanalysis is presented in an Australian context, commonalities in potable water and chlor-alkali chemical production processes internationally give the findings a broader relevance.Methods Consequential models for sodium hypochlorite (13 % w/w) and ferric chloride (42 % w/w) production were developed, and the identification of the marginal source ofelectricity was modelled using a “simple marginal technology” approach via operationalisation of the Weidema framework and a “complex marginal technology” using a partial equilibrium model. For the simple marginal technology, the levelised cost of electricity was used to select the most competitive energy generation technologies and those most relevant for the Australian market. For the complex marginal technology, the energy sector model was used to simulate the most likely electricity supply mix. Details of the different paths taken in the substitution of hydrogen gas and sodium hydroxide are also presented. To allow for proper incorporation of uncertainties arising from these key factors in the cCF, several scenarios were developed covering fuel and carbon prices for identifying the marginal supplymix of electricity, as well as the likely production routes for sodium carbonate in the context of sodium hydroxide substitution.Results and discussion cCF results of sodium hypochlorite(13%w/w) and ferric chloride (42%w/w) are presented usingsimple and complex marginal technologies, and the implications of choosing one marginal technology over the other in the context of water treatment chemicals are presented. For the simple marginal technology approach, the global warming potential (GWP) per megagram of chemical varied from 68 to 429 kg CO2-eq for sodium hypochlorite (13 % w/w) and 59–1,020 kg CO2-eq for ferric chloride (42 % w/w). For the complex marginal technology approach, the GWP per megagram of chemical varied from 266 to 332 kg CO2-eqfor sodium hypochlorite (13 % w/w) and 214–629 kg CO2-eqfor ferric chloride (42 % w/w). Insights are given in relation to the impact of the price of fossil fuels, the carbon price, and the different substitution routes.Conclusions The use of a partial equilibrium model (PEM) hasenabled a better understanding of the variability of the results in this study. For example, the use of PEM for the identification of the complex marginal source of electricity shows that, for the case of Australia, any benefit from a carbon price is lost with high prices of natural gas due to the incentive to use cheaper fuels such as black and brown coal. Likewise, the use of explorative scenarios was decisive to manage the inherent uncertainty of the parameters included in the model. In relation to substitution, the case of ferric chloride (42 % w/w) indicated that using only one substitution route was not enough to fully understand the potential continuum of cCF results. The simple marginal approach, where an exclusive marginal source of electricity or substitution route is considered, presents significant risks for the modelling accuracy of the cCF as shown here for sodium hypochlorite (13 % w/w) and ferric chloride (42 % w/w), therefore, it is not recommended.
|
|
| 8. |
- Alvarez-Gaitan, Juan P, et al.
(författare)
-
A hybrid life cycle assessment of water treatment chemicals: an Australian experience
- 2013
-
Ingår i: International Journal of Life Cycle Assessment. - : Springer Science and Business Media LLC. - 1614-7502 .- 0948-3349. ; 18:7, s. 1291-1301
-
Tidskriftsartikel (refereegranskat)abstract
- PurposeLife cycle assessment (LCA) of chemicals is usually developed using a process-based approach. In this paper, we develop a tiered hybrid LCA of water treatment chemicals combining the specificity of process data with the holistic nature of input–output analysis (IOA). We compare these results with process and input–output models for the most commonly used chemicals in the Australian water industry to identify the direct and indirect environmental impacts associated with the manufacturing of these materials.MethodsWe have improved a previous Australian hybrid LCA model by updating the environmental indicators and expanding the number of included industry sectors of the economy. We also present an alternative way to estimate the expenditure vectors to the service sectors of the economy when financial data are not available. Process-based, input–output and hybrid results were calculated for caustic soda, sodium hypochlorite, ferric chloride, aluminium sulphate, fluorosilicic acid, calcium oxide and chlorine gas. The functional unit is the same for each chemical: the production of 1 tonne in the year 2008.Results and discussionWe have provided results for seven impact categories: global warming potential; primary energy; water use; marine, freshwater and terrestrial ecotoxicity potentials and human toxicity potential. Results are compared with previous IOA and hybrid studies. A sensitivity analysis of the results to assumed wholesale prices is included. We also present insights regarding how hybrid modelling helps to overcome the limitations of using IO- or process-based modelling individually.Conclusions and recommendationsThe advantages of using hybrid modelling have been demonstrated for water treatment chemicals by expanding the boundaries of process-based modelling and also by reducing the sensitivity of IOA to fluctuations in prices of raw materials used for the production of these industrial commodities. The development of robust hybrid life cycle inventory databases is paramount if hybrid modelling is to become a standard practice in attributional LCA.
|
|
| 9. |
- Andersson, Karin, et al.
(författare)
-
Life cycle assessment of bread produced on different scales
- 1999
-
Ingår i: The International Journal of Life Cycle Assessment. - 0948-3349 .- 1614-7502 .- 0346-718X. ; 4:1, s. 25-40
-
Tidskriftsartikel (refereegranskat)abstract
- A case study of white bread has been carried out with the purpose of comparing different scales of production and their potential environmental effects. The scales compared are: home baking, a local bakery and two industrial bakeries with distribution areas of different sizes. Data from the three bakeries and their suppliers have been collected. The systems investigated include agricultural production, milling, baking, packaging, transportation, consumption and waste management. Energy use and emissions have been quantified and the potential contributions to global warming, acidification, eutrophication and photo-oxidant formation have been assessed. The large industrial bakery uses more primary energy and contributes more to global warming, acidification and eutrophication than the other three systems. The home baking system shows a relatively high energy requirement; otherwise, the differences between home baking, the local bakery and the small industrial bakery are too small to be significant.
|
|
| 10. |
|
|
