| 1. |
- Appelgren, Patrik, et al.
(författare)
-
Disruption mechanisms in electrified solid copper jets
- 2011
-
Ingår i: Journal of applied mechanics. - : ASME International. - 0021-8936 .- 1528-9036. ; 78:2
-
Tidskriftsartikel (refereegranskat)abstract
- Interaction between a solid copper jet and an electric current pulse is a complex process that has been experimentally studied by letting a jet created by a shaped charge device pass through an electrode configuration consisting of two aluminum plates with a separation distance of 150 mm. When the jet bridged the electrodes, which are connected to a charged pulsed power supply, current pulses with amplitude up to 250 kA were passed through the jet. By using flash X-ray diagnostics, the disruption of the electrified jets could be studied. In this paper, the disruption of the electrified jets is discussed and compared with disruption phenomena observed in electrically exploded metal rods in a static setup. Necks are naturally formed along a stretching jet, and in the experiments with current interaction these necks explode electrically. In the static experiments, the metal rods have small notches distributed along the rod to resemble the necks of the jet. When two neighboring necks or notches explode, the shock of the explosion compresses the intermediate jet or rod segment axially and the material is forced out radially. The disruption phenomena in the jet and rod experiments are similar with rapid expansion of the metal at explosion and at comparable velocities.
|
|
| 2. |
- Appelgren, Patrik, et al.
(författare)
-
Experimental Study of Electromagnetic Effects on Solid Copper Jets
- 2010
-
Ingår i: Journal of applied mechanics. - : ASME International. - 0021-8936 .- 1528-9036. ; 77:1, s. 011010-
-
Tidskriftsartikel (refereegranskat)abstract
- In this paper we present a study of the interaction between all electric current pulse and a solid copper jet. Experiments were performed using a dedicated pulsed power supply delivering a current pulse of such amplitude, rise little, and duration that the jet is efficiently affected. The copper jet was created by using a shaped charge warhead. All electrode configuration consisting of two aluminum plates with a separation distance of 150 mm was used. The discharge current pulse and the voltages at the capacitors and at the electrodes were measured to obtain data oil energy deposition in and the resistance of the jet and electrode contact region. X-ray diagnostics were used to radiograph the jet, and by analyzing the radiograph, the degree of disruption of the electrified jet could be obtained. It was found that a current pulse with an amplitude of 200-250 kA and a rise time of 16 mu s could strongly enhance the natural fragmentation of the jet. In this case, the initial electric energy was 100 kJ and about 90% of the electric energy was deposited in the jet and electrodes. At the exit of the electrode region, the jet fragments formed rings with a radial velocity of up to 200 m/s, depending oil the initial electric energy in the pulsed power supply. [DOI: 10.1115/1.3172251]
|
|
| 3. |
- Appelgren, Patrik, et al.
(författare)
-
Interaction between solid copper jets and powerful electrical current pulses
- 2011
-
Ingår i: Journal of applied mechanics. - : ASME International. - 0021-8936 .- 1528-9036. ; 78:2
-
Tidskriftsartikel (refereegranskat)abstract
- The interaction between a solid copper jet and an electric current pulse is studied. Copper jets that were created by a shaped-charge device were passed through an electrode configuration consisting of two aluminum plates with a separation distance of 150 mm. The electrodes were connected to a pulsed-power supply delivering a current pulse with amplitudes up to 250 kA. The current and voltages were measured, providing data on energy deposition in the jet and electrode contact region, and flash X-ray diagnostics were used to depict the jet during and after electrification. The shape of, and the velocity distributions along, the jet has been used to estimate the correlation between the jet mass flow through the electrodes and the electrical energy deposition. On average, 2.8 kJ/g was deposited in the jet and electrode region, which is sufficient to bring the jet up to the boiling point. A model based on the assumption of a homogenous current flow through the jet between the electrodes underestimates the energy deposition and the jet resistance by a factor 5 compared with the experiments, indicating a more complex current flow through the jet. The experimental results indicate the following mechanism for the enhancement of jet breakup. When electrified, the natural-formed necks in the jet are subjected to a higher current density compared with other parts of the jet. The higher current density results in a stronger heating and a stronger magnetic pinch force. Eventually, the jet material in the neck is evaporated and explodes electrically, resulting in a radial ejection of vaporized jet material.
|
|
| 4. |
- Appelgren, Patrik, et al.
(författare)
-
Modeling of a small helical magnetic flux compression generator
- 2008
-
Ingår i: IEEE Transactions on Plasma Science. - 0093-3813 .- 1939-9375. ; 36:5, s. 2662-2672
-
Tidskriftsartikel (refereegranskat)abstract
- In order to gain experience in explosive pulsed power and to provide experimental data as the basis for computer modeling, a small high-explosive-driven helical magnetic flux-compression generator (FCG) was designed at the Swedish Defence Research Agency. The generator, of which three have been built, has an overall length of 300 mm and a diameter of 70 mm. It could serve as the energy source in a pulse-forming network to generate high-power pulses for various loads. This paper presents a simulation model of this helical FCG. The model, which was implemented in Matlab-Simulink, uses analytical expressions for the generator inductance. The model of resistive losses takes into account the heating of the conductors and the diffusion of the magnetic field into the conductors. The simulation results are compared with experimental data from two experiments with identical generators but with different seed currents, influencing the resistive losses. The model is used to analyze the performance of the generator.
|
|
| 5. |
|
|
| 6. |
- Appelgren, Patrik, et al.
(författare)
-
Small Helical Magnetic Flux-Compression Generators : Experiments and Analysis
- 2008
-
Ingår i: IEEE Transactions on Plasma Science. - 0093-3813 .- 1939-9375. ; 36:5, s. 2673-2683
-
Tidskriftsartikel (refereegranskat)abstract
- In order to gain experience in explosive pulsed power and to provide experimental data for modeling, a small high-explosive-driven helical magnetic flux-compression generator (FCG) was designed at the Swedish Defence Research Agency (FOI). The generator, of which three have been built, has an overall length of 300 mm and a diameter of 70 mm. It could serve as the energy source in a pulse-forming network to generate high power pulses for various loads. This paper presents the design of, and tests with, this helical FCG. The generator had an initial inductance of 23 mu H and was operated into a load of 0.2 mu H. The generator is charged with 0.27 kg of high explosives (PBXN-5). Various types of diagnostics were used to monitor the operation of the generator, including current probes, optical fibers, and piezo gauges. With seed currents of 5.7 and 11.2 kA, final currents of 269 and 436 kA were obtained, corresponding to current amplification factors of 47 and 39. The peak of the current was reached about 30 mu s after the time of crowbar. The two generators showed only small losses in terms of 2 pi-clocking. Using signals from optical fibers, the deflection angle of the armature could be determined to be 10 degrees in good agreement with hydrodynamic simulations of the detonation process and the detonation velocity to be 8.7 km/s in agreement with tabulated value.
|
|
| 7. |
- Bao, Yupan, et al.
(författare)
-
Single-shot 3D imaging of hydroxyl radicals in the vicinity of a gliding arc discharge
- 2021
-
Ingår i: Plasma Sources Science and Technology. - : IOP Publishing. - 0963-0252 .- 1361-6595. ; 30:4
-
Tidskriftsartikel (refereegranskat)abstract
- Chemical processing by plasma is utilized in many applications. Plasma-related studies, however, are challenging to carry out due to plasmas' transient and unpredictable behavior, excessive luminosity emission, 3D complexity and aggressive chemistry and physiochemical interactions that are easily affected by external probing. Laser-induced fluorescence is a robust technique for non-intrusive investigations of plasma-produced species. The hydroxyl radical (OH) is an interesting molecule to target, as it is easily produced by plasmas in humid air. In this letter, we present 3D distributions of ground state OH radicals in the vicinity of a glow-type gliding arc plasma. Such radical distributions, with minimal plasma emission, are captured instantaneously in one single camera acquisition by combining structured laser illumination and a lock-in based imaging analysis method called FRAME. The orientation of the plasma discharge can be reconstructed from the 3D data matrix, which can then be used to calculate 2D distributions of ground state OH radicals in a plane perpendicular to the orientation of the plasma channel. Our results indicate that OH distributions around a gliding arc are strongly affected by gas dynamics. We believe that the ability to instantaneously capture 3D transient molecular distributions in a plasma discharge, with minimal plasma emission interference, will have a strong impact on the plasma community for in-situ investigations of plasma-induced chemistry and physics.
|
|
| 8. |
- Devotta, Ashwin Moris, 1984-, et al.
(författare)
-
A modified Johnson-Cook model for ferritic-pearlitic steel in dynamic strain aging regime
- 2019
-
Ingår i: Metals. - : MDPI. - 2075-4701. ; 9:5
-
Tidskriftsartikel (refereegranskat)abstract
- In this study, the flow stress behavior of ferritic-pearlitic steel (C45E steel) is investigated through isothermal compression testing at different strain rates (1 s-1, 5 s-1, and 60 s-1) and temperatures ranging from 200 to 700 °C. The stress-strain curves obtained from experimental testing were post-processed to obtain true stress-true plastic strain curves. To fit the experimental data to well-known material models, Johnson-Cook (J-C) model was investigated and found to have a poor fit. Analysis of the flow stress as a function of temperature and strain rate showed that among other deformation mechanisms dynamic strain aging mechanism was active between the temperature range 200 and 400 °C for varying strain rates and J-C model is unable to capture this phenomenon. This lead to the need to modify the J-C model for the material under investigation. Therefore, the original J-C model parameters A, B and n are modified using the polynomial equation to capture its dependence on temperature and strain rate. The results show the ability of the modified J-C model to describe the flow behavior satisfactorily while dynamic strain aging was operative. © 2019 by the authors. Licensee MDPI, Basel, Switzerland.
|
|
| 9. |
- Ehn, Andreas, et al.
(författare)
-
Setup for microwave stimulation of a turbulent low-swirl flame
- 2016
-
Ingår i: Journal of Physics D: Applied Physics. - : IOP Publishing. - 0022-3727 .- 1361-6463. ; 49:18
-
Tidskriftsartikel (refereegranskat)abstract
- An experimental setup for microwave stimulation of a turbulent flame is presented. A low-swirl flame is being exposed to continuous microwave irradiation inside an aluminum cavity. The cavity is designed with inlets for laser beams and a viewport for optical access. The aluminum cavity is operated as a resonator where the microwave mode pattern is matched to the position of the flame. Two metal meshes are working as endplates in the resonator, one at the bottom and the other at the top. The lower mesh is located right above the burner nozzle so that the low-swirl flame is able to freely propagate inside the cylinder cavity geometry whereas the upper metal mesh can be tuned to achieve good overlap between the microwave mode pattern and the flame volume. The flow is characterized for operating conditions without microwave irradiation using particle imaging velocimetry (PIV). Microwave absorption is simultaneously monitored with experimental investigations of the flame in terms of exhaust gas temperature, flame chemiluminescence (CL) analysis as well as simultaneous planar laser-induced fluorescence (PLIF) measurements of formaldehyde (CH2O) and hydroxyl radicals (OH). Results are presented for experiments conducted in two different regimes of microwave power. In the high-energy regime the microwave field is strong enough to cause a breakdown in the flame. The breakdown spark develops into a swirl-stabilized plasma due to the continuous microwave stimulation. In the low-energy regime, which is below plasma formation, the flame becomes larger and more stable and it moves upstream closer to the burner nozzle when microwaves are absorbed by the flame. As a result of a larger flame the exhaust gas temperature, flame CL and OH PLIF signals are increased as microwave energy is absorbed by the flame.
|
|
| 10. |
- Elfsberg, Mattias, et al.
(författare)
-
Experimental Studies of Anode and Cathode Materials in a Repetitive Driven Axial Vircator
- 2008
-
Ingår i: IEEE Transactions on Plasma Science. - 0093-3813 .- 1939-9375. ; 36, s. 688-693
-
Tidskriftsartikel (refereegranskat)abstract
- Repetitive use of a high-power microwave (HPM) radiation source implies strong erosion on cathode and anode materials. Electrode material endurance has been studied in a series of experiments with an axial vircator powered by a compact Marx generator. The Marx generator operated in a 10 Hz repetitive mode with a burst of ten pulses. Velvet and graphite was used as electron-emitting materials, and they showed markedly different pulse characteristics. Three different anode materials were used; stainless steel mesh, stainless steel wires and molybdenum wires, which all had different influence on the pulse characteristics.
|
|
