| 1. |
-
Overview of the JET results
- 2015
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 0029-5515 .- 1741-4326. ; 55:10
-
Tidskriftsartikel (refereegranskat)
|
|
| 2. |
- Abel, I, et al.
(författare)
-
Overview of the JET results with the ITER-like wall
- 2013
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 53:10, s. 104002-
-
Tidskriftsartikel (refereegranskat)abstract
- Following the completion in May 2011 of the shutdown for the installation of the beryllium wall and the tungsten divertor, the first set of JET campaigns have addressed the investigation of the retention properties and the development of operational scenarios with the new plasma-facing materials. The large reduction in the carbon content (more than a factor ten) led to a much lower Z(eff) (1.2-1.4) during L- and H-mode plasmas, and radiation during the burn-through phase of the plasma initiation with the consequence that breakdown failures are almost absent. Gas balance experiments have shown that the fuel retention rate with the new wall is substantially reduced with respect to the C wall. The re-establishment of the baseline H-mode and hybrid scenarios compatible with the new wall has required an optimization of the control of metallic impurity sources and heat loads. Stable type-I ELMy H-mode regimes with H-98,H-y2 close to 1 and beta(N) similar to 1.6 have been achieved using gas injection. ELM frequency is a key factor for the control of the metallic impurity accumulation. Pedestal temperatures tend to be lower with the new wall, leading to reduced confinement, but nitrogen seeding restores high pedestal temperatures and confinement. Compared with the carbon wall, major disruptions with the new wall show a lower radiated power and a slower current quench. The higher heat loads on Be wall plasma-facing components due to lower radiation made the routine use of massive gas injection for disruption mitigation essential.
|
|
| 3. |
- Romanelli, F, et al.
(författare)
-
Overview of the JET results
- 2011
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 51:9
-
Tidskriftsartikel (refereegranskat)abstract
- Since the last IAEA Conference JET has been in operation for one year with a programmatic focus on the qualification of ITER operating scenarios, the consolidation of ITER design choices and preparation for plasma operation with the ITER-like wall presently being installed in JET. Good progress has been achieved, including stationary ELMy H-mode operation at 4.5 MA. The high confinement hybrid scenario has been extended to high triangularity, lower ρ*and to pulse lengths comparable to the resistive time. The steady-state scenario has also been extended to lower ρ*and ν*and optimized to simultaneously achieve, under stationary conditions, ITER-like values of all other relevant normalized parameters. A dedicated helium campaign has allowed key aspects of plasma control and H-mode operation for the ITER non-activated phase to be evaluated. Effective sawtooth control by fast ions has been demonstrated with3He minority ICRH, a scenario with negligible minority current drive. Edge localized mode (ELM) control studies using external n = 1 and n = 2 perturbation fields have found a resonance effect in ELM frequency for specific q95values. Complete ELM suppression has, however, not been observed, even with an edge Chirikov parameter larger than 1. Pellet ELM pacing has been demonstrated and the minimum pellet size needed to trigger an ELM has been estimated. For both natural and mitigated ELMs a broadening of the divertor ELM-wetted area with increasing ELM size has been found. In disruption studies with massive gas injection up to 50% of the thermal energy could be radiated before, and 20% during, the thermal quench. Halo currents could be reduced by 60% and, using argon/deuterium and neon/deuterium gas mixtures, runaway electron generation could be avoided. Most objectives of the ITER-like ICRH antenna have been demonstrated; matching with closely packed straps, ELM resilience, scattering matrix arc detection and operation at high power density (6.2 MW m-2) and antenna strap voltages (42 kV). Coupling measurements are in very good agreement with TOPICA modelling. © 2011 IAEA, Vienna.
|
|
| 4. |
- Litnovsky, A., et al.
(författare)
-
Overview of material migration and mixing, fuel retention and cleaning of ITER-like castellated structures in TEXTOR
- 2011
-
Ingår i: Journal of Nuclear Materials. - : Elsevier BV. - 0022-3115 .- 1873-4820. ; 415:1, s. S289-S292
-
Tidskriftsartikel (refereegranskat)abstract
- Plasma-facing components (PFCs) in ITER will be castellated by splitting them into small-size blocks to maintain the thermo-mechanical stability. However, there are concerns in particular on retention of codeposited radioactive fuel in the gaps. An R&D program is underway in TEXTOR addressing this acute issue of castellation. Material migration and fuel inventory are investigated using long- and short-term discharge-resolved experiments with castellated structures in TEXTOR. Significant impurity transport to the gaps was detected and results were in part quantitatively reproduced with 3D-GAPS code. Deposits containing up to 70 at.% of tungsten on the gap areas closest to the plasma were detected in recent experiments. Deposition in the gaps accompanied by metal mixing demand for development of effective cleaning techniques. In experiments with ITER-like castellation, the gaps were cleaned from carbonaceous deposits using oxygen plasmas at 350 degrees C. This contribution contains an overview of experimental and modeling results along with recommendations for PFCs in ITER.
|
|
| 5. |
- Rubel, Marek, et al.
(författare)
-
Overview of wall probes for erosion and deposition studies in the TEXTOR tokamak
- 2017
-
Ingår i: Matter and Radiation at Extremes. - : Elsevier B.V.. - 2468-2047 .- 2468-080X. ; 2:3, s. 87-104
-
Tidskriftsartikel (refereegranskat)abstract
- An overview of diagnostic tools – test limiters and collector probes – used over the years for material migration studies in the TEXTOR tokamak is presented. Probe transfer systems are shown and their technical capabilities are described. This is accompanied by a brief presentation of selected results and conclusions from the research on material erosion – deposition processes including tests of candidate materials (e.g. W, Mo, carbon-based composites) for plasma-facing components in controlled fusion devices. The use of tracer techniques and methods for analysis of materials retrieved from the tokamak are summarized. The impact of research on the reactor wall technology is addressed.
|
|
| 6. |
- Sergienko, G., et al.
(författare)
-
Experience with bulk tungsten test-limiters under high heat loads : melting and melt layer propagation
- 2007
-
Ingår i: Physica Scripta. - 0031-8949 .- 1402-4896. ; T128, s. 81-86
-
Tidskriftsartikel (refereegranskat)abstract
- The paper provides an overview of processes and underlying physics governing tungsten melt erosion in the fusion plasma environment. Experiments with three different bulk tungsten test-limiters were performed in TEXTOR: (i) thermally insulated solid plate fixed on a graphite roof-like limiter heated up by the plasma to the melting point, (ii) macro-brush of the ITER-relevant castellated structure and (iii) lamellae structure developed for the JET divertor. The main objectives were to determine the metal surface damage, the formation of the melt layer and its motion in the magnetic field. PHEMOBRID-3D and MEMOS-1.5D numerical codes were used to simulate the experiment with the roof-like test-limiter. Both experiments and simulation showed that the melting of tungsten can lead to a large material redistribution due to thermo-electron emission currents without ejection of molten material to the plasma.
|
|
| 7. |
- Weckmann, Armin, et al.
(författare)
-
Review on global migration, fuel retention and modelling after TEXTOR decommission
- 2018
-
Ingår i: NUCLEAR MATERIALS AND ENERGY. - : ELSEVIER SCIENCE BV. - 2352-1791. ; 17, s. 83-112
-
Forskningsöversikt (refereegranskat)abstract
- Before decommissioning of the TEXTOR tokamak in 2013, the machine was conditioned with a comprehensive migration experiment where MoF6 and N-15(2) were injected on the very last operation day. Thereafter, all plasmafacing components (PFCs) were available for extensive studies of both local and global migration of impurities - Mo, W, Inconel alloy constituents, 15 N, F - and fuel retention studies. Measurements were performed on 140 limiter tiles out of 864 throughout the whole machine to map global transport. One fifth of the introduced molybdenum could be found. Wherever possible, the findings are compared to results obtained previously in other machines. This review incorporates both published and unpublished results from this TEXTOR study and combines findings with analytical methods as well as modelling results from two codes, ERO and ASCOT. The main findings are: Both local and global molybdenum transport can be explained by toroidal plasma flow and (sic) x (sic) drift. The suggested transport scheme for molybdenum holds also for other analysed species, namely tungsten from previous experiments and medium-Z metals (Cr-Cu) introduced on various occasions. Analytical interpretation of several deposition profile features is possible with basic geometrical and plasma physics considerations. These are deposition profiles on the collector probe, the lower part of the inner bumper limiter, the poloidal cross-section of the inner bumper limiter, and the poloidal limiter. Any deposition pattern found in this TEXTOR study, including fuel retention, has neither poloidal nor toroidal symmetry, which is often assumed when determining deposition profiles on global scale. Fuel retention is highly inhomogeneous due to local variation of plasma parameters - by auxiliary heating systems and impurity injection - and PFC temperature. Local modelling with ERO yields good qualitative agreement but too high local deposition efficiency. Global modelling with ASCOT shows that the radial electric field and source form have a high impact on global deposition patterns, while toroidal flow has little influence. Some of the experimental findings could be reproduced. Still, qualitative differences between simulated and experimental global deposition patterns remain. The review closes with lessons learnt during this extensive TEXTOR study which might be helpful for future scientific exploitation of other tokamaks to be decommissioned.
|
|
| 8. |
- Huber, A., et al.
(författare)
-
Comparison of impurity production, recycling and power deposition on carbon and tungsten limiters in TEXTOR-94
- 2001
-
Ingår i: Journal of Nuclear Materials. - 0022-3115 .- 1873-4820. ; 290, s. 276-280
-
Tidskriftsartikel (refereegranskat)abstract
- Impurity production, hydrogen recycling and power deposition on carbon and tungsten limiters have been investigated in TEXTOR-94 using a C-W twin test limiter. Considerable differences have been observed on W and C surfaces, which can be explained by the different particle and energy reflection coefficients of hydrogen on these surfaces. The measurements show in addition that the majority of the carbon release is from recycled carbon and that only a small part (below 10%) is due to net-erosion from the bulk carbon material. The heat deposition on C and W sides differs under the same plasma conditions significantly and is typically about 30% larger on the cal bon surface. The behaviour of the impurity production: recycling and power deposition for various discharge conditions is presented.
|
|
| 9. |
- Laux, M., et al.
(författare)
-
Arcing at B4C-covered limiters exposed to a SOL-plasma
- 2003
-
Ingår i: Journal of Nuclear Materials. - 0022-3115 .- 1873-4820. ; 313, s. 62-66
-
Tidskriftsartikel (refereegranskat)abstract
- Plasma sprayed B4C-layers considered as wall coatings for the W7X stellarator have been studied during and after exposure to TEXTOR and after arcing experiments in vacuum. Arcing through the B4C layer occurred favoured by high power fluxes and not restricted to less stable phases. But this arcing implies an especially noisy scrape-off layer (SOL). Instead of moving retrograde in the external magnetic field, the arc spot on the B4C-layer sticks to the same location for its whole lifetime. Consequently, the arc erodes the entire B4C layer, finally burning down to the Cu substrate. In the neighbourhood of craters the surface contains Cu originating from those craters. This material, hauled to the surface by the arc, is subject to subsequent erosion, transport, and redeposition by the SOL-plasma. The behaviour of arcs on B4C is Most probably caused by the peculiar temperature dependences of the electrical and heat conductivity of B4C.
|
|
| 10. |
- Litnovsky, A., et al.
(författare)
-
Dust investigations in TEXTOR : Impact of dust on plasma-wall interactions and on plasma performance
- 2013
-
Ingår i: Journal of Nuclear Materials. - : Elsevier BV. - 0022-3115 .- 1873-4820. ; 438:Suppl., s. S126-S132
-
Tidskriftsartikel (refereegranskat)abstract
- Dust will have severe impact on ITER performance since the accumulation of tritium in dust represents a safety issue, a possible reaction of dust with air and steam imposes an explosion hazard and the penetration of dust in core plasmas may degrade plasma performance by increasing radiative losses. Investigations were performed in TEXTOR where known amounts of pre-characterized carbon, diamond and tungsten dust were mobilized into plasmas using special dust holders. Mobilization of dust changed a balance between plasma-surface interactions processes, significantly increasing net deposition. Immediately after launch dust was dominating both core and edge plasma parameters. Remarkably, in about 100 ms after the launch, the effect of dust on edge and core plasma parameters was vanished: no increase of carbon and tungsten concentrations in the core plasmas was detected suggesting a prompt transport of dust to the nearby plasma-facing components without further residence in the plasma.
|
|
