| 1. |
- Bécoulet, A., et al.
(författare)
-
Science and technology research and development in support to ITER and the Broader Approach at CEA
- 2013
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 53:10
-
Tidskriftsartikel (refereegranskat)abstract
- In parallel to the direct contribution to the procurement phase of ITER and Broader Approach, CEA has initiated research & development programmes, accompanied by experiments together with a significant modelling effort, aimed at ensuring robust operation, plasma performance, as well as mitigating the risks of the procurement phase. This overview reports the latest progress in both fusion science and technology including many areas, namely the mitigation of superconducting magnet quenches, disruption-generated runaway electrons, edge-localized modes (ELMs), the development of imaging surveillance, and heating and current drive systems for steady-state operation. The WEST (W Environment for Steady-state Tokamaks) project, turning Tore Supra into an actively cooled W-divertor platform open to the ITER partners and industries, is presented.
|
|
| 2. |
- Corre, Y., et al.
(författare)
-
Testing of ITER-grade plasma facing units in the WEST tokamak: Progress in understanding heat loading and damage mechanisms
- 2023
-
Ingår i: Nuclear Materials and Energy. - : Elsevier BV. - 2352-1791. ; 37
-
Tidskriftsartikel (refereegranskat)abstract
- Assessing the performance of the ITER design for the tungsten (W) divertor Plasma Facing Units (PFUs) in a tokamak environment is a high priority issue to ensure efficient plasma operation. This paper reviews the most recent results derived from experiments and post-mortem analysis of the ITER-grade PFUs exposed in the WEST tokamak and the associated modelling, with a focus on understanding heat loading and damage evolution. Several shaping options, sharp or chamfered leading edge (LE), unshaped or shaped blocks with a toroidal bevel as foreseen in ITER, were investigated, under steady state heat fluxes of up to 120 MW⋅m−2 and 6 MW⋅m−2 on the sharp LE and top surface of the block, respectively. A very high spatial resolution (VHR) infrared (IR) camera (0.1 mm/pixel) was used to derive the temporal and surface distribution of the temperature and heat load on the castellated tungsten blocks for different geometric alignment and plasma conditions. Photonic modelling was required to reproduce the IR measurements in particular in the toroidal and poloidal gaps of the mono-block (MB) stacks where high apparent temperatures are observed. Specular reflection is found to be the dominant emitter in these parts of the blocks. W-cracking was observed on the leading edge of the blocks already within the first phase of plasma operation, during which the divertor was equipped with unshaped PFUs, including some intentionally misaligned blocks. Numerical analysis taking into account softening processes and mechanical stresses, revealed brittle failure due to transients as the dominant failure mechanisms. Ductile failure was observed in one particular block used for the melting experiment, therefore under extremely high steady state heat load conditions. W-melting achieved on actively cooled PFU exhibits specific features: shallow melting and slow melt displacement. Plasma exposure of pre-damaged PFUs at various damage levels (crack network and melted droplets) was carried out under high heat load conditions with several hours of cumulated plasma duration. IR data and preliminary surface analyses show no evidence of significant degradation damage progression under these conditions.
|
|
| 3. |
- Fellinger, Joris, et al.
(författare)
-
Tungsten based divertor development for Wendelstein 7-X
- 2023
-
Ingår i: Nuclear Materials and Energy. - 2352-1791. ; 37
-
Tidskriftsartikel (refereegranskat)abstract
- Wendelstein 7-X, the world’s largest superconducting stellarator in Greifswald (Germany), started plasma experiments with a water-cooled plasma-facing wall in 2022, allowing for long pulse operation. In parallel, a project was launched in 2021 to develop a W based divertor, replacing the current CFC divertor, to demonstrate plasma performance of a stellarator with a reactor relevant plasma facing materials with low tritium retention. The project consists of two tasks: Based on experience from the previous experimental campaigns and improved physics modelling, the geometry of the plasma-facing surface of the divertor and baffles is optimized to prevent overloads and to improve exhaust. In parallel, the manufacturing technology for a W based target module is qualified. This paper gives a status update of project. It focusses on the conceptual design of a W based target module, the manufacturing technology and its qualification, which is conducted in the framework of the EUROfusion funded WPDIV program. A flat tile design in which a target module is made of a single target element is pursued. The technology must allow for moderate curvatures of the plasma-facing surface to follow the magnetic field lines. The target element is designed for steady state heat loads of 10 MW/m2 (as for the CFC divertor). Target modules of a similar size and weight as for the CFC divertor are assumed (approx. < 0.25 m2 and < 60 kg) using the existing water cooling infrastructure providing 5 l/s and roughly maximum 15 bar pressure drop per module. The main technology under qualification is based on a CuCrZr heat sink made either by additive manufacturing using laser powder bed fusion (LPBF) or by uniaxial diffusion welding of pre-machined forged CuCrZr plates. After heat treatment, the plasma-facing side of the heat sink is covered by W or if feasible by the more ductile WNiFe, preferably by coating or alternatively by hot isostatic pressing W based tiles with a soft OFE-Cu interlayer. Last step is a final machining of the plasma-exposed surface and the interfaces to the water supply lines and supports to correct manufacturing deformations.
|
|
| 4. |
- Tichit, Q., et al.
(författare)
-
Infrared detection of tungsten cracking on actively cooled ITER-like component during high power experiment in WEST
- 2023
-
Ingår i: Nuclear Materials and Energy. - : Elsevier BV. - 2352-1791. ; 37
-
Tidskriftsartikel (refereegranskat)abstract
- The consequences of tungsten (W) damaging processes, such as cracking and melting, on divertor lifetime and plasma operation are high priority issues for ITER. A sustained melting experiment was conducted in WEST using a 2 mm deep groove geometry on the upstream mono-block (MB) to overexpose the sharp leading edge (LE) of the downstream MB. W-cracking has been evidenced for the first time with a very high spatial resolution infrared camera before tungsten melting was reached. These cracks develop when the monoblock temperature is about 2600 degrees C, thus higher than both ductile to brittle transition and softening threshold of tungsten, suggesting that these cracks are different from the ones observed in previous campaigns where brittle failure was involved, because of transient events on cold monoblock. Post-exposure analyses have been performed on the damaged monoblock, highlighting 12 main cracks on the LE, with a width varying from 33 mu m to 77 mu m, and an average spacing of 0.45 mm. Parallel heat flux about 90 MW/m2 has been derived from infrared temperature measurements, with a heat flux decay length on the target of 4 mm. The T-REX modelling code suggest here that with these thermal inputs, a crack can initiates due to thermal cycling without disruption, with a ductile failure, under 1 to 5 cycles for a tungsten DBTT varying from 400 degrees C to 500 degrees C.
|
|
