| 1. |
- Stolen, Reidar, et al.
(författare)
-
Solcelleteknologi og brannsikkerhet
- 2018
-
Rapport (övrigt vetenskapligt/konstnärligt)abstract
- Bruken av solcelleteknologi er i stor vekst i Norge. I denne studien er branntekniske utfordringer ved bruk av solcelleteknologi undersøkt, med hensyn på brannstart, brannspredning og brannslokking. Studien danner et kunnskapsgrunnlag for å ivareta brannsikkerheten under montering, drift og under slokkeinnsats, samt for å utforme et enhetlig og tydelig regelverk. Resultatene fra studien viser:Brannstart: Solcelleinstallasjoner inneholder mange koblingspunkt, som kan være potensielle tennkilder, og en liten mengde brennbare materialer. Dermed er det som trengs til stede for å starte en brann. Det er viktig at alle kontaktpunkter i solcelleinstallasjonen er robuste og tåler den påkjenningen de blir utsatt for gjennom sin levetid uten at det oppstår dårlig kontakt som kan føre til brann.Brannspredning: For utenpåmonterte solcellemoduler er det ofte en åpen luftspalte mellom modul og bygning. Dersom det er en brann i denne luftspalten, vil varmen kunne bli akkumulert, noe som kan føre til raskere og større brannspredning enn om bygningsoverflaten ikke hadde vært tildekket. I fullskalaforsøk med solcellemoduler montert på tak spredte brannen seg under hele arealet som var dekket av moduler, men stoppet da den nærmet seg kanten av dette arealet. Dette illustrerer viktigheten av at områder med solceller utenpå en bygning blir seksjonert for å unngå brannspredning. Eventuelt kan det benyttes mindre brennbare materialer på taket under solcellemodulene for å motvirke den økte varmepåkjenningen som solcellemodulene gir. Luftspalten mellom modul og bygning kan potensielt også gi endringer i luftstrømningen langs bygget, som igjen kan påvirke brannspredningen.Brannslokking: Brannvesenet har behov for informasjon om det er solcelleinstallasjon i bygget og hvilke deler av det elektriske anlegget som kan være spenningssatt. Under slokkeinnsats må brannvesenet ta hensyn til berøringsfare, og fare for at det kan oppstå lysbuer og andre feil som kan føre til nye antennelsespunkt. Ferskvann kan brukes som slokkemiddel, dette må spyles fra minimum 1 meters avstand med spredt stråle og minimum 5 meters avstand med samlet stråle. Solcellemoduler kan komplisere brannslokking ved at de danner en fysisk barriere mellom brannvesenet og brannen, samt fordi det må tas hensyn til plassering av spenningssatte komponenter. Når disse punktene er tatt høyde for, bør ikke utenpåmonterte solcelleinstallasjoner være et problem.Videre arbeid: For utenpåmonterte solcelleinstallasjoner, er det lite forskning på vertikal montering (på fasader), og hvordan en eventuell endret branndynamikk kan påvirke brannspredning og slokking. Videre er det i dag økende bruk av bygningsintegrerte solcelleinstallasjoner, noe som gir mange mulige nye utfordringer for brannsikkerheten og for regelverk, ettersom solcellen da er en del av bygningskroppen, samtidig som den er en elektrisk komponent. Tysk statistikk tyder på at brannrisiko for slike installasjoner kan være større enn for utenpåmonterte solcelleinstallasjoner, og dette vil det derfor være viktig å undersøke nærmere.
|
|
| 2. |
- Eivazihollagh, Alireza, et al.
(författare)
-
On chelating surfactants : Molecular perspectives and application prospects
- 2019
-
Ingår i: Journal of Molecular Liquids. - : Elsevier BV. - 0167-7322 .- 1873-3166. ; 278, s. 688-705
-
Tidskriftsartikel (refereegranskat)abstract
- Chelating agents, molecules that very strongly coordinates certain metal ions, are used industrially as well as in consumer products to minimize disturbances and increase performance of reactions and applications. The widely used sequestering agents, nitrilotriacetic acid (NTA), ethylenediaminetetraacetic acid (EDTA) and diethylenetriaminepentaacetic acid (DTPA) belong to this branch of readily water-soluble compounds. When these chemical structures also have hydrophobic parts, they are prone to adsorb at air-water interfaces and to self-assemble. Such bifunctional molecules can be called chelating surfactants and will have more extended utilization prospects than common chelating agents or ordinary ionic surfactants. The present review attempts to highlight the fundamental behavior of chelating surfactants in solution and at interfaces, and their very specific interactions with metal ions. Methods to recover chelating surfactants from metal chelates are also described. Moreover, utilization of chelating surfactants in applications for metal removal in environmental engineering and mineral processing, as well as for metal control in the fields of biology, chemistry and physics, is exemplified and discussed.
|
|
| 3. |
- Petersson, Jesper, 1974
(författare)
-
Blurring the shoreline: De- and re-infrastructuring and the changing colors of European flood policy
- 2021
-
Ingår i: Environment and Planning E: Nature and Space. - : SAGE Publications. - 2514-8494 .- 2514-8494 .- 2514-8486. ; 4:2, s. 623-644
-
Tidskriftsartikel (refereegranskat)abstract
- This paper provides a genealogy of the emergence of a common EU flood policy, including the scope and direction of this policy. Noticing how EU policy proposes green infrastructure (associated with using nature as a buffer zone in managing floods) as an alternative to grey infrastructure (implying fixed installations of concrete and cement), this paper adopts the theoretical lens of the so-called infrastructural turn, which advocates a relational investigation of infrastructure. By engaging this approach, the paper shows how flood infrastructure can contain very different compositions of (unruly) water and (settled) land. A narrative of a historically strong focus on guarding society from the powerful forces of nature through a fixed line of defense is increasingly giving way to more muddy states—quite literally—where society is expected to learn to live with flooding and show ecological consideration. To capture the EU’s, and especially the European Commission’s efforts to establish a pan-European flood infrastructure that accommodates this turn, the concepts of de- and re-infrastructuring are developed. These concepts act as heuristic devices to capture how policy performs some combinations between water and land as constituting an attractive and functional flood infrastructure, but constitutes other infrastructural relations of the aquatic and the terrestrial as undesirable and, hence, as malfunctioning. This performative act of distinguishing between what constitutes “good and proper” versus “bad and undesirable” infrastructure is referred to as a politics of infrastructure.
|
|
| 4. |
- Thomas, Jean-Baptiste, et al.
(författare)
-
A comparative environmental life cycle assessment of hatchery, cultivation, and preservation of the kelp Saccharina latissima
- 2021
-
Ingår i: Ices Journal of Marine Science. - : Oxford University Press (OUP). - 1054-3139 .- 1095-9289. ; 78:1, s. 451-467
-
Tidskriftsartikel (refereegranskat)abstract
- Seaweed cultivation and processing industries could contribute to sustainable blue growth and the European bioeconomy. This article contributes a case study evaluation of environmental sustainability of preserved brown seaweed Saccharina latissima by means of environmental life cycle assessment of a pilot facility in Sweden. The study accounts for nutrient bioremediation and carbon capture and includes two alternative hatchery processes, a 2-ha longline cultivation, and four alternative preservation methods (hang-drying outdoors, heated air-cabinet drying, ensiling, and freezing). The study found that as a result of carbon capture and nitrogen and phosphorus uptake (bioremediation) by seaweed, more CO2 and PO4 equivalents are (temporarily) absorbed than emitted by the supply chain. The extent of emissions is most affected by preservation methods undertaken. Impact profiles of the supply chain show that the greatest impact shares result from freezing and air-cabinet drying, both the two most energy-intensive processes, followed by the cultivation infrastructure, highlighting strategic optimization opportunities. Hatchery processes, harvesting, and the low-energy ensilage and hang-drying outdoors were found to have relatively small impact shares. These findings presage the environmentally friendliness of seaweed-based products by documenting their potential to mitigate eutrophication and climate change, even when taking a life cycle perspective.
|
|
| 5. |
- Englund, Oskar, 1982, et al.
(författare)
-
Large-scale deployment of grass in crop rotations as a multifunctional climate mitigation strategy
- 2023
-
Ingår i: GCB Bioenergy. - : Wiley. - 1757-1707 .- 1757-1693. ; 15:2, s. 166-184
-
Tidskriftsartikel (refereegranskat)abstract
- The agriculture sector can contribute to climate change mitigation by reducing its own greenhouse gas (GHG) emissions, sequestering carbon in vegetation and soils, and providing biomass to substitute for fossil fuels and other GHG-intensive products. The sector also needs to address water, soil, and biodiversity impacts caused by historic and current practices. Emerging EU policies create incentives for cultivation of perennial plants that provide biomass along with environmental benefits. One such option, common in northern Europe, is to include grass in rotations with annual crops to provide biomass while remediating soil organic carbon (SOC) losses and other environmental impacts. Here, we apply a spatially explicit model on >81,000 sub-watersheds in EU27 + UK (Europe) to explore the effects of widespread deployment of such systems. Based on current accumulated SOC losses in individual sub-watersheds, the model identifies and quantifies suitable areas for increased grass cultivation and corresponding biomass- and protein supply, SOC sequestration, and reductions in nitrogen emissions to water as well as wind and water erosion. The model also provides information about possible flood mitigation. The results indicate a substantial climate mitigation potential, with combined annual GHG savings from soil-carbon sequestration and displacement of natural gas with biogas from grass-based biorefineries, equivalent to 13%–48% of current GHG emissions from agriculture in Europe. The environmental co-benefits are also notable, in some cases exceeding the estimated mitigation needs. Yield increases for annual crops in modified rotations mitigate the displacement effect of increasing grass cultivation. If the grass is used as feedstock in lieu of annual crops, the displacement effect can even be negative, that is, a reduced need for annual crop production elsewhere. Incentivizing widespread deployment will require supportive policy measures as well as new uses of grass biomass, for example, as feedstock for green biorefineries producing protein concentrate, biofuels, and other bio-based products.
|
|
| 6. |
- André, Hampus, 1989
(författare)
-
Resource and Environmental Impacts of Resource-Efficiency Measures Applied to Electronic Products
- 2018
-
Licentiatavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Natural resources such as ecosystems, land, water and metals underpin the functioning of economies and human well-being, and are becoming increasingly scarce due to growth in population and affluence. Metals are increasingly demanded for their specific properties as modern technology develops. The dependence on metals is of growing concern due to the environmental impacts related, for example, to energy use and local impacts from mining, as well as the scarcity risks posed by socio-economic, geological and geopolitical constraints. Thus, there is a clear need to use metals and other natural resources more efficiently. The vision of a circular economy has been proposed as a way to do this, for example by improving durability, reusing, repairing and recycling. Such so-called resource-efficiency (RE) measures are commonly assumed to be environmentally beneficial, although the evidence is not plentiful. It is plausible that focusing on recirculating products and materials could shift burdens to other environmental impacts or life cycle stages. It has therefore been argued that a life cycle-based approach, such as in life cycle assessment (LCA), is useful to critically assess the environmental implications of RE measures. LCA aims to quantify the environmental impacts of products over their entire life cycles - from cradle to grave - assessing a wide range of impacts such as toxicity, climate change and metal resource use. For metal resource use, however, there are a number of perspectives as to what constitutes the actual environmental problem. These perspectives are represented in a variety of life cycle impact assessment methods (LCIA) which have previously been shown to give diverging results. Electronic products are emblematic of metal resource use challenges since they deploy a broad spectrum of scarce metals. This thesis aims to provide knowledge on the potential for RE measures to reduce the environmental impacts of electronic products, by addressing the following research questions: (1) What resource-efficiency measures result in reduced potential environmental impacts and resource use – for what types of products and under what conditions? (2) How does extended use of electronic products through design for increased technical lifetime, reuse and repair affect environmental impacts, particularly metal resource use? (3) How does the application of different LCIA methods for metal resource use influence interpretations of resource-efficiency measures applied to electronic products? This thesis builds on three appended papers which are all based on comparative assessments of resource efficiency, studied as resource use and environmental impacts per function delivered, using LCA and material flow analysis. The results indicate that extended use of electronic products through increasing technical lifetimes, reusing and repairing, is generally resource-efficient. Exceptions may occur, however, if extended use is insufficient to motivate impacts from producing more durable products or spare parts. Use extension of electronic products leads to resource efficiency in two distinct ways: through the intended use extension and by increasingly steering material flows into recycling. Further resource efficiency could be realised by combining RE measures over the entire life cycles of products. With regards to metal resource use, the choice of LCIA method can influence the interpretation of the results of RE measures for electronic products. Therefore, it is advisable to use several complementary LCIA methods to minimise the risks of overlooking potentially important resources issues. Furthermore, better understanding and transparency of such issues is valuable in order to provide more comprehensive information to decision-makers.
|
|
| 7. |
- Ahrné, Karin, et al.
(författare)
-
Tillstånd och trender för arter och deras livsmiljöer – rödlistade arter i Sverige 2015
- 2015
-
Rapport (övrigt vetenskapligt/konstnärligt)abstract
- 2015 års upplaga av den svenska rödlistan är den fjärde i ordningen. Den är baserad på IUCN:s rödlistningskriterier och revideras vart femte år. I rödlistan bedöms risken som enskilda arter av djur, växter och svampar löper att försvinna från Sverige. Bedömningen utförs av ArtDatabankens medarbetare i samverkan med över 100 externa experter, indelade i 14 expertkommittéer för olika organismgrupper. Under arbetet med 2015 års rödlista har tillstånd och trender bedömts för 21 600 arter och 1 318 lägre taxa (apomiktiska arter, underarter och varieteter), sammanlagt ca 22 900 taxa. Av de bedömda arterna klassificerades 2 029 som hotade (kategorierna CR, EN och VU) och 4 273 som rödlistade (inkluderar även kategorierna NT, RE och DD). Förhållandet mellan antalet rödlistade och antalet bedömda arter ar 19,8 %, vilket är ungefär samma värde som 2010 och 2005. I denna rapport jämförs antalet och andelen rödlistade arter mellan olika organismgrupper, biotoper, substrat och påverkansfaktorer. Texten ar indelad i en allmän del och åtta kapitel inriktade på olika landskapstyper. Landskapstyperna utgör en grov indelning av landets miljöer enligt följande kategorier: Skog, Jordbrukslandskap, Urbana miljöer, Fjäll, Våtmarker, Sötvatten, Havsstränder och Havsmiljöer. Skogen och jordbrukslandskapet är de artrikaste landskapstyperna med 1 800 respektive 1 400 arter som har en stark anknytning dit, och ytterligare flera hundra arter som förekommer där mer sporadiskt. De faktorer som påverkar flest rödlistade arter i Sverige är skogsavverkning och igenväxning, som båda utgör ett hot mot vardera ca 30 % av de rödlistade arterna. Avverkning minskar arealen av skog där naturliga strukturer och naturlig dynamik upprätthålls, och den orsakar därmed förlust av livsmiljöer. Igenväxning orsakas av ett antal faktorer, bland annat upphörande hävd (bete och slåtter), gödsling, trädplantering och brist på naturliga störningsregimer som t.ex. regelbundna översvämningar kring vattendrag och sjöar. Andra viktiga påverkansfaktorer är fiske, torrläggning av våtmarker, tillbakagång hos värdarter (främst alm och ask som drabbats av invasiva svampsjukdomar), klimatförändringar och konkurrens från invasiva arter. IUCN:s rödlisteindex beräknas för ett urval av de bedömda organismgrupperna. Rödlisteindex visar att skillnaderna mellan rödlistorna från 2000, 2005, 2010 och 2015 är små. Ett par undantag finns dock. Groddjur och stora däggdjur har fått en något förbättrad situation sedan 2000. Totalt förefaller det ändå som att trycket mot Sveriges artstock har förblivit relativt konstant under de senaste 15 åren.
|
|
| 8. |
- Shahroozi, Zahra, 1992-
(författare)
-
Survivability control using data-driven approaches and reliability analysis for wave energy converters
- 2024
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Wave energy, with five times the energy density of wind and ten times the power density of solar, offers a compelling carbon-free electricity solution. Despite its advantages, ongoing debates surround the reliability and economic feasibility of wave energy converters (WECs). To address these challenges, this doctoral thesis is divided into four integral parts, focusing on optimizing the prediction horizon for power maximization, analyzing extreme waves' impact on system dynamics, ensuring reliability, and enhancing survivability in WECs.Part I emphasizes the critical importance of the prediction horizon for maximal power absorption in wave energy conversion. Using generic body shapes and modes, it explores the effect of dissipative losses, noise, filtering, amplitude constraints, and real-world wave parameters on the prediction horizon. Findings suggest achieving optimal power output may be possible with a relatively short prediction horizon, challenging traditional assumptions.Part II shifts focus to WEC system dynamics, analyzing extreme load scenarios. Based on a 1:30 scaled wave tank experiment, it establishes a robust experimental foundation, extending into numerical assessment of the WEC. Results underscore the importance of damping to alleviate peak forces. Investigating various wave representations highlights conservative characteristics of irregular waves, crucial for WEC design in extreme sea conditions.Part III explores the computational intricacies of environmental design load cases and fatigue analyses for critical mechanical components of the WEC. The analysis is conducted for hourly sea state damage and equivalent two-million-cycle loads. Finally, a comparison of safety factors between the ultimate limit state and fatigue limit state unfolds, illustrating the predominant influence of the ultimate limit state on point-absorber WEC design.Part IV, centers on elevating survivability strategies for WECs in extreme wave conditions. Three distinct controller system approaches leverage neural networks to predict and minimize the line force. Distinct variations emerge in each approach, spanning from rapid detection of optimal damping to integrating advanced neural network architectures into the control system with feedback. The incorporation of a controller system, refined through experimental data, showcases decreases in the line force, providing a practical mechanism for real-time force alleviation.This thesis aims to contribute uniquely to the goal of advancing wave energy conversion technology through extensive exploration.
|
|
| 9. |
- Johansson, Björn, 1975, et al.
(författare)
-
Power Level Sampling of Metal Cutting Machines for Data Representation in Discrete Event Simulation
- 2015
-
Ingår i: International Journal of Production Research. - : Informa UK Limited. - 0020-7543 .- 1366-588X. ; 53:23, s. 7060-7070
-
Tidskriftsartikel (refereegranskat)abstract
- An extension to the application area for discrete event simulation (DES) has been ongoing since the last decade and focused only on economic aspects to include ecologic sustainability. With this new focus, additional input parameters, such as electrical power consumption of machines, are needed. This paper aim at investigating how NC machine power consumption should be represented in simulation models of factories. The study includes data-sets from three different factories. One factory producing truck engine blocks, one producing brake disc parts for cars and one producing forklift components. The total number of data points analysed are more than 2,45,000, where of over 1,11,000 on busy state for 11 NC machines. The low variability between busy cycles indicates that statistical representations are not adding significant variability. Furthermore, results show that non-value-added activities cause a substantial amount of the total energy consumption, which can be reduced by optimising the production flow using dynamic simulations such as DES.
|
|
| 10. |
- Bjorn, A., et al.
(författare)
-
Review of life-cycle based methods for absolute environmental sustainability assessment and their applications
- 2020
-
Ingår i: Environmental Research Letters. - : IOP Publishing Ltd. - 1748-9326 .- 1748-9318. ; 15:8
-
Tidskriftsartikel (refereegranskat)abstract
- In many regions and at the planetary scale, human pressures on the environment exceed levels that natural systems can sustain. These pressures are caused by networks of human activities, which often extend across countries and continents due to global trade. This has led to an increasing requirement for methods that enable absolute environmental sustainability assessment (AESA) of anthropogenic systems and which have a basis in life cycle assessment (LCA). Such methods enable the comparison of environmental impacts of products, companies, nations, etc, with an assigned share of environmental carrying capacity for various impact categories. This study is the first systematic review of LCA-based AESA methods and their applications. After developing a framework for LCA-based AESA methods, we identified 45 relevant studies through an initial survey, database searches and citation analysis. We characterized these studies according to their intended application, impact categories, basis of carrying capacity estimates, spatial differentiation of environmental model and principles for assigning carrying capacity. We then characterized all method applications and synthesized their results. Based on this assessment, we present recommendations to practitioners on the selection and use of existing LCA-based AESA methods, as well as ways to perform assessments and communicate results to decision-makers. Furthermore, we identify future research priorities intended to extend coverage of all components of the proposed method framework, improve modeling and increase the applicability of methods. © 2020 The Author(s).
|
|
