| 2. |
- Okabayashi, M., et al.
(författare)
-
Control of the resistive wall mode with internal coils in the DIII-D tokamak
- 2005
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 45:12, s. 1715-1731
-
Tidskriftsartikel (refereegranskat)abstract
- Internal coils, 'I-Coils', were installed inside the vacuum vessel of the DIII-D device to generate non-axisymmetric magnetic fields to act directly on the plasma. These fields are predicted to stabilize the resistive wall mode (RWM) branch of the long-wavelength external kink mode with plasma beta close to the ideal wall limit. Feedback using these I-Coils was found to be more effective as compared to using external coils located outside the vacuum vessel. Locating the coils inside the vessel allows for a faster response and the coil geometry also allows for better coupling to the helical mode structure. Initial results were reported previously (Strait E.J. et al 2004 Phys. Plasmas 11 2505). This paper reports on results from extended feedback stabilization operations, achieving plasma parameters up to the regime of Cβ ≈ 1.0 and open loop growth rates of γopenτw ≳ 25 where the RWM was predicted to be unstable with only the 'rotational viscous stabilization mechanism'. Here Cβ ≈ (β - βno-wall.limit)/(βideal.wall.limit - βno-wall.limit) is a measure of the beta relative to the stability limits without a wall and with a perfectly conducting wall, and τw is the resistive flux penetration time of the wall. These feedback experimental results clarified the processes of dynamic error field correction and direct RWM stabilization, both of which took place simultaneously during RWM feedback stabilization operation. MARS-F modelling provides a critical rotation velocity in reasonable agreement with the experiment and predicts that the growth rate increases rapidly as rotation decreases below the critical. The MARS-F code also predicted that for successful RWM magnetic feedback, the characteristic time of the power supply should be limited to a fraction of the growth time of the targeted RWM. The possibility of further improvements in the presently achievable range of operation of feedback gain values is also discussed.
|
|
| 3. |
- Liu, Yueqiang, 1971, et al.
(författare)
-
Modeling of resistive wall mode and its control in experiments and ITER
- 2006
-
Ingår i: Physics of Plasmas. - : AIP Publishing. - 1089-7674 .- 1070-664X. ; 13:5
-
Tidskriftsartikel (refereegranskat)abstract
- Active control of the resistive wall mode (RWM) for DIII-D [Luxon and Davis, Fusion Technol. 8, 441 (1985)] plasmas is studied using the MARS-F code [Y. Q. Liu, Phys. Plasmas 7, 3681 (2000)]. Control optimization shows that the mode can be stabilized up to the ideal wall beta limit, using the internal control coils (I-coils) and poloidal sensors located at the outboard midplane, in combination with an ideal amplifier. With the present DIII-D power supply model, the stabilization is achieved up to 70% of the range between no-wall and ideal-wall limits. Reasonably good quantitative agreement is achieved between MARS-F simulations and experiments on DIII-D and JET (Joint European Torus) [P. H. Rebut, Nucl. Fusion 25, 1011 (1985)] on critical rotation for the mode stabilization. Dynamics of rotationally stabilized plasmas is well described by a single mode approximation; whilst a strongly unstable plasma requires a multiple mode description. For ITER [R. Aymar, P. Barabaschi, and Y. Shimomura, Plasma Phys. Controlled Fusion 44, 519 (2002)], the MARS-F simulations show the plasma rotation may not provide a robust mechanism for the RWM stabilization in the advanced scenario. With the assumption of ideal amplifiers, and using optimally tuned controllers and sensor signals, the present feedback coil design in ITER allows stabilization of the n=1 RWM for plasma pressures up to 80% of the range between the no-wall and ideal-wall limits.
|
|
