| 1. |
- Stork, D., et al.
(författare)
-
Overview of transport, fast particle and heating and current drive physics using tritium in JET plasmas
- 2005
-
Ingår i: Nuclear Fusion. - 0029-5515 .- 1741-4326. ; 45:10, s. S181-S194
-
Tidskriftsartikel (refereegranskat)abstract
- Results are presented from the JET Trace Tritium Experimental (TTE) campaign using minority tritium (T) plasmas (n(T)/n(D) < 3%). Thermal tritium particle transport coefficients (D-T, nu(T)) are found to exceed neo-classical values in all regimes, except in ELMy H-modes at high densities and in the region of internal transport barriers (ITBs) in reversed shear plasmas. In ELMy H-mode dimensionless parameter scans, at q(95) 2.8 and triangularity delta = 0.2, the T particle transport scales in a gyro-Bohm manner in the inner plasma (r/a < 0.4), whilst the outer plasma particle transport scaling is more Bohm-like. Dimensionless parameter scans show contrasting behaviour for the trace particle confinement (increases with collisionality, nu* and beta) and bulk energy confinement (decreases with nu* and is independent of beta). In an extended ELMy H-mode data set, with rho*, nu*, and q varied but with neo-classical tearing modes (NTMs) either absent or limited to weak, benign core modes (4/3 or above), the multiparameter fit to the normalized diffusion coefficient in the outer plasma (0.65 < r/a < 0.8) gives D-T/B-phi similar to rho*(2.46) nu*(-0.23) beta(-1.01) q(2.03). In hybrid scenarios (q(min) similar to 1, low positive shear, no sawteeth), the T particle confinement is found to scale with increasing triangularity and plasma current. Comparing regimes (ELMy H-mode, ITB plasma and hybrid scenarios) in the outer plasma region, a correlation of high values of D-T with high values Of nu(T) is seen. The normalized diffusion coefficients for the hybrid and ITB scenarios do not fit the scaling derived for ELMy H-modes. The normalized tritium diffusion scales with normalized poloidal Larmor radius (rho(theta)* = q rho*) in a manner close to gyro-Bohm (similar to rho(sigma)*(3)), with an added inverse P dependence. The effects of ELMs, sawteeth and NTMs on the T particle transport are described. Fast-ion confinement in current-hole (CH) plasmas was tested in TTE by tritium neutral beam injection into JET CH plasmas. gamma-rays from the reactions of fusion alpha and beryllium impurities (Be-9(alpha, n gamma)C-12) characterized the fast fusion-alpha population evolution. The gamma-decay times are consistent with classical alpha plus parent fast triton slowing down times (tau(Ts) + tau(alpha s)) for high plasma currents (I-p > 2 MA) and monotonic q-profiles. In CH discharges the gamma-ray emission decay times are much lower than classical (tau(Ts) + tau(alpha s)), indicating alpha confinement degradation, due to the orbit losses and particle orbit drift predicted by a 3-D Fokker-Planck numerical code and modelled using TRANSP.
|
|
| 2. |
- Hirai, T., et al.
(författare)
-
R&D on full tungsten divertor and beryllium wall for JET ITER-like wall project
- 2007
-
Ingår i: Fusion engineering and design. - : Elsevier BV. - 0920-3796 .- 1873-7196. ; 82:15-24, s. 1839-1845
-
Tidskriftsartikel (refereegranskat)abstract
- The ITER reference materials have been tested separately in tokamaks, plasma simulators, ion beams and high heat flux test beds. In order to perform a fully integrated material test JET has launched the ITER-like Wall Project with the aim of installing a full metal wall during the next major shutdown. As a result of R&D projects in 2005-2006, bulk tungsten tiles are foreseen at the outer horizontal target and tungsten coating at the other divertor tiles. In some regions of the main chamber, beryllium coated Inconel tiles and bulk beryllium tiles are utilised which include marker tiles as erosion diagnostics. This paper gives an overview of the R&D carried out in the frame of the ITER-like Wall Project on the development of an inertially cooled bulk tungsten tile design and the characterization of tungsten and beryllium coating technologies.
|
|
| 3. |
- Maier, H., et al.
(författare)
-
Tungsten and beryllium armour development for the JET ITER-like wall project
- 2007
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 0029-5515 .- 1741-4326. ; 47:3, s. 222-227
-
Tidskriftsartikel (refereegranskat)abstract
- For the ITER-like wall project at JET the present main chamber CFC tiles will be exchanged with Be tiles and in parallel a fully tungsten-clad divertor will be prepared. Therefore three R&D programmes were initiated: Be coatings on Inconel as well as Be erosion markers were developed for the first wall of the main chamber. High heat flux screening and cyclic loading tests carried out on the Be coatings on Inconel showed excellent performance, above the required power and energy density. For the divertor a conceptual design for a bulk W horizontal target plate was investigated, with the emphasis on minimizing electromagnetic forces. The design consisted of stacks of W lamellae of 6 mm width that were insulated in the toroidal direction. High heat flux tests of a test module were performed with an electron beam at an absorbed power density Up to 9 MW m(-2) for more than 150 pulses and finally with increasing power loads leading to surface temperatures in excess of 3000 degrees C. No macroscopic failure occurred during the test while SEM showed the development of micro-cracks on the loaded surface. For all other divertor parts R&D was performed to provide the technology to coat the 2-directional CFC material used at JET with thin tungsten coatings. The W-coated CFC tiles were subjected to heat loads with power densities ranging up to 23.5 MW m(-2) and exposed to cyclic heat loading for 200 pulses at 10.5 MW m(-2). All coatings developed cracks perpendicular to the CFC fibres due to the stronger contraction of the coating upon cool-down after the heat pulses.
|
|
| 4. |
- Matthews, G. F., et al.
(författare)
-
Overview of the ITER-like wall project
- 2007
-
Ingår i: Physica Scripta. - 0031-8949 .- 1402-4896. ; T128, s. 137-143
-
Tidskriftsartikel (refereegranskat)abstract
- Work is in progress to completely replace, in 2008/9, the existing JET CFC tiles with a configuration of plasma facing materials consistent with the ITER design. The ITER-like wall (ILW) will be created with a combination of beryllium ( Be), tungsten ( W), W-coated CFC and Be-coated inconel tiles, with the material depending on the local anticipated heat flux and geometry. It is part of an integrated package of JET enhancements whose aim is to develop an understanding of the ITER materials issues and develop the techniques required to operate with inductive and advanced scenarios as close as possible to ITER parameters. Over 4000 tiles will be replaced and the ILW will accommodate additional heating up to at least 50 MW for 10 s. This paper describes the scientific background to the project, the technical objectives, the material configuration selected, the R&D behind the practical realization of the objectives and the generic problems associated with the Be tiles ( power handling capacity and disruption induced eddy currents). One of the objectives is to maintain or improve the existing CFC tile power handling performance which has been achieved in most cases by hiding bolt holes, optimizing tile size and profile and introducing castellations on plasma facing surfaces.
|
|
