| 1. |
- Salvador, Christian Mark, 1989, et al.
(författare)
-
Indoor ozone/human chemistry and ventilation strategies
- 2019
-
Ingår i: Indoor Air. - : Hindawi Limited. - 1600-0668 .- 0905-6947. ; 29:6, s. 913-925
-
Tidskriftsartikel (refereegranskat)abstract
- This study aimed to better understand and quantify the influence of ventilation strategies on occupant-related indoor air chemistry. The oxidation of human skin oil constituents was studied in a continuously ventilated climate chamber at two air exchange rates (1 h-1 and 3 h-1 ) and two initial ozone mixing ratios (30 and 60 ppb). Additional measurements were performed to investigate the effect of intermittent ventilation ("off" followed by "on"). Soiled t-shirts were used to simulate the presence of occupants. A time-of-flight-chemical ionization mass spectrometer (ToF-CIMS) in positive mode using protonated water clusters was used to measure the oxygenated reaction products geranyl acetone, 6-methyl-5-hepten-2-one (6-MHO) and 4-oxopentanal (4-OPA). The measurement data were used in a series of mass balance models accounting for formation and removal processes. Reactions of ozone with squalene occurring on the surface of the t-shirts are mass transport limited; ventilation rate has only a small effect on this surface chemistry. Ozone-squalene reactions on the t-shirts produced gas-phase geranyl acetone, which was subsequently removed almost equally by ventilation and further reaction with ozone. About 70% of gas-phase 6-MHO was produced in surface reactions on the t-shirts, the remainder in secondary gas-phase reactions of ozone with geranyl acetone. 6-MHO was primarily removed by ventilation, while further reaction with ozone was responsible for about a third of its removal. 4-OPA was formed primarily on the surfaces of the shirts (~60%); gas-phase reactions of ozone with geranyl acetone and 6-MHO accounted for ~30% and ~10%, respectively. 4-OPA was removed entirely by ventilation. The results from the intermittent ventilation scenarios showed delayed formation of the reaction products and lower product concentrations compared to continuous ventilation.
|
|
| 2. |
- Sauer, Christopher, 1993
(författare)
-
Green Aromatics: Catalytic Valorisation of bio-derived 2,5-dimethylfuran over Zeolites and Zeotypes
- 2022
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- This thesis discusses the use of biomass as a potentially green feedstock for the chemical industry in the urgent shift away from fossil resources. I elaborate on reasons why we cannot afford to burn virgin biomass for energy production, among them a variety of ecosystem services that forests and other lands provide. In addition, the utilisation of biomass should be focused on products that sequester and lock away carbon for more extended periods, e.g. timber, materials and chemicals. In particular, biomass can be used as an alternative "carbon neutral" feedstock for the chemical industry, where we can preserve the already existing chemical complexity in the bio-based molecules. One example is the upgrading of furans to benzene, toluene and xylene (BTX) aromatics with the help of zeolite catalysis. These aromatics are important commodity chemicals, where the shift to a bio-based resource could make use of already existing knowledge, catalyst and production infrastructure. However, research is necessary to understand these new feedstock molecules and their interaction with the catalysts and to enable the design of applicable catalysts. In order to study the interaction of the furans, in particular 2,5-dimethylfuran (2,5-dmf), I describe and discuss the development of an analytical methodology that utilises infrared spectroscopy and mass spectrometry for the on-line identification and quantification of product molecules during catalytic reactions. This on-line analysis method is then applied to the catalytic conversion of 2,5-dmf to aromatics over a range of zeolite and zeotype catalysts. In-depth studies with ammonia as a probe molecule of the catalytic active acid sites, as well as temperature programmed experiments with ammonia and 2,5-dmf give insights into product distribution, selectivity changes and deactivation of the catalyst. For example, olefins and aromatics are initially preferred products, while with increasing time on stream, the isomerisation of 2,5-dmf becomes dominant. The incorporation of Ga into the zeotype framework, resulting in a Ga-Silicate, shows how targeted catalyst design can increase overall aromatics production. This catalyst is also suitable for selective isomerisation of 2,5-dmf to 2,4-dimethylfuran, which has a rare substitution pattern. Finally, itwas found that the most valuable of BTX, p -xylene, can be produced more selectively when 2,5-dmf is pre-adsorbed onto zeolite ZSM-5 and then released during a temperature programmed product desorption.
|
|
| 3. |
- Le Breton, Michael, 1986, et al.
(författare)
-
Application of a FIGAERO ToF CIMS for on-line characterization of real-world fresh and aged particle emissions from buses
- 2019
-
Ingår i: Aerosol Science and Technology. - : Informa UK Limited. - 0278-6826 .- 1521-7388. ; 53:3, s. 244-259
-
Tidskriftsartikel (refereegranskat)abstract
- © 2019, © 2019 The Author(s). Published with license by Taylor & Francis Group, LLC. On-line chemical characterization of real-world particle emissions from 13 transit buses was performed using a chemical ionization mass spectrometer (CIMS) equipped with a filter inlet for gases and aerosols (FIGAERO). In addition to the fresh emissions the emissions were artificially aged using a potential aerosol mass reactor (Go:PAM). The buses studied were running on different fuel types (diesel, compressed natural gas, and rapeseed methyl ester) and exhaust after-treatment systems (selective catalytic reduction (SCR), exhaust gas recirculation (EGR), and a three-way catalyst). When evaluating emissions from passing exhaust plumes using the FIGAERO ToF-CIMS, two technical features were highlighted from this work, the use of high mass calibrants and the factor enhancement method to be able to filter important compounds from mass spectra including hundreds of species. Here, acetate was used as the reagent ion to enable detection of highly oxygenated species in the exhaust particle emissions with potential high toxicity and/or secondary organic aerosol formation (SOA) potential. The acetate ionization scheme accounted for 4% to 46% of the total emitted particulate mass through identification of 61 species in the spectra. For aged emission the various fuel types provided overlapping species that could explain up to 19% of the aged emissions. This is hypothesized to come from the oxidation of engine lubrication oil, thus a common source for various fuels which was further supported by laboratory measurements. Specific markers from the SCR technology, such as urea oxidation products and further byproducts from hydrolysis were identified and attributed to reactions of isocyanic acid.
|
|
| 4. |
|
|
| 5. |
- Shwan, Soran, 1984
(författare)
-
Metal-exchanged zeolites for NH3-SCR applications - Activity and Deactivation studies
- 2014
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Emissions of nitrogen oxides (NOX) formed during the burning process in internal combustion engines is a major contributor to global air pollutions. One effective way to reduce NOX in lean environments, i.e. oxygen excess is selective catalytic reduction with ammonia (NH3-SCR). Metal-exchanged zeolites have proven to be active as SCR catalysts, where copper and iron are the most common metals. When using metal-exchanged zeolites in exhaust aftertreatment systems, several challenges arise. Resistance towards hydrothermal deactivation and chemisorption of impurities on the active sites of the catalyst are two of the more important challenges. Temperatures between 600-700oC can be seen during regeneration of the particulate filter, which usually is placed upstream close to the SCR catalyst in the exhaust aftertreatment system, and therefore hydrothermal stability of the metal-exchanged zeolite is crucial. Furthermore, high tolerance against catalyst poisons which originate from (bio-) fuels and lubricating oils is desired, where phosphorous and potassium are among the more important poisons. In this thesis thermal and chemical deactivation of iron-exchanged zeolite BEA as SCR catalyst is experimentally studied with special focus paid on the active iron species. Based on the experimental results a kinetic model is developed to predict the decreased activity of the catalyst after deactivation. Several characterization techniques are used to evaluate and correlate structural changes in the catalyst with the decreased activity. Catalysts are prepared and characterized using BET, XPS, XRD, TPD, in-situ FTIR and UV-Vis. The catalytic performance of the samples is measured using a flow-reactor system.It is concluded that the hydrothermal deactivation of Fe-BEA is a result of migration of isolated iron species forming iron cluster inside the zeolite pores and iron particles located on the external surface of the zeolite crystals. Further, it is shown that the growth of iron clusters and particles can be partially reversed by high temperature hydrogen treatment. The chemical deactivation due to phosphorous exposure is the result of formation of metaphosphates replacing hydroxyl groups on the active isolated iron species. Furthermore, the chemical deactivation of Fe-BEA by potassium is concluded to be due to exchange and loss of active isolated iron species in the zeolite forming smaller iron clusters inside the zeolite pores.A kinetic model where different iron species are included was developed based on the hydrothermal deactivation experiments and validated using phosphorous and potassium exposed samples. By fitting and fix the kinetic parameters towards a fresh sample, the decreased SCR activity can be predicted by just decreasing the number of active iron sites, representing loss of active iron species due to hydrothermal treatment and poisoning.The effect of gas atmosphere during solid-state ion-exchange of copper-zeolites was studied as well. It is concluded that copper becomes highly mobile due to formation of copper-ammine complexes in presence of NH3 after reduction of CuII to CuI by adding NO in the exposing gas during the solid-state ion-exchange. Copper-exchanged zeolites could be prepared by exposing physical mixtures of copper-oxides with zeolites to NO and NH3 at as low temperature as 250oC.Finally, the ammonia formation during the rich period of NOX storage and reduction (NSR) cycles was studied using kinetic modeling for the possibility of combining NSR and SCR catalysts in the exhaust aftertreatment system. It is concluded that the formation of ammonia is due to stored NOX and hydrogen from the gas in the first half of the catalyst. However, it was further concluded that the formation of ammonia is delayed due to formation of N2O from stored NOX and formed NH3.
|
|
| 6. |
- Öhman, Sebastian, 1991-, et al.
(författare)
-
Selective kinetic growth and role of local coordination in forming Al2TiO5-based coatings at lower temperatures
- 2021
-
Ingår i: Materials Advances. - : Royal Society of Chemistry. - 2633-5409. ; 2:17, s. 5737-5751
-
Tidskriftsartikel (refereegranskat)abstract
- Negative thermal expansion is an elusive property found among certain materials, whose potential applications have remained limited due to the many challenges faced in their synthesis. Herein, we report the successful formation of aluminium titanate-based coatings (Al2TiO5), a material renowned for its low-to-negative thermal expansion, by the co-deposition of aluminium-isopropoxide and titanium-isopropoxide in a hot-wall chemical vapour deposition instrument. While coatings grown at 450 °C were amorphous as-deposited, a short-range order into the Al2TiO5-phase was found and analysed by using Raman spectroscopy. Upon subsequent annealing at 700 °C for 3 hours, crystalline coatings were achieved without forming any binary phases. The selective synthesis of the Al2TiO5 phase is ascribed to the precursors’ inherent chemical similarities, resulting in a kinetic targeting of this phase and a short-range homogeneity, entailing its preferred crystallisation. The role of local coordination is expressed by demonstrating the formation of intergrowth phases ascribed to lower coordinating interstices in the compound. Both the formation and crystallisation temperatures reported herein, as well as the timescales needed for the synthesises, are considerably lower than any conventional adopted solid-state techniques used so far to attain the Al2TiO5 phase.
|
|
| 7. |
- Kolavali, Reddysuresh, 1983, et al.
(författare)
-
The sorption of monovalent cations onto wood flour and holocelluloses of Norway spruce: molecular interactions during LiCl impregnation
- 2017
-
Ingår i: Holzforschung. - : Walter de Gruyter GmbH. - 1437-434X .- 0018-3830. ; 71:5, s. 373-381
-
Tidskriftsartikel (refereegranskat)abstract
- Active functional groups and interactions involved in the sorption of Li+ ions from an aqueous LiCl solution onto the Norway spruce sapwood (sW) flour have been investigated. To this purpose, sW was delignified by peracetic acid (PAA) treatments and the resulting holocelluloses (HC6 h, HC24 h, HC51 h, HC72 h, where the lower case data indicate the PAA treatment time) with various lignin contents were immersed in aqueous solution of LiCl and the sorption effects were studied by flame atomic emission spectroscopy (FAES), attenuated total reflectance-Fourier transform infrared spectroscopy (ATR-FTIR), and X-ray photoelectron spectroscopy (XPS). The Brunauer- Emmett-Teller (BET) specific surface area increased from 1.5±0.0 m2g−1 to 2.4±0.1 m2g−1 for HC6 h, and from 1.6±0.03 m2g−1 to 2.7±0.6 m2g−1 for HC72 h upon LiCl treatment. It was found that Li+/Cl− retention occurs predominantly via O-containing functionalities and the carbohydrate-rich samples sorbed more Li+. Upon LiCl treatment, the mobility and accessibility of the wood matrix was enhanced, possibly by interference of the introduced ions with the existing intermolecular bonds.
|
|
| 8. |
- Hassellöv, Martin, 1970, et al.
(författare)
-
REACH missar nano!
- 2009
-
Ingår i: Miljöforskning. ; 2009:3-4
-
Tidskriftsartikel (övrigt vetenskapligt/konstnärligt)
|
|
| 9. |
- Antonsen, Simen, et al.
(författare)
-
Atmospheric Chemistry of tert-butylamine and AMP
- 2017
-
Ingår i: Energy Procedia. Volume 114, 2017, Pages 1026-103213th International Conference on Greenhouse Gas Control Technologies, GHGT 2016; Lausanne; Switzerland; 14 November 2016 through 18 November 2016. - : Elsevier BV. - 1876-6102.
-
Konferensbidrag (refereegranskat)abstract
- © 2017 The Authors. The atmospheric chemistry of (CH 3 ) 3 CNH 2 (tert-butylamine, tBA) and (CH 3 ) 2 (CH 2 OH)CNH 2 (2-amino-2-methyl-1-propanol, AMP) has been studied by quantum chemistry methods and in photo-oxidation experiments in the EUPHORE chamber in Valencia (Spain). Aerosol formation and composition has been quantified. Yields of nitramines and other products in the photo-oxidations have been determined and complete photo-oxidation schemes including branching between the major reaction routes have been obtained. Published by Elsevier Ltd.
|
|
| 10. |
- Stedt, Kristoffer, 1991, et al.
(författare)
-
Post-harvest cultivation with seafood process waters improves protein levels of Ulva fenestrata while retaining important food sensory attributes
- 2022
-
Ingår i: Frontiers in Marine Science. - : Frontiers Media SA. - 2296-7745.
-
Tidskriftsartikel (refereegranskat)abstract
- Seaweed aquaculture can provide the growing human population with a sustainable source of proteins. Sea-based cultivation is an effective method for farming seaweeds on a large scale and can yield high biomass output. However, the quality and biochemical composition of the biomass is seasonally dependent, which limits the harvests to certain periods of the year. Here we show the possibility to extend the sea-based cultivation season of Ulva fenestrata when aiming for high protein levels, by post-harvest treatment in herring production process waters. We harvested U. fenestrata at an optimal period in terms of yield, but suboptimal in terms of protein content. We then cultivated the seaweed in onshore tank systems with the nutrient-rich process waters for 14 days. We monitored biomass yield, crude protein content, amino acid composition, and content of the health concerning metals arsenic, mercury, lead, and cadmium, as well as the sensory properties of the dried biomass. After cultivation in the process waters, biomass yields were 30 - 40% higher (210 – 230 g fresh weight) compared to in seawater (160 g fresh weight). Also, the crude protein and amino acid content increased three to five times in the process waters, reaching 12 - 17 and 15 – 21% dry weight, respectively. The protein enriched biomass followed food graded standards for heavy metal content, and consumption of the biomass does not exceed health based reference points. Additionally, no sensory attributes regarded as negative were found. This rapid, post-harvest treatment can help extend the cultivation season of sea-based seaweed farms, maximizing their output of sustainable proteins.
|
|
