| 1. |
|
|
| 2. |
- Wojas, Natalia
(författare)
-
The dynamic surface nature of calcite and its role in determining the adsorptive stability toward hydrophobizing carboxylic fatty acids
- 2021
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Calcium carbonate has attracted a lot of interest over the centuries. Nowadays, mainly as mineral pigment and filler, it has a wide use in technological applications ranging from paper, construction, polymers, and environmental solutions to consumer goods. Amongst these uses, the filler pigment is required to display either hydrophilicity (for applications in aqueous colloidal systems, including, for example, in paper and emulsion paints), or, in contrast, oleophilicity (for applications in contact with oil-based systems, such as plastics and volatile solvent-containing sealants). To achieve oleophilicity, and resulting hydrophobicity, the filler is surface treated, typically using carboxylic fatty acids. In this thesis, effects of humidity and fatty carboxylic acids vapor on CaCO3 surface wettability and nanomechanical properties were studied, with the aim to gain knowledge on layer packing density and order, as well as resistance to water exposure and mechanical wear. A better understanding of the dynamic nature of the calcite surface presented in this work allows the industry to increase sustainable control over materials production and storage. First, a setup combining an atomic force microscope (AFM) with a humidifier was used to map nanomechanical properties of growing surface domains (hydrated form of CaCO3) formed by ion dissolution, diffusion, and redeposition, a process that is not reversible upon drying. Secondly, AFM and contact angle goniometer measurements showed that the stability of the calcite surface improves with increasing carboxylic acid chain length (C2 to C18). Meanwhile, X-ray photoelectron spectroscopy and vibrational sum frequency spectroscopy techniques demonstrated that a coherent layer with maximum packing density of carboxylate and carboxylic acid species was achieved with the use of stearic acid (C18) with high enough vapor pressure and exposure time. The AFM images successfully visualized that a complete C18 monolayer is capable of countering nano-wear of the calcite surface despite the humidity (under the range of loads investigated in this work) and the layer has self-healing properties, while calcite displayed high abrasive wear. Further, when calcite coated by a highly packed monolayer of C18 was covered with a water droplet, a large contact angle hysteresis resulted in a coffee ring effect (CRE). That is leading to formation of hillocks at the contact line consisting of dissolved fatty carboxylic acid and possibly calcium bicarbonate Ca(HCO3)2 molecules transported from the bare calcite region that also is created next to the droplet edge. Interestingly, C18 coated calcite remained considerably more stable in the case where a water droplet saturated with octanoic acid was used instead of water; thus, it was concluded that the CRE can be contained via reduction of the liquid surface tension and contact angle hysteresis.
|
|
| 3. |
- Hedlund, Artur, et al.
(författare)
-
Microstructures of cellulose coagulated in water and alcohols from 1-ethyl-3-methylimidazolium acetate : contrasting coagulation mechanisms
- 2019
-
Ingår i: Cellulose. - : Springer Science and Business Media LLC. - 0969-0239 .- 1572-882X. ; 26:3, s. 1545-1563
-
Tidskriftsartikel (refereegranskat)abstract
- Abstract: Coagulation of cellulose solutions is a process whereby many useful materials with variable microstructures and properties can be produced. This study investigates the complexity of the phase separation that generates the structural heterogeneity of such materials. The ionic liquid, 1-ethyl-3-methylimidazolium acetate ([C2mim][OAc]), and a co-solvent, dimethylsulfoxide (DMSO), are used to dissolve microcrystalline cellulose in concentrations from 5 to 25 wt%. The solutions are coagulated in water or 2-propanol (2PrOH). The coagulated material is then washed and solvent exchanged (water → 2PrOH → butanone → cyclohexane) in order to preserve the generated microstructures upon subsequent drying before analysis. Sweep electron microscopy images of 50 k magnification reveal open-pore fibrillar structures. The crystalline constituents of those fibrils are estimated using wide-angle X-ray spectroscopy and specific surface area data. It is found that the crystalline order or crystallite size is reduced by an increase in cellulose concentration, by the use of the co-solvent DMSO, or by the use of 2PrOH instead of water as the coagulant. Because previous theories cannot explain these trends, an alternative explanation is presented here focused on solid–liquid versus liquid–liquid phase separations. Graphical abstract: [Figure not available: see fulltext.].
|
|
| 4. |
- Sepehri, Sobhan, 1986, et al.
(författare)
-
Characterization of Binding of Magnetic Nanoparticles to Rolling Circle Amplification Products by Turn-On Magnetic Assay
- 2019
-
Ingår i: Biosensors-Basel. - : MDPI AG. ; 9:3
-
Tidskriftsartikel (refereegranskat)abstract
- The specific binding of oligonucleotide-tagged 100 nm magnetic nanoparticles (MNPs) to rolling circle products (RCPs) is investigated using our newly developed differential homogenous magnetic assay (DHMA). The DHMA measures ac magnetic susceptibility from a test and a control samples simultaneously and eliminates magnetic background signal. Therefore, the DHMA can reveal details of binding kinetics of magnetic nanoparticles at very low concentrations of RCPs. From the analysis of the imaginary part of the DHMA signal, we find that smaller MNPs in the particle ensemble bind first to the RCPs. When the RCP concentration increases, we observe the formation of agglomerates, which leads to lower number of MNPs per RCP at higher concentrations of RCPs. The results thus indicate that a full frequency range of ac susceptibility observation is necessary to detect low concentrations of target RCPs and a long amplification time is not required as it does not significantly increase the number of MNPs per RCP. The findings are critical for understanding the underlying microscopic binding process for improving the assay performance. They furthermore suggest DHMA is a powerful technique for dynamically characterizing the binding interactions between MNPs and biomolecules in fluid volumes.
|
|
| 5. |
- Andersson Trojer, Markus, et al.
(författare)
-
Elastic strain-hardening and shear-thickening exhibited by thermoreversible physical hydrogels based on poly(alkylene oxide)-grafted hyaluronic acid or carboxymethylcellulose
- 2020
-
Ingår i: Physical Chemistry, Chemical Physics - PCCP. - : Royal Society of Chemistry. - 1463-9076 .- 1463-9084. ; 22:26, s. 14579-14590
-
Tidskriftsartikel (refereegranskat)abstract
- The formation of strongly elastic physical gels based on poly(alkylene oxide)-grafted hyaluronan or carboxymethylcellulose, exhibiting both shear-thickening and strain-hardening have been studied using rheometry and explained using a slightly different interpretation of the transient network theory. The graft copolymers were prepared by a quantitative coupling reaction. Their aqueous solutions displayed a thermoreversible continuous transition from Newtonian fluid to viscoelastic solid which could be controlled by the reaction conditions. The evolution of all material properties of the gel could be categorized into two distinct temperature regimes with a fast evolution at low temperatures followed by a slow evolution at high temperatures. The activation energy of the zero shear viscosity and the relaxation time of the graft inside the interconnecting microdomains were almost identical to each other in both temperature regimes. This suggests that the number of microdomains remained approximately constant whereas the aggregation number inside the microdomains increased according to the binodal curve of the thermosensitive graft.
|
|
| 6. |
- Nestorson, A., et al.
(författare)
-
Multivariate analysis of retention and distribution of aroma compounds in barrier dispersion coatings
- 2007
-
Ingår i: Packaging Technology and Science. - : Wiley InterScience. - 0894-3214 .- 1099-1522. ; 20:5, s. 345-358
-
Tidskriftsartikel (refereegranskat)abstract
- The influence of drying conditions, latex type, talc content and amount of added aroma compounds on the retention and distribution of aroma compounds in barrier dispersion coatings was explored using static headspace gas chromatography combined with multivariate data analysis. The model aroma system consisted of an alcohol, an ester, an aldehyde, a ketone and two terpenes. Four latex grades based on styrene-acrylate and styrene-butadiene were studied. It was found that non-polar aroma compounds were retained best in styrene-butadiene latex, while polar ones were retained more in the styrene-acrylate latex. Talc increased the retention of all the aroma compounds. The retention of polar compounds was higher with shorter drying times, which is probably due to greater losses during the later steps of the film formation process when internal water was evaporated. Polarity and talc also affected the partition of the aroma compounds between air and film.
|
|
| 7. |
- Skedung, Lisa, et al.
(författare)
-
Feeling small : Exploring the Tactile Perception Limits
- 2013
-
Ingår i: Scientific Reports. - : Springer Science and Business Media LLC. - 2045-2322. ; 3, s. 2617-
-
Tidskriftsartikel (refereegranskat)abstract
- The human finger is exquisitely sensitive in perceiving different materials, but the question remains as to what length scales are capable of being distinguished in active touch. We combine material science with psychophysics to manufacture and haptically explore a series of topographically patterned surfaces of controlled wavelength, but identical chemistry. Strain-induced surface wrinkling and subsequent templating produced 16 surfaces with wrinkle wavelengths ranging from 300 nm to 90 mu m and amplitudes between 7 nm and 4.5 mu m. Perceived similarities of these surfaces (and two blanks) were pairwise scaled by participants, and interdistances among all stimuli were determined by individual differences scaling (INDSCAL). The tactile space thus generated and its two perceptual dimensions were directly linked to surface physical properties - the finger friction coefficient and the wrinkle wavelength. Finally, the lowest amplitude of the wrinkles so distinguished was approximately 10 nm, demonstrating that human tactile discrimination extends to the nanoscale.
|
|
| 8. |
- Kuktaite, Ramune, et al.
(författare)
-
Monitoring Nanostructure Dynamics and Polymerization in Glycerol Plasticized Wheat Gliadin and Glutenin Films : Relation to Mechanical Properties
- 2016
-
Ingår i: ACS Sustainable Chemistry and Engineering. - : American Chemical Society (ACS). - 2168-0485. ; 4:6, s. 2998-3007
-
Tidskriftsartikel (refereegranskat)abstract
- Gliadin and glutenin proteins with 10, 20, 30 and 40% of glycerol were compression molded into films (130 °C) and evaluated for protein polymerization, β-sheet structure and nano-structural morphology. Here, for the first time we show how different amounts of glycerol impact the nano-structure and functional properties of the gliadin and glutenin films. Most polymerized protein was found in the gliadin films with 20 and 30% glycerol, and in all the glutenin films (except 10%), by RP-HPLC. A β-sheet-rich protein structure was found to be high in the 10 and 20% glycerol gliadin films, and in the 20 and 30% glycerol glutenin films by FT-IR. Glycerol content of 20, 30 and 40% impacted the nano-structural morphology of the gliadin glycerol films observed by SAXS, and to a limited extent for 10 and 20% glycerol gliadin films revealed by WAXS. No ordered nano-structure was found for the glutenin glycerol films. The 20%, 30% and 40% glycerol films were the most tunable for specific mechanical properties. For the highest stiffness and strength, the 10% glycerol protein films were the best choice.
|
|
| 9. |
- Li, Jing, et al.
(författare)
-
Towards the mechanism of electrochemical activity and self-healing of 1 wt% PTSA doped polyaniline in alkyd composite polymer coating : Combined AFM-based studies
- 2016
-
Ingår i: RSC Advances. - : Royal Society of Chemistry. - 2046-2069. ; 6:23, s. 19111-19127
-
Tidskriftsartikel (refereegranskat)abstract
- A composite solvent-borne alkyd coating with 1 wt% p-toluene sulfonic acid (PTSA) doped polyaniline (PANI) was prepared. The mechanisms of electrochemical activity and self-healing properties of the composite coating were investigated by in situ atomic force microscopy (AFM), intermodulation AFM (ImAFM), electrochemical controlled (EC)-AFM combined with cyclic voltammetry (CV), Kelvin force microscopy (KFM), and Fourier transform infrared spectroscopy (FTIR), as well as open-circuit potential (OCP) and electrochemical impedance spectroscopy (EIS) methods. The ImAFM demonstrates the multiphase structure of the composite coating and a high compatibility between the doped PANI and alkyd matrix. The CV and EC-AFM results reveal a high electrochemical activity of the doped PANI in the composite coating as well as reversible redox reactions between the emeraldine salt (ES) and leuco emeraldine base (LB) forms. The Volta potential mapping of KFM demonstrates a strong self-healing ability of the doped PANI in air conditions. The good electrochemical connection between the fine network of PANI in the composite coating and metal surface underneath enable the occurrence of reversible redox reaction between the ES/LB forms of doped PANI and a concomitant release of dopant anions both in air and in 3 wt% NaCl solution as demonstrated by OCP and EIS results. These therefore lead to the strong passivation and self-healing effect of the composite coated on the carbon steel surface.
|
|
| 10. |
- Roos, Sandra, 1977, et al.
(författare)
-
USEtox characterisation factors for textile chemicals based on a transparent data source selection strategy
- 2018
-
Ingår i: International Journal of Life Cycle Assessment. - : Springer Science and Business Media LLC. - 1614-7502 .- 0948-3349. ; 23:4, s. 890-903
-
Tidskriftsartikel (refereegranskat)abstract
- Purpose Life cycle assessments (LCAs) of textile products which do not include the use and emission of textile chemicals, such as dyes, softeners and water-repellent agents,will give non-comprehensive results for the toxicity impact potential. The purpose of this paper is twofold: (1) to provide a set of characterisation factors (CFs) for some of the most common textile chemicals and (2) to propose a data source selection strategy in order to increase transparency when calculating new CFs. Methods A set of 72 common textile-related substances was matched with the USEtox 2.01, USEtox 1.01 and the COSMEDE databases in order to investigate coverage and coherence. For the 25 chemicals that did not already have established CFs in any of these databases, new CFs were calculated. A data source selection strategy was developed and followed in order to ensure consistency and transparency,and USEtox 2.01 was used for calculations. The parameters that caused the most uncertainty were identified during the modelling and strategies for handling them were developed. Results and discussion Of the 72 textile-related substances, 48 already had calculated recommended or indicative CFs in existing databases, which showed good coherence. The main uncertainty identified during the calculation of 25 new CFs was the selection of input data regarding toxicity and degradation in water. However, for substances such as per- and polyfluoroalkyl substances (PFAS), the acid dissociation constant (pKa) and partitioning coefficients (Kow and KOC)also require special considerations. Other input parameters had less than one order of magnitude impact on the CF result for essentially all substances. Conclusions The paper presents a strategy for how to provide a complete set of toxicity CFs for a given list of substances. In addition, such a set of CFs for common textile-related substances is presented. The data source selection strategy provides a structured and transparent way of calculating additional CFs for textile chemicals with USEtox. Consequently, this study can help future LCA studies to provide relevant guidance towards environmentally benign chemical management in the textile industry.
|
|
