| 1. |
- Buckland, Philip I., 1973-, et al.
(författare)
-
The Strategic Environmental Archaeology Database : a resource for international, multiproxy and transdisciplinary studies of environmental and climatic change
- 2015
-
Konferensbidrag (refereegranskat)abstract
- Climate and environmental change are global challenges which require global data and infrastructure to investigate. These challenges also require a multi-proxy approach, integrating evidence from Quaternary science and archaeology with information from studies on modern ecology and physical processes among other disciplines. The Strategic Environmental Archaeology Database (SEAD http://www.sead.se) is a Swedish based international research e-infrastructure for storing, managing, analysing and disseminating palaeoenvironmental data from an almost unlimited number of analysis methods. The system currently makes available raw data from over 1500 sites (>5300 datasets) and the analysis of Quaternary fossil insects, plant macrofossils, pollen, geochemistry and sediment physical properties, dendrochronology and wood anatomy, ceramic geochemistry and bones, along with numerous dating methods. This capacity will be expanded in the near future to include isotopes, multi-spectral and archaeo-metalurgical data. SEAD also includes expandable climate and environment calibration datasets, a complete bibliography and extensive metadata and services for linking these data to other resources. All data is available as Open Access through http://qsead.sead.se and downloadable software. SEAD is maintained and managed at the Environmental Archaeology Lab and HUMlab at Umea University, Sweden. Development and data ingestion is progressing in cooperation with The Laboratory for Ceramic Research and the National Laboratory for Wood Anatomy and Dendrochronology at Lund University, Sweden, the Archaeological Research Laboratory, Stockholm University, the Geoarchaeological Laboratory, Swedish National Historical Museums Agency and several international partners and research projects. Current plans include expanding its capacity to serve as a data source for any system and integration with the Swedish National Heritage Board's information systems. SEAD is partnered with the Neotoma palaeoecology database (http://www.neotomadb.org) and a new initiative for building cyberinfrastructure for transdisciplinary research and visualization of the long-term human ecodynamics of the North Atlantic funded by the National Science Foundation (NSF).
|
|
| 2. |
- Åkerfeldt, Pia, et al.
(författare)
-
Electron backscatter diffraction characterization of fatigue crack growth in laser metal wire deposited Ti-6Al-4V
- 2018
-
Ingår i: Materials Characterization. - : Elsevier BV. - 1044-5803 .- 1873-4189. ; 135, s. 245-256
-
Tidskriftsartikel (refereegranskat)abstract
- By additive manufacturing (AM) there is a feasibility of producing near net shape components in basically one step from 3D CAD model to final product. The interest for AM is high and during the past decade a lot of research has been carried out in order to understand the influence from process parameters on the microstructure and furthermore on the mechanical properties. In the present study laser metal wire deposition of Ti-6Al-4V has been studied in detail with regard to its fatigue crack propagation characteristics. Two specimen orientations, parallel and perpendicular to the deposition direction, have been evaluated at room temperature and at 250 °C. No difference in the fatigue crack growth rate could be confirmed for the two specimen orientations. However, in the fractographic study it was observed that the tortuosity varied between certain regions on the fracture surface. The local crack path characteristic could be related to the alpha colony size and/or the crystallographic orientation. Moreover, large areas exhibiting similar crystallographic orientation were observed along the prior beta grain boundaries, which were attributed to the wide alpha colonies frequently observed along the prior beta grain boundaries. © 2017 Elsevier Inc.
|
|
| 3. |
- Wärmefjord, Kristina, 1976, et al.
(författare)
-
Welding of non-nominal geometries : physical tests
- 2016
-
Ingår i: Procedia CIRP. - : Elsevier BV. - 2212-8271 .- 2212-8271. ; 43, s. 136-141
-
Tidskriftsartikel (refereegranskat)abstract
- The geometrical quality of a welded assembly is to some extent depending part positions before welding. Here, a design of experiment is set up in order to investigate this relation using physical tests in a controlled environment. Based on the experimental results it can be concluded that the influence of part position before welding is significant for geometrical deviation after welding. Furthermore, a working procedure for a completely virtual geometry assurance process for welded assemblies is outlined. In this process, part variations, assembly fixture variations and welding induced variations are important inputs when predicting the capability of the final assembly.
|
|
| 4. |
- Chen, Zhe, et al.
(författare)
-
Nano-scale characterization of white layer in broached Inconel 718
- 2017
-
Ingår i: Materials Science & Engineering A: Structural Materials: Properties, Microstructure and Processing. - Amsterdam : Elsevier BV. - 0921-5093 .- 1873-4936. ; 684, s. 373-384
-
Tidskriftsartikel (refereegranskat)abstract
- The formation mechanism of white layers during broaching and their mechanical properties are not well investigated and understood to date. In the present study, multiple advanced characterization techniques with nano-scale resolution, including transmission electron microscopy (TEM), transmission Kikuchi diffraction (TKD), atom probe tomography (APT) as well as nano-indentation, have been used to systematically examine the microstructural evolution and corresponding mechanical properties of a surface white layer formed when broaching the nickel-based superalloy Inconel 718.TEM observations showed that the broached white layer consists of nano-sized grains, mostly in the range of 20–50 nm. The crystallographic texture detected by TKD further revealed that the refined microstructure is primarily caused by strong shear deformation. Co-located Al-rich and Nb-rich fine clusters have been identified by APT, which are most likely to be γ′ and γ′′ clusters in a form of co-precipitates, where the clusters showed elongated and aligned appearance associated with the severe shearing history. The microstructural characteristics and crystallography of the broached white layer suggest that it was essentially formed by adiabatic shear localization in which the dominant metallurgical process is rotational dynamic recrystallization based on mechanically-driven subgrain rotations. The grain refinement within the white layer led to an increase of the surface nano-hardness by 14% and a reduction in elastic modulus by nearly 10% compared to that of the bulk material. This is primarily due to the greatly increased volume fraction of grain boundaries, when the grain size was reduced down to the nanoscale.
|
|
| 5. |
- Dimitrios, Nikas, et al.
(författare)
-
Effect of annealing on microstructure in railway wheel steel
- 2022
-
Ingår i: 42Nd Riso International Symposium On Materials Science. - : Institute of Physics Publishing (IOPP). ; 1249
-
Konferensbidrag (refereegranskat)abstract
- Railway wheels are commonly made from medium carbon steels (similar to 0.55 wt.% C), heat treated to a near pearlitic microstructure with 5-10% pro-eutectoid ferrite. During the operation of freight trains, where block brakes are used, high thermal loads occur together with the high contact stresses, which combined can affect the mechanical properties of the material. In this study, the effects of annealing on local microstructure and mechanical properties in pearlitic railway wheel steel were investigated using electron microscopy and micro-hardness. It is found that after annealing at 650 degrees C, the room temperature hardness reduces about 25%, accompanied by significant spheroidization of cementite in the pearlitic colonies, though the size and the orientation gradients of the pearlitic colonies have not changed much. The relationship between the microstructural changes and the mechanical properties are discussed.
|
|
| 6. |
- Sefer, Birhan, 1983-, et al.
(författare)
-
Chemical Milling of Cast Ti-6Al-4V and Ti-6Al-2Sn-4Zr-2Mo Alloys in Hydrofluoric-Nitric Acid Solutions
- 2017
-
Ingår i: Corrosion. - : Association for Materials Protection and Performance (AMPP). - 0010-9312 .- 1938-159X. ; 73:4, s. 394-407
-
Tidskriftsartikel (refereegranskat)abstract
- The behavior of cast Ti-6Al-4V and Ti-6Al-2Sn-4Zr-2Mo during chemical milling in hydrofluoric-nitric (HF-HNO3) acid solutions with 1:3 and 1:11 molar ratios was investigated using electrochemical and atomic force microscopy (AFM) techniques. Faster corrosion rate in 1:3 solutions was measured for Ti-6Al-4V than for Ti-6Al-2Sn-4Zr-2Mo, whereas in 1:11 solution Ti-6Al-2Sn-4Zr-2Mo exhibited higher corrosion rate. Scanning Kelvin probe force microscopy measurements revealed difference in the Volta potential between the α-laths and the β-layers in the Widmansttäten microstructure indicating operation of microgalvanic cells between the microconstituents when in contact with HF-HNO3 solution. The AFM topography measurements demonstrated faster corrosion of the α-laths compared to the β-layers, in both alloys. In 1:3 solutions, higher α/β height difference was measured in Ti-6Al-4V, whereas in 1:11 solution, the difference was higher in Ti-6Al-2Sn-4Zr-2Mo. The results revealed that the chemical milling behavior of the two investigated alloys is controlled by the microscopic corrosion behavior of the individual microconstituents.
|
|
| 7. |
- Grolig, Jan Gustav, 1986
(författare)
-
Coated Ferritic Stainless Steels as Interconnects in Solid Oxide Fuel Cells - Material Development and Electrical Properties
- 2015
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Solid oxide fuel cells (SOFCs) are attracting increasing interest as devices with potentialuses in decentralized and clean electricity and heat production. Several challengeswith respect to materials have to be overcome to achieve efficiencies and life-spansthat are sufficient for long-term applications.An important element of an SOFC stack is the interconnect component, which connectstwo adjacent fuel cell elements. Interconnects, which are commonly composedof ferritic stainless steels, have to be corrosion-resistant, mechanically stable and costoptimized.This work aimed to investigate economic solutions for interconnect materials and tounderstand the underlying mechanisms of degradation and electrical conduction ofthese materials. Mainly two substrates, a commercially available steel (AISI 441) anda ferritic stainless steel that was optimized for an SOFC application (Sandvik SanergyHT) were combined with different barrier coatings and exposed to a cathode-sideatmosphere. A method was developed that allows for the electrical characterizationof promising material systems and model alloys, thereby facilitating a fundamentalunderstanding of the dominant electrical conduction processes linked to the oxidescales that grow on interconnects. The AISI 441 steel coated with reactive elementsand cobalt showed good corrosion and chromium evaporation profiles, while AISI 441coated with cerium and cobalt also had promising electrical properties. The SanergyHT steel was examined with coatings of copper and iron and copper and manganese,respectively. The corrosion and chromium evaporation profiles of Sanergy HT wereimproved by coating with copper and iron. The copper and iron-coated Sanergy HTshowed lower area specific resistance values than cobalt-coated Sanergy HT. Chromia,which is the main constituent of oxide scales, was synthesized using differentmethods. The electrical properties of chromia were found to be sensitive to not onlyimpurities, but also heat treatment. Finally the electrical properties of cobalt- andcobalt cerium-coated Sanergy HT steels were investigated. It was revealed that theaddition of cerium improved the conductivity of the interconnect by both slowingdown chromia growth and preventing the outward diffusion of iron into the spinel.
|
|
| 8. |
- Neikter, Magnus, et al.
(författare)
-
Microstructure and Defects in Additive Manufactured Titanium : a Comparison Between Microtomography and Optical Microscopy
- 2017
-
Konferensbidrag (övrigt vetenskapligt/konstnärligt)abstract
- The aim of this work has been to compare two different analysing methods; x-ray microtomography and light optical microscopy, when it comes to defects and microstructure of additively manufactured Ti-6Al-4V. The results show that both techniques have their pros and cons:microtomography is the preferred choice for defect detection by analysing the full 3D sample volume, while light optical microscopy is better for analysing finer details in 2D.
|
|
| 9. |
- Krakhmalev, Pavel, 1973-, et al.
(författare)
-
Microstructure, solidification texture, and thermal stability of 316 L stainless steel manufactured by laser powder bed fusion
- 2018
-
Ingår i: Metals. - : MDPI AG. - 2075-4701. ; 8:8, s. 1-18
-
Tidskriftsartikel (refereegranskat)abstract
- This article overviews the scientific results of the microstructural features observed in 316 L stainless steel manufactured by the laser powder bed fusion (LPBF) method obtained by the authors, and discusses the results with respect to the recently published literature. Microscopic features of the LPBF microstructure, i.e., epitaxial nucleation, cellular structure, microsegregation, porosity, competitive colony growth, and solidification texture, were experimentally studied by scanning and transmission electron microscopy, diffraction methods, and atom probe tomography. The influence of laser power and laser scanning speed on the microstructure was discussed in the perspective of governing the microstructure by controlling the process parameters. It was shown that the three-dimensional (3D) zig-zag solidification texture observed in the LPBF 316 L was related to the laser scanning strategy. The thermal stability of the microstructure was investigated under isothermal annealing conditions. It was shown that the cells formed at solidification started to disappear at about 800 °C, and that this process leads to a substantial decrease in hardness. Colony boundaries, nevertheless, were quite stable, and no significant grain growth was observed after heat treatment at 1050 °C. The observed experimental results are discussed with respect to the fundamental knowledge of the solidification processes, and compared with the existing literature data.
|
|
| 10. |
- Hosseini, Seyedehsan, 1994
(författare)
-
Additive-Driven Improvements in Interfacial Properties and Processing of TMP-Polymer Composites
- 2023
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Efforts to address environmental concerns have resulted in new regulations designed to plan the reduction of plastic and synthetic polymer usage, necessitating the search for sustainable natural alternatives with comparable cost-effectiveness and mechanical performance. Thermomechanical pulp (TMP) fibres are one of the most affordable natural fibres that have no chemical refining in production, production have a high yield of 90-98% and TMP fibres have been demonstrated to improve the mechanical characteristics (strength, stiffness and toughness) of wood-polymer composites (WPCs) compared to the pure polymer. The integration of TMP fibres with non-polar synthetic polymers remains a challenge due to surface polarity differences. This PhD thesis aims to ease the processing of TMP fibre composites through the incorporation of additives. The hypothesis posits that incorporating magnesium stearate (MgSt), molybdenum disulfide (MoS2) and alkyl ketene dimer (AKD) as additives in TMP composites will enhance interfacial properties, resulting in improved processability and flow behaviour at high temperatures. MoS2 is known for its interaction with lignin, which exists in TMP and MgSt is recognised for its ability to improve flow in pharmaceutical processing when combined with cellulose, also a component of TMP. AKD modifies the hydrophilic properties of lignocellulosic surfaces. The experimental work explores the effect of these additives on the properties of TMP composites of ethylene acrylic acid copolymer (EAA) and polypropylene (PP) matrices. The dynamic mechanical analysis (DMA) and mechanical analysis results reveal that MoS2 exhibits superior interaction with TMP fibres, yielding enhanced interfacial properties compared to MgSt in between EAA and TMP fibres. Rheological studies elucidate the transition from a fluid-like state to a network-like structure upon the incorporation of TMP into the PP matrix. The incorporation of AKD with C18 reduces the viscosity of TMP-PP composites and PP itself, and, as determined through theoretical Hansen solubility parameter (HSP) calculations, increases compatibility between cellulose in TMP fibres and PP. The addition of AKD influences both the colour (lighter) and shape (smoother surface) of the extrudate filaments in the TMP-PP composites, indicative of improved processing. In addition, frictional analysis demonstrates the reduction of the coefficient of friction (COF) between metal and TMP fibre by MgSt and AKD treatments.
|
|
