| 1. |
- Calmunger, Mattias
(författare)
-
High-Temperature Behaviour of Austenitic Alloys : Influence of Temperature and Strain Rate on Mechanical Properties and Microstructural Development
- 2013
-
Licentiatavhandling (övrigt vetenskapligt/konstnärligt)abstract
- The global increase in energy consumption and the global warming from greenhouse gas emission creates the need for more environmental friendly energy production processes. Biomass power plants with higher efficiency could generate more energy but also reduce the emission of greenhouse gases, e.g. CO2. Biomass is the largest global contributor to renewable energy and offers no net contribution of CO2 to the atmosphere. One way to increase the efficiency of the power plants is to increase temperature and pressure in the boiler parts of the power plant.The materials used for the future biomass power plants, with higher temperature and pressure, require improved properties, such as higher yield strength, creep strength and high-temperature corrosion resistance. Austenitic stainless steels and nickel-base alloys have shown good mechanical and chemical properties at the operation temperatures of today’s biomass power plants. However, the performance of austenitic stainless steels at the future elevated temperatures is not fully understood.The aim of this licentiate thesis is to increase our knowledge about the mechanical performance of austenitic stainless steels at the demanding conditions of the new generation power plants. This is done by using slow strain rate tensile deformation at elevated temperature and long term hightemperature ageing together with impact toughness testing. Microscopy is used to investigate deformation, damage and fracture behaviours during slow deformation and the long term influence of temperature on toughness in the microstructure of these austenitic alloys. Results show that the main deformation mechanisms are planar dislocation deformations, such as planar slip and slip bands. Intergranular fracture may occur due to precipitation in grain boundaries both in tensile deformed and impact toughness tested alloys. The shape and amount of σ-phase precipitates have been found to strongly influence the fracture behaviour of some of the austenitic stainless steels. In addition, ductility is affected differently by temperature depending on alloy tested and dynamic strain ageing may not always lead to a lower ductility.
|
|
| 2. |
- Gustafsson, David, 1983-
(författare)
-
Constitutive and fatigue crack propagation behaviour of Inconel 718
- 2010
-
Licentiatavhandling (övrigt vetenskapligt/konstnärligt)abstract
- In this licentiate thesis the work done in the TURBO POWER project Influence of high temperature hold times on the fatigue life of nickel-based superalloys will be presented. The overall objective of this project is to develop and evaluate tools for designing against fatigue in gas turbine applications, with special focus on the nickel-based superalloy Inconel 718. Firstly, the constitutive behaviour of the material has been been studied, where focus has been placed on trying to describe the mean stress relaxation and initial softening of the material under intermediate temperatures. Secondly, the fatigue crack propagation behaviour under high temperature hold times has been studied. Focus has here been placed on investigating the main fatigue crack propagation phenomena with the aim of setting up a basis for fatigue crack propagation modelling.This thesis is divided into two parts. The first part describes the general framework, including basic constitutive and fatigue crack propagation behaviour as well as a theoretical background for the constitutive modelling of mean stress relaxation. This framework is then used in the second part, which consists of the four included papers.
|
|
| 3. |
- Lundström, Erik
(författare)
-
Modelling of fatigue crack propagation in Inconel 718 under hold time conditions
- 2014
-
Licentiatavhandling (övrigt vetenskapligt/konstnärligt)abstract
- In this thesis an investigation and modelling of the fatigue crack propagation in the nickel based superalloy Inconel 718, with a special emphasis on the effect of hold times, is presented. The modelling work has been concentrated on describing the hold time fatigue crack propagation by using the concept of a damaged zone in front of the crack tip, which is believed to have a lowered resistance against crack propagation.The modelling framework is built on physically motivated parameters, which are all easy to calibrate through one specially designed test type. Later evaluation through many experimental tests has also shown that the model is capable, within reasonable scatter level to predict, the hold time fatigue crack propagation for many different temperatures and loading conditions. Further evaluation of a complex flight spectrum, with the incorporation of crack closure within the model, was also predicted with a satisfying result.This thesis is divided into two parts. First, a background and a somewhat deeper discussion of the modelling of fatigue crack growth under hold time conditions is presented. The second part consists of ve appended papers, which describe the work completed so far in the project.
|
|
| 4. |
- Segersäll, Mikael
(författare)
-
Nickel-Based Single-Crystal Superalloys : the crystal orientation influence on high temperature properties
- 2013
-
Licentiatavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Superalloys are a group of materials that are used in high temperature applications, for example gas turbines and aero engines. Gas turbines are most commonly used for power generation, and it is only the very critical components which are exposed to the most severe conditions within the turbine, which are made from superalloy material.Today, energy consumption in many parts of the world is very high and is tending to increase. This implies that all power generating sources, including gas turbines, must aim for higher efficiency. For the gas turbine industry, it is a continuous challenge to develop more energy-efficient turbines. One way to do this is to increase the temperature within the hot stage of the turbine. However, increased temperature in the hot stage also challenges the materials that are used there. Today’s materials are already pushed to the limit, i.e. they cannot be exposed to the temperatures which are required to further increase the turbine efficiency. To solve this problem, research which later can lead to better superalloys that can withstand even higher temperatures, has to be conducted within the area of superalloys.The aim of this licentiate thesis is to increase our knowledge about deformation and damage mechanisms that occur in the microstructure in superalloys when they are subjected to high temperatures and loads. This knowledge can later be used when developing new superalloys. In addition, increased knowledge of what is happening within the material when it is exposed to those severe conditions, will facilitate the development of material models. Material models are used for FEM simulations, when trying to predict life times in gas turbine components during the design process.This licentiate thesis is based on results from thermomechanical fatigue (TMF) testing of Ni-based single-crystal superalloys. Results show that the deformation within the microstructure during TMF is localized to several deformation bands. In addition, the deformation mechanisms are mainly twinning and shearing of the microstructure. Results also indicate that TMF cycling seems to influence the creep rate of single-crystal superalloys.
|
|
