| 1. |
- Ajjan Godoy, Fátima Nadia
(författare)
-
Biohybrid Polymer Electrodes for Renewable Energy Storage
- 2017
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Daily and seasonally fluctuating energy supply and demand requires adequate energy storage solutions. In recent years electrochemical supercapacitors have attracted considerable attention due to their ability to both store and deliver electrical energy efficiently. Our efforts are focused on developing and optimizing sustainable organic electrode materials for supercapacitors based on renewable bioorganic materials, offering a cheap, environmentally friendly and scalable alternative to store energy. In particular, we are using the second most abundant biopolymer in nature, lignin (Lig), which is an insulating material. However, when used in combination with electroactive and conducting polymers such as polypyrrole (PPy) and poly(3,4-ethylenedioxythiophene) (PEDOT), the biohybrid electrodes PPy/Lig and PEDOT/Lig display significantly enhanced energy storage performance as compared to the pristine conducting polymers without the lignin. Redox cyclic voltammetry and galvanostatic charge/discharge measurements indicate that the enhanced performance is due to the additional pseudocapacitance generated by the quinone moieties in lignin. Moreover, a conjugated redoxpolymer poly(aminoanthraquinone) PAAQ, with intrinsic quinone functions and excellentstability, has been combined with lignin and PEDOT resulting in a trihybrid bioelectrode. PEDOT compensates the low conductivity of PAAQ and provides electrical pathways to the quinone groups. The electrochemically generated quinones undergo a two electron, two protonredox process within the biohybrid electrodes as revealed by FTIR spectroelectrochemistry.These remarkable features reveal the exciting potential of a full organic energy storage device with long cycle life. Therefore, supercapacitor devices were designed in symmetric or asymmetric two electrode configuration. The best electrochemical performance was achieved by the asymmetric supercapacitor based on PEDOT+Lignin/PAAQ as the positive electrode and PEDOT/PAAQ as the negative electrode. This device exhibits superior electrochemical performance and outstanding stability after 10000 charge/discharge cycles due to the synergistic effect of the two electrodes. Finally, we have characterized the response of this supercapacitor device when charged with the intermittent power supply from an organic photovoltaic module. We have designed charging/discharging conditions such that reserve power was available in the storage device at all times. This work has resulted in an inexpensive fully organic system witht he dual function of energy conversion and storage.
|
|
| 2. |
- Andersson, Lars Mattias, 1976-
(författare)
-
Electronic Transport in Polymeric Solar Cells and Transistors
- 2007
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- The main topic of this dissertation is electronic charge transport in polymeric and molecular organic materials and material blends intended for solar cell applications. Charge transport in polymers is a strange beast and carrier mobility is rarely a well-defined number. Measurements on different sample geometries and under different conditions tend to give different results and when everything is to be related to solar cell performance it is imperative that there is a way to correlate the results from different measurements. Polymer solar cells utilize composite materials for their function. This puts an additional twist on charge transport studies, as there will also be interaction between the different phases to take into account.Several measurement techniques have been used and their interrelationships as well as information on their relevance for solar cells have been investigated. Field effect transistors (FET) with an organic active layer have proved to be one of the more versatile measurement geometries and are also an interesting topic in itself. FETs are discussed both as a route for material characterization and as components. A main result correlates bias stress in organic field effect transistors with the electronic structure of the material.Power conversion efficiency in solar cells is discussed with respect to electrical properties. The interaction of different blend materials and the impact of stoichiometry on transport properties in the active layer have been investigated. Results indicate that charge transport properties frequently are a key determining factor for which material combinations and ratios that works best.Some work on the conductive properties of nano-fibers coated with semiconducting polymers has also been done and is briefly discussed. The conductive properties of nano-fibers have been studied through potential imaging.
|
|
| 3. |
- Andersson, Mattias, 1973-
(författare)
-
Colour Calibration of Trichromatic Capturing Devices
- 2006
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- In a time where there is an increasing demand for easily accessible and up-to-date information, digital printing has become a link between traditional printed media and electronic media. Over the last years, applications such as variable data printing, personalised printing and print on demand have changed the way in which printed matter is produced and handled. The print quality of products produced by digital printing systems has improved considerably in recent years. The main reason for this improvement is better printer hardware but the printing paper is still a very influential factor. The two major technologies, inkjet and electrophotography and their respective applications put very different demands on the paper, mechanically, chemically and optically. Nevertheless, the differences in print quality across digital printing systems are decreasing, except for one area − colour reproduction. The growth of the market of consumer colour imaging products, such as digital printers and desktop printers, has been enormous during the last years. As a consequence of this, consumer expectations on colour reproduction have risen significantly, as even very small failures in colour reproduction can drastically reduce the visual impression of an otherwise impeccably reproduced image. Therefore, as consumer expectations continue to rise, a high and repeatable quality of colour image reproduction is a growing challenge for producers of digital printing devices as well as for paper producers. However, this is impossible to achieve without precise methods and routines to measure colour reproduction quality. The use of spectrophotometers for colour measurements of printed substrates is widely spread among paper producers as well as within the printing industry. Spectrophotometers are precise instruments for point-wise measurements. However, the measurement procedure is very time-consuming and therefore, faster methods for colour measurements are longed-for. If the spectrophotometers used today could be replaced with trichromatic capturing devices such as flatbed scanners or digital cameras, colour characterisation would be not only faster, but also less expensive. In addition, if the trichromatic devices are colorimetrically calibrated, spatial image information can be combined with colour information, making it possible to measure quality attributes related to colour image rendering that are impossible to capture with point-wise measurements. Today, flatbed scanners and digital cameras provide robust and high-quality image capturing capabilities at a relatively low cost. Furthermore, scanner and camera-based systems for automated objective measurements of print quality parameters have already become widely used tools for print quality measurements of print-related properties such as print mottle, sharpness and bleeding. However, the colour calibration of trichromatic capturing devices is not free from obstacles. In colour calibrations, where the aim is to measure colour of printed matter, knowledge about the properties of the capturing device, the printing substrate, the printing process and the printer function are all of great importance. In the work presented here, methods for colour characterisation of printing processes are proposed as well as methods for colour characterisation and calibration of trichromatic capturing devices. Furthermore, the media dependency problem inherent to colour calibrations of trichromatic capturing devices is discussed. Examples are given on how properties of the printed substrate, such as the content of fluorescent whitening agents, influence colour calibrations as well as colour measurements in general.
|
|
| 4. |
- Andersson, Viktor
(författare)
-
Electron tomography and optical modelling for organic solar cells
- 2012
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Organic solar cells using carbon based materials have the potential to deliver cheap solar electricity. The aim is to be able to produce solar cells with common printing techniques on flexible substrates, and as organic materials can be made soluble in various solvents, they are well adapted to such techniques. There is a large variation of organic materials produced for solar cells, both small molecules and polymers. Alterations of the molecular structure induce changes of the electrical and optical properties, such as band gap, mobility and light absorption. During the development of organic solar cells, the step of mixing of an electron donor and an electron acceptor caused a leap in power conversion efficiency improvement, due to an enhanced exciton dissociation rate. Top performing organic solar cells now exhibit a power conversion efficiency of over 10%. Currently, a mix of a conjugated polymer, or smaller molecule, and a fullerene derivative are commonly used as electron donor and acceptor. Here, the blend morphology plays an important role. Excitons formed in either of the donor or acceptor phase need to diffuse to the vicinity of the donor-acceptor interface to efficiently dissociate. Exciton diffusion lengths in organic materials are usually in the order of 5-10 nm, so the phases should not be much larger than this, for good exciton quenching. These charges must also be extracted, which implies that a network connected to the electrodes is needed. Consequently, a balance of these demands is important for the production of efficient organic solar cells.Morphology has been found to have a significant impact on the solar cell behaviour and has thus been widely studied. The aim of this work has been to visualize the morphology of active layers of organic solar cells in three dimensions by the use of electron tomography. The technique has been applied to materials consisting of conjugated polymers blended with fullerene derivatives. Though the contrast in these blends is poor, three-dimensional reconstructions have been produced, showing the phase formation in three dimensions at the scale of a few nanometres. Several material systems have been investigated and preparation techniques compared.Even if excitons are readily dissociated and paths for charge extraction exist, the low charge mobilities of many materials put a limit on film thickness. Although more light could be absorbed by increased film thickness, performance is hampered due to increased charge recombination. A large amount of light is thus reflected and not used for energy conversion. Much work has been put into increasing the light absorption without hampering the solar cell performance. Aside from improved material properties, various light trapping techniques have been studied. The aim is here to increase the optical path length in the active layer, and in this way improve the absorption without enhanced extinction coefficient.At much larger dimensions, light trapping in solar cells with folded configuration has been studied by the use of optical modelling. An advantage of these V-cells is that two materials with complementing optical properties may be used together to form a tandem solar cell, which may be connected in either serial or parallel configuration, with maintained light trapping feature. In this work optical absorption in V-cells has been modelled and compared to that of planar ones.
|
|
| 5. |
- Bergqvist, Jonas, 1983-
(författare)
-
Optoelectrical Imaging Methods for Organic Photovoltaic Materials and Moduls
- 2015
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- To achieve a high living standard for all people on Earth access to low cost energy is essential. The massive burning of fossil fuels must be drastically reduced if we are to avoid large changes of our climate. Solar cells are both technologically mature and have the potential to meet the huge demand for renewable energy in many countries. The prices for silicon solar cells have decreased rapidly during the course of this thesis and are now in grid parity in many countries.However, the potential for even lower energy costs has driven the research on polymer solar cells, a class of thin film solar cells. Polymer solar cells can be produced by roll to roll printing which potentially enables truly low cost solar cells. However, much research and development remain to reach that target.Polymer solar cells consist of a semiconducting composite material sandwiched between two electrodes, of which one is transparent, to let the light energy in to the semiconductor where it is converted to electric energy. The semiconductor comprise an intimate blend of polymer and fullerenes, where the nanostructure of this blend is crucial for the photo current extraction.To reach higher solar cell performance the dominating strategy is development and fine tuning of new polymers. To estimate their potential as solar cell materials their optical response have been determined by spectroscopic ellipsometry. Furthermore, optical simulations have been performed where the direction dependency of the optical response of the transparent electrode material PEDOT:PSS have been accounted for. The simulations show reduced electrode losses for light incident at large oblique angles.Moreover, we have shown that a gentle annealing of the active layer induces a local conformational changes of an amorphous polymer that is beneficial for solar cell performance. The active layer is deposited from solution where the drying kinetics determine the final nanostructure. We have shown that using in-situ photoluminescence phase separation can be detected during the drying process while a reflectance method have been developed to image lateral variations of solvent evaporation rate.Imaging methods are important tools to detect performance variations over the solar cell area. For this purpose an intermodulation based photo current imaging method have been developed to qualitatively differentiate the major photo current loss mechanisms. In addition, a 1D LED-array photo current imaging method have been developed and verified for high speed in-line characterization of printed organic solar modules.
|
|
| 6. |
- Björk, Per, 1978-
(författare)
-
Biological Sensing and DNA Templated Electronics Using Conjugated Polymers
- 2007
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Conjugated polymers have been found useful in a wide range of applications such as solar cells, sensor elements and printed electronics, due to their optical and electronic properties. Functionalization with charged side chains has enabled water solubility, resulting in an enhanced interaction with biomolecules. This thesis focus on the emerging research fields, where these conjugated polyelectrolytes (CPEs) are combined with biomolecules for biological sensing and DNA nanowire assembling.CPEs have shown large potential in biomolecular detection where the optical read out is due to the geometrical alternation in the backbone and aggregation state. This thesis focused on transferring the biomolecular detection to a surface of CPEs. The characterization of the CPE layer show that a hydrogel can be formed, and how the layer can undergo geometrical changes upon external stimulus such as pH change. A selective sensor surface can be created by imprinting ssDNA or an antibody in the CPE layer. The discrimination for complementary DNA hybridization and specific antibody interaction can be monitored by surface plasmon resonance or quartz crystal microbalance. We have also taken the step out from the controlled test tube experiments to the complex environment of the cell showing the potential for staining of compartments and structures in live and fixed cell. Depending on the conditions and CPE used, cell nuclei, acidic vesicles and cytoskeleton structure can be visualized. Furthermore, the live staining shows no sign of toxic effect on cultured fibroblasts.CPEs can also be a valuable element when assembling electronics in the true nano regime. I have used DNA as building template due to its attractive size features, with a width of around 2 nm and a length scale in the µm regime, and the inbuilt base-paring recognition elements. This thesis shows how DNA can be decorated with CPEs and stretched on surfaces into a model for aligned semiconducting nanowire geometries. Not only making the template structures is of importance, but also how to place them on the correct surface position, i.e. on electrodes. Strategies for positioning DNA nanowires using transfer printing and surface energy patterning methods have therefore been developed in the thesis. The stretched DNA decorated with CPE also offers a way to further study the molecular binding interaction between the two molecules. Single molecular spectroscopy in combination with polarization has given information of the variation of the CPE binding along a DNA chain.
|
|
| 7. |
- Bäcklund, Fredrik
(författare)
-
Preparation and Application of Functionalized Protein Fibrils
- 2015
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Many proteins have an innate ability to self-assemble into fibrous structures known as amyloid fibrils. From a material science perspective, fibrils have several interesting characteristics, including a high stability, a distinct shape and tunable surface properties. Such structures can be given additional properties through functionalization by other compounds such as fluorophores. Combination of fibrils with a function yielding compound can be achieved in several ways. Covalent bond attachment is specific, but cumbersome. External surface adhesion is nonspecific, but simple. However, in addition, internal non-covalent functionalization is possible. In this thesis, particular emphasis is put on internal functionalization of fibrils; by co-grinding fibril forming proteins with a hydrophobic molecule, a protein-hydrophobic compound molecule composite can be created that retains the proteins innate ability to form fibrils. Subsequently formed fibrils will thus have the structural properties of the protein fibril as well as the properties of the incorporated compound. The functionalization procedures used throughout this thesis are applicable for a wide range of chromophores commonly used for organic electronics and photonics. The methods developed and the prepared materials are useful for applications within optoelectronics as well as biomedicine.Regardless of the methodology of functionalization, using functionalized fibrils in a controlled fashion for material design requires an intimate understanding of the formation process and knowledge of the tools available to control not only the formation but also any subsequent macroscale assembly of fibrils. The development and application of such tools are described in several of the papers included in this thesis. With the required knowledge in hand, the possible influence of fibrils on the functionalizing agents, and vice versa, can be probed. The characteristic traits of the functionalized fibril can be customized and the resulting material can be organized and steered towards a specific shape and form. This thesis describes how control over the process of formation, functionalization and organization of functionalized fibrils can be utilized to influence the hierarchical assembly of fibrils – ranging from spherical structures to spirals; the function – fluorescent or conducting; and macroscopic properties – optical birefringence and specific arrangement of functionalized fibrils in the solid state. In conclusion, the use of amyloid fibrils in material science has great potential. Herein is presented a possible route towards a fully bottom up approach ranging from the nanoscale to the macroscale.
|
|
| 8. |
- Felekidis, Nikolaos, 1985-
(författare)
-
Effects of Energetic Disorder on the Optoelectronic Properties of Organic Solar Cells
- 2018
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Organic photovoltaics (OPVs) is a promising low-cost and environmental-friendly technology currently achieving 12-14% power conversion efficiency. Despite the extensive focus of the research community over the last years, critical mechanisms defining the performance of OPVs are still topics of debate. While energetic disorder is known to be characteristic of organic semiconductors in general, its potential role in OPV has received surprisingly little attention. In this thesis we investigate some aspects of the relation between energetic disorder and several optoelectronic properties of OPV.Charge carrier mobility is a key parameter in characterizing the performance of organic semiconductors. Analyzing the temperature dependence of the mobility is also an oftenused method to obtain (estimates for) the energetic disorder in the HOMO and LUMO levels of an organic semiconductor material. Different formalisms to extract and analyze mobilities from space charge limited conductivity (SCLC) experiments are reviewed. Surprisingly, the Murgatroyd-Gill analytical model in combination with the Gaussian disorder model in the Boltzmann limit yields similar mobilities and energetic disorders as a more elaborate drift-diffusion model with parametrized mobility functionals. Common analysis and measurement errors are discussed. All the models are incorporated in an automated analysis freeware tool.The open circuit voltage (Voc) has attracted considerable interest as the large difference between Voc and the bandgap is the main loss mechanism in bulk heterojunction OPVs. Surprisingly, in ternary devices composed of two donors and one acceptor, the Voc is not pinned to the shallowest HOMO but demonstrates a continuous tunability between the binary extremities. We show that this phenomenon can be explained with an equilibrium model where Voc is defined as the splitting of the quasi-Fermi levels of the photo-created holes and electrons in a common density of states accounting for the stoichiometry, i.e. the ratio of the donor materials and the broadening by Gaussian disorder. Evaluating the PCE, it is found that ternary devices do not offer advantages over binary unless the fill factor (FF) is increased at intermediate compositions, as a result of improved transport/recombination upon material blending.Stressing the importance of material intermixing to improve the performance, we found that the presence of an acceptor may drastically alter the mobility and energetic disorder of the donor and vice versa. The effect of different acceptors was studied in a ternary onedonor- two-acceptors system, where the unpredictable variability with composition of the energetic disorder in the HOMO and the LUMO explained the almost linear tunability of Voc. Designing binary OPVs based on the design rule that the energetic disorder can be reduced upon material blending, as we observed, can yield a relative PCE improvement of at least 20%.CT states currently play a key role in evaluating the performance of OPVs and CTelectroluminescence (CT-EL) is assumed to stem from the recombination of thermalized electron-hole pairs. The varying width of the CT-EL peak for different material combinations is intuitively expected to reflect the energetic disorder of the effective HOMO and LUMO. We employ kinetic Monte Carlo (kMC) CT-EL simulations, using independently measured disorder parameters as input, to calculate the ground-to-ground state (0-0) transition spectrum. Including the vibronic broadening according to the Franck Condon principle, we reproduce the width and current dependence of the measured CT-EL peak for a large number of donor-acceptor combinations. The fitted dominant phonon modes compare well with the values measured using the spectral line narrowing technique. Importantly, the calculations show that CT-EL originates from a narrow, non-thermalized subset of all available CT states, which can be understood by considering the kinetic microscopic process with which electron-hole pairs meet and recombine.Despite electron-hole pairs being strongly bound in organic materials, the charge separation process following photo-excitation is found to be extremely efficient and independent of the excitation energy. However, at low photon energies where the charges are excited deep in the tail of the DOS, it is intuitively expected for the extraction yield to be quenched. Internal Quantum Efficiency (IQE) experiments for different material systems show both inefficient and efficient charge dissociation for excitation close to the CT energy. This finding is explained by kinetic Monte Carlo simulations accounting for a varying degree of e-h delocalization, where strongly bound localized CT pairs (< 2nm distance) are doomed to recombine at low excitation energies while extended delocalization over 3-5nm yields an increased and energy-independent IQE. Using a single material parameter set, the experimental CT electroluminescence and absorption spectra are reproduced by the same kMC model by accounting for the vibronic progression of the calculated 0-0 transition. In contrast to CT-EL, CT-absorption probes the complete CT manifold.Charge transport in organic solar cells is currently modelled as either an equilibrium or a non-equilibrium process. The former is described by drift-diffusion (DD) equations, which can be calculated quickly but assume local thermal equilibrium of the charge carriers with the lattice. The latter is described by kMC models, that are time-consuming but treat the charge carriers individually and can probe all relevant time and energy scales. A hybrid model that makes use of the multiple trap and release (MTR) concept in combination with the DD equations is shown to describe both steady-state space charge limited conductivity experiments and non-equilibrium time-resolved transport experiments using a single parameter set. For the investigated simulations, the DD-MTR model is in good agreement with kMC and ~10 times faster.Steady-state mobilities from DD equations have been argued to be exclusively relevant for operating OPVs while charge carrier thermalization and non-equilibrium time-dependent mobilities (although acknowledged) can be disregarded. This conclusion, based on transient photocurrent experiments with μs time resolution, is not complete. We show that non-equilibrium kMC simulations can describe the extraction of charge carriers from subps to 100 μs timescales with a single parameter set. The majority of the fast charge carriers, mostly non-thermalized electrons, are extracted at time scales below the resolution of the experiment. In other words, the experiment resolves only the slower fraction of the charges, predominantly holes.
|
|
| 9. |
- Gabrielsson, Roger
(författare)
-
Electroactive Conjugated Polyelectrolytes Based on EDOT From Synthesis to Organic Electronics
- 2012
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Conjugated polyelectrolytes (CP) show interesting electrical and optical properties for organic electronics as well as for life science applications. Their possibilities of supramolecular assembly with nanowire like misfolded proteins, amyloids, as well as synthetic polypeptides or DNA forming conducting nano composites is highly interesting as being a truly bottom up approach for fabrication of OLEDs, photovoltaic’s as well as logic devices.A special class of CPs is that of electroactive cojugated polymers (ECPs), which, due to their structure, will exhibits a unique combination of properties, including the following; electrically conducting, ability to store an electric charge and ability to exchange ions. The positive or negative excess charge can be introduced into the conjugated polymer by means of chemical or electrochemical oxidation/reduction (a process called doping) following the polymerization reaction. In order to preserve overall electroneutrality of the polymer during introduction of excess charge, ionexhange processes occurs between the polymer phase and the surrounding electrolyte solution. This charge/discharge process can be utilized for application such as; pseudo super capacitors (energy storage through oxidation/reduction processes), electro mechanical actuators (convert electrical energy to mechanical energy) and sensors (converts a chemical signal to electrical conductivity).In this thesis we describes the synthetic challenges with ECPs for applications vide supra. These mostly relates to solubility, ionic functionalization, conductivity and macromolecular properties such as size and shape of the ECPs. The key requirement in the synthesis of ECPs is that the conjugated nature of the monomer is conserved in the synthesis process and that insertion of excess charge (doping) can be obtained. This limits both the choice of monomer and the choice of polymerization process. Monomers of great complexity have been synthesized with this careful goal in mind. Furthermore, the development of novel monomers must also target the appropriate functionality for polymerization. As such, most ECP monomers are electron-rich molecules with pendant groups containing pyrroles, thiophenes, or 3,4-ethylenedioxythiophenes. These three well known ECP monomers are excellent additions to conjugated systems as they typically enable electrochemical polymerization and direct the polymerizations toward linear polymers with good stability towards doping.The first topic of this thesis we demonstrate how we can obtain water soluble ECPs with good electrical conductivity by controlling the polymerization techniques and proper ionic functionalization of the monomer. We also show how these polymers can be incorporated by self-assembly with biomolecular templates, such as, DNA and amyloid fibrils, thus generating novel electrically conductive nanowires.The second topics of this thesis demonstrate how hydrogels of ECPs can be used as bioand charge storage materials, were we demonstrate electronically controlled cell release for biology applications. Both applications are based on ECPs ability to ionexhange processes during electrochemical redox reactions. As well as ions, solvent and other neutral molecules may enter the film during charge/discharge processes. This cause a swelling or shrinking of the ECP films and the expansion and contraction of the polymer network in conjugation with the sorption/desorption of solvent molecules and ions can be described in terms of mechanical work.In the first case we were able to synthesize a water soluble ECP with high amphiphilic character. The polymer was immobilized onto a flexible electrode, suitable for cell growth and subjected to a cell growth media. When the desired cell layer was formed we applied a potential to the flexible electrode. This resulted in that the mechanical work of the immobilized ECP during the applied potential overcame the week adhesive forces to the flexible electrode, which resulted in super swelling and disintegration of the ICP and the cell layer could be harvested.In the second case the possibilities of using synthetically modified ECPs as a dopant during electropolymerization of another ECP monomer to obtain a polymer integrated network with high charge density and good charge transport properties. We demonstrate how this polymer network can be used as porous electrodes suitable for supercapacitors.
|
|
| 10. |
- Gadisa, Abay, 1972-
(författare)
-
Studies of Charge Transport and Energy Level in Solar Cells Based on Polymer/Fullerene Bulk Heterojunction
- 2006
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- π-Conjugated polymers have attracted considerable attention since they are potential candidates for various opto-electronic devices such as solar cells, light emitting iodes, photodiodes, and transistors. Electronic de vices based on conjugated polymers can be easily processed at low temperature using inexpensive technologies. This leads to cost reduction, a key-deriving factor for choosing conjugated polymers for various types of applications. In particular, polymer based solar cells are of special interest due to the fact that they can play a major role in generating clean and cheap energy in the future.The investigations described in thesis are aimed mainly at understanding charge transport and the role of energy le vels in solar cells based on polymer/acceptor bulk heterojunction (BHJ) active films. Best polymer based solar cells, with efficiency 4 to 5%, rely on polymer/fullerene BHJ active films. These solar cells are in an immature state to be used for energy conversion purposes. In order to enhance their performance, it is quite important to understand the efficiency-limiting factors. Solid films of conjugated polymers compose conjugation segments that are randomly distributed in space and energy. Such distributio n gives rise to the localization of charge carriers and hence broadening of electron density of states. Consequently, electronic wave functions have quite poor overlap resulting into absence of continuous band transport. Charge transport in polymers and organic materials, in general, takes place by hopping among the localized states. This makes a bottleneck to the performance of polymer-based solar cells. In this context, the knowledge of charge transport in the solar cell materials is quite important to develop materials and device architectures that boost the efficiency of such solar cells.Most of the transport studies are based on polyfluorene copolymers and fullerene electron acceptor molecules. Fullerenes are blended with polymers to enhance the dissociation of excited state into free carriers and transport free electrons to the respective electrode. The interaction within the polymer-fullerene complex, therefore, plays a major role in the generation and transport of both electrons and holes. In this thesis, we present and discuss the effect of various polymer/fullerene compositions on hole percolation paths. We mainly focus on hole transport since its mobility is quite small as compared to electron mobility in the fullerenes, leading to creation of spa ce charges within the bulk of the solar cell composite. Changing a polymer band gap may necessitate an appropriate acceptor type in order to fulfill the need for sufficient driving force for dissociation of photogenerated electron-hole pairs. We have observed that different acceptor types give rise to completely different hole mobility in BHJ films. The change of hole transport as a function of acceptor type and concentration is mainly attributed to morphological changes. The effect of the acceptors in connection to hole transport is also discussed. The later is supported by studies of bipolar transport in pure electron acceptor layers. Moreover, the link between charge carrier mobility and photovoltaic parameters has also been studied and presented in this thesis.The efficiency of polymer/fullerene-based solar cells is also significantly limited by its open-circuit voltage (Voc), a parameter that does not obey the metal-insulator-metal principle due to its complicated characteristics. In this thesis, we address the effect of varying polymer oxidation potential on Voc of the polymer/fullerene BHJ based solar cells. Systematic investigations have been performed on solar cells that comprise several polythiophene polymers blended with a fullerene derivative electron acceptor molecule. The Voc of such solar cells was found to have a strong correlation with the oxidation potential of the polymers. The upper limit to Voc of the aforementioned solar cells is thermodynamically limited by the net internal electric filed generated by the difference in energy levels of the two materials in the blend.The cost of polymer-based solar cells can be reduced to a great extent through realization of all-plastic and flexible solar cells. This demands the replacement of the metallic components (electrodes) by highly conducting polymer films. While hole conductor polymers are available, low work function polymer electron conductors are rare. In this thesis, prototype solar cells that utilizes a highly conducting polymer, which has a work function of ~ 4.3 eV, as a cathode are demonstrated. Development of this material may eventually lead to fabrication of large area, flexible and cheap solar cells. The transparent nature of the polymer cathode may also facilitate fabrication of multi-layer and tandem solar cells.In the last chapter of this thesis, we demonstrate generation of red and near infrared polarized light by employing thermally converted thin films of polyfluorene copolymers in light emitting diodes. This study, in particular, aims at fabricating polarized infrared light emitting devices.
|
|
