| 1. |
- Andersen, Torben, et al.
(författare)
-
A new concept for large deformable mirrors for extremely large telescopes
- 2006
-
Ingår i: Proceedings of the SPIE - The International Society for Optical Engineering. - : SPIE. - 1996-756X .- 0277-786X. ; 6272:1, s. 324-331
-
Konferensbidrag (refereegranskat)abstract
- For extremely large telescopes, there is strong need for thin deformable mirrors in the 3-4 m class. So far, feasibility of such mirrors has not been demonstrated. Extrapolation from existing techniques suggests that the mirrors could be highly expensive. We give a progress report on a study of an approach for construction of large deformable mirrors with a moderate cost. We have developed low-cost actuators and deflection sensors that can absorb mounting tolerances in the millimeter range, and we have tested prototypes in the laboratory. Studies of control laws for mirrors with thousands of sensors and actuators are in good progress and simulations have been carried out. Manufacturing of thin, glass mirror blanks is being studied and first prototypes have been produced by a slumping technique. Development of polishing procedures for thin mirrors is in progress
|
|
| 2. |
- Andersen, Torben, et al.
(författare)
-
A parallel integrated model of the Euro50
- 2004
-
Ingår i: Proceedings of the SPIE - The International Society for Optical Engineering. - : SPIE. - 0277-786X .- 1996-756X. ; 5497:1, s. 251-265
-
Konferensbidrag (refereegranskat)abstract
- The Euro50 is an astronomical extremely large telescope for optical and infrared wavelength with a 50 m primary mirror. The telescope will have an elaborate control system ("live optics") to correct for atmospheric and telescope aberrations. To study and predict performance of the complete telescope system, an integrated model combining the structural model of the telescope, optics models, the control systems, and the adaptive optics has been established. Wind is taken into account on the basis of wind tunnel measurements and computer fluid dynamics calculations. Atmospheric aberrations are included using a seven-layer atmosphere model. The integrated model is written in Matlab and is run on a cluster computer to achieve acceptable execution times. Dedicated ordinary differential equation solvers have been written and a special toolkit for communication between Matlab processes on different nodes of the cluster computer has been set up. Preliminary results from the complete integrated model, including adaptive optics, are shown
|
|
| 3. |
- Andersen, Torben, et al.
(författare)
-
An Integrated Model of the European Extremely Large Telescope
- 2008
-
Ingår i: MODELLING, SYSTEMS ENGINEERING, AND PROJECT MANAGEMENT FOR ASTRONOMY III. - : SPIE. - 1996-756X .- 0277-786X. ; 7017, s. 216-227
-
Konferensbidrag (refereegranskat)abstract
- Integrated models including optics, structures, control systems, and disturbances are important design tools for Extremely Large Telescopes (ELTs). An integrated model has keen formulated for the European ELT and it includes telescope structure, main servos, primary mirror segment control system, wind, optics, wavefront sensor, deformable mirror, and an AO reconstructor and controller. There are three model phases: Initialization, execution of a solver to determine time responses, and post-processing. In near future, the model will be applied for performance studies and design trade-offs for the European ELT.
|
|
| 4. |
- Andersen, Torben, et al.
(författare)
-
An integrated simulation model of the Euro50
- 2002
-
Ingår i: Proceedings of SPIE - The International Society for Optical Engineering. - : SPIE. - 1996-756X .- 0277-786X. ; 4757, s. 84-92
-
Konferensbidrag (refereegranskat)abstract
- The Euro50 is a proposed optical telescope with an equivalent aperture of 50 m. It will have a segmented primary mirror and full adaptive optics. To study the interaction of the telescope structure, the control system and the optics, an integrated simulation model has been formulated. The mechanical model is a modal version of an Ansys finite element model. The optics model is based on ray tracing and physical optics. The segments model takes the alignment servos and the segment dynamics into account. Wind variation over the primary mirror is included. Segment control system modeling is in progress. First results clearly demonstrate that a good enclosure is needed to protect the telescope well against wind. The results also suggest that the segment alignment system must have a bandwidth well above the lowest eigenfrequencies of the telescope.
|
|
| 5. |
- Andersen, Torben, et al.
(författare)
-
Euro50
- 2003
-
Ingår i: Proceedings of the SPIE - The International Society for Optical Engineering. - : SPIE. - 1996-756X .- 0277-786X. ; 5382:1, s. 169-182
-
Konferensbidrag (refereegranskat)abstract
- The Euro50 is a telescope for optical and infrared wavelengths. It has an aspherical primary mirror with a size of 50 meters and 618 segments. The optical configuration is of Gregorian type and the secondary mirror is deformable for adaptive optics. Observations can take place in prime focus, Gregorian foci, and Nasmyth foci using additional relay mirrors. The telescope provides seeing limited observations, partial adaptive optics with ground layer correction, single conjugate adaptive optics and dual-conjugate adaptive optics. For prime focus observations, a clam-shell corrector with a doublet lens is used. The primary mirror segments can be polished using the precessions polishing technique. "Live Optics" denotes the joint segment alignment system, secondary mirror control system, adaptive optics and main axes servos. An overview is given of the live optics architecture, including feedback from wavefront sensors for natural and laser guide stars, and from primary mirror segment edge sensors. A straw man concept of the laser guide star system using sum-frequency YAG lasers is presented together with a solution to the laser guide star perspective elongation problem. The structural design involves a large steel structure and a tripod of carbon fiber reinforced polymer to support the secondary mirror. Integrated models have been set up to simulate telescope performance. Results show that an enclosure is needed to protect the telescope against wind during observations. The enclosure is very large box-shaped steel structure
|
|
| 6. |
- Andersen, Torben, et al.
(författare)
-
Integrated modeling of the Euro50
- 2003
-
Ingår i: Proceedings of the SPIE - The International Society for Optical Engineering. - : SPIE. - 0277-786X .- 1996-756X. ; 5382:1, s. 366-378
-
Konferensbidrag (refereegranskat)abstract
- The Euro50 is a proposed 50 m optical and infrared telescope. It will have thousands of control loops to keep the optics aligned under influence of wind, gravity and thermal loads. Cross-disciplinary integrated modeling is used to study the overall performance of the Euro50. A sub-model of the mechanical structure originates from finite element modeling. The optical performance is determined using ray tracing, both non-linear and linearized. The primary mirror segment alignment control system is modeled with the 618 segments taken as rigid bodies. Adaptive optics is included using a layered model of the atmosphere and sub-models of the wavefront sensor, reconstructor and controller. The deformable mirror is, so far, described by a simple influence function and a second order dynamical transfer function but more detailed work is in progress. The model has been implemented using Matlab/Simulink on individual computers but it will shortly be implemented on a Beowulf cluster within a trusted network. Communication routines between Matlab on the cluster processors have been written and are being benchmarked. Representative results from the simulations are shown
|
|
| 7. |
- Andersen, Torben, et al.
(författare)
-
Status of the Euro50 project
- 2004
-
Ingår i: Proceedings of the SPIE - The International Society for Optical Engineering. - : SPIE. - 0277-786X .- 1996-756X. ; 5489:1, s. 407-416
-
Konferensbidrag (refereegranskat)abstract
- The Euro50 is an extremely large telescope for optical and infrared wavelength with a 50 m primary mirror. It has a segmented, aspherical primary mirror and an aspherical, deformable secondary in a Gregorian layout. A tentative conceptual design exists and has been documented in a study report. Recent activities have concentrated on the science case for extremely large telescopes in the 50 m class and on identification of potential technical "show stoppers". The science case investigation has identified four fields of particular interest. The studies of critical technical issues have concentrated on atmospheric dispersion effects for high-resolution adaptive optics for extremely large telescopes, and on the influence of wind and other disturbances on wavefront control. Wind load on the telescope, the primary mirror and the enclosure has been studied using wind tunnel measurements and computational fluid dynamics. The impact of wind on the total system has been investigated using an integrated model that includes the telescope structure, the primary mirror segment alignment system, the secondary mirror alignment system, and single conjugate adaptive optics using the deformable secondary mirror. The first, tentative results show that wind disturbances may be significant and that the task of correcting for wind residuals may be at least as large for the adaptive optics system as that of correcting for atmospheric aberrations. The results suggest that use of extremely large telescopes for observations of earth-like planets around nearby stars may imply a considerable challenge
|
|
| 8. |
- Ardeberg, Arne, et al.
(författare)
-
From Euro50 towards a European ELT
- 2006
-
Ingår i: Proceedings of SPIE - The International Society for Optical Engineering. - : SPIE. - 0277-786X .- 1996-756X. ; 6267 II, s. 26725-26725
-
Konferensbidrag (refereegranskat)abstract
- With Euro50 as a convenient telescope laboratory, the Euro50 team has continued development aiming at a European extremely large telescope (ELT). Here, we give a progress report. The needs of science and instrumentation are briefly discussed as is the importance of photometric stability and precision. Results are reported from work on integrated modelling. Details are given concerning point-spread functions (PSFs) obtained with and without adaptive optics (AO). Our results are rather encouraging concerning AO photometry and compensation of edge sensor noise as well as regarding seeing-limited ELT operation. The current status of our development of large deformable mirrors is shown. Low-cost actuators and deflection sensors have been developed as have hierarchic control algorithms. Fabrication of large thin mirror blanks as well as polishing and handling of thin mirrors has been studied experimentally. Regarding adaptive optics, we discuss differential refraction and the limitations imposed by dispersive optical path differences (OPDs) and dispersive anisoplanatism. We report on progress in laser guide star (LGS) performance and a real-time online experiment in multi-conjugate AO (MCAO). We discuss ELTs, high-resolution spectroscopy and pupil slicing with and without use of AO. Finally, we present some recent studies of ELT enclosure options.
|
|
| 9. |
- Darudi, Ahmad, et al.
(författare)
-
The Robotic Earthshine Telescope
- 2010
-
Ingår i: Proceedings of the SPIE. - : SPIE. - 1996-756X .- 0277-786X. ; 7733, s. 8-77332
-
Konferensbidrag (refereegranskat)abstract
- Lund Observatory is presently designing and constructing a robotic telescope dedicated to studies of the Earth's albedo by measuring the ratio between the intensity of the dark and bright sides of the Moon. The telescope will operate both in broadband and narrow-band modes over the entire visible wavelength range and will transmit observational results back to the operation team over the Internet. Design challenges, in particular related to choice of CCD and stray light suppression, are described, together with the design of the optics, control system, and enclosure. Finally we present results from laboratory tests. The telescope will go into operation in the first half of 2011.
|
|
| 10. |
- Enmark, Anita, et al.
(författare)
-
Architecture of the integrated model of the Euro50
- 2006
-
Ingår i: Modeling, Systems Engineering, and Project Management for Astronomy II. - : SPIE. - 0277-786X .- 1996-756X. ; 6271, s. 27114-27114
-
Konferensbidrag (refereegranskat)abstract
- The Euro50 is a proposed 50m extremely large telescope for optical and infrared wavelengths. To study and predict the performance of the complete telescope system, an integrated model combining the structural model of the telescope, optics models, the control systems and the adaptive optics has been established. Wind and atmospheric disturbances are also included in the model. The model is written in MATLAB and C. It is general and modular and built around dedicated ordinary differential equation solvers. The difference in time constants between subsystems is exploited to speed up calculations. The solvers can handle discontinuities and subsystem mode changes. The high degree of modularity allows different telescope designs to be modelled by rearranging subsystem blocks. Certain subsystems, for instance adaptive optics, can also run in a standalone fashion. Parts of the model are parallelized for execution on a large shared memory machine. The resulting architecture of the integrated model and sample results using the code for different telescope models are presented.
|
|
