| 1. |
- Bubnova, Olga, et al.
(författare)
-
Towards polymer-based organic thermoelectric generators
- 2012
-
Ingår i: Energy & Environmental Science. - : Royal Society of Chemistry. - 1754-5692 .- 1754-5706. ; 5:11, s. 9345-9362
-
Tidskriftsartikel (refereegranskat)abstract
- In response to the thread of environmental and ecological degradation along with projected fossil fuel depletion the active search for efficient renewable energy conversion technologies has been attempted in various research areas including the field of thermoelectrics. Despite the availability of considerable amounts of waste and natural heat stored in warm fluids (andlt;250 degrees C) a lack of environmentally friendly materials with high natural abundance, low manufacturing cost and high thermoelectric efficiency impedes the widespread use of thermoelectric generators for energy harvesting on a large scale. In this perspective, we examine the possibility of using organic conducting polymers in thermoelectric applications. We provide an overview of the background and the key concepts of organic thermoelectrics and illustrate some of the first prototypes of polymer-based organic thermoelectric generators.
|
|
| 2. |
- Fan, Qunping, 1989, et al.
(författare)
-
Over 14% efficiency all-polymer solar cells enabled by a low bandgap polymer acceptor with low energy loss and efficient charge separation
- 2020
-
Ingår i: Energy & Environmental Science. - : Royal Society of Chemistry. - 1754-5692 .- 1754-5706. ; 13:12, s. 5017-5027
-
Tidskriftsartikel (refereegranskat)abstract
- Obtaining both high open-circuit voltage (V-oc) and short-circuit current density (J(sc)) has been a major challenge for efficient all-polymer solar cells (all-PSCs). Herein, we developed a polymer acceptor PF5-Y5 with excellent optical absorption capability (onset extending to similar to 880 nm and maximum absorption coefficient exceeding 105 cm(-1) in a film), high electron mobility (3.18 x 10(3) cm(2) V-1 s(-1)) and high LUMO level (-3.84 eV) to address such a challenge. As a result, the PBDB-T:PF5-Y5-based all-PSCs achieved a high power conversion efficiency of up to 14.45% with both a high Voc (0.946 V) and a high Jsc (20.65 mA cm(-2)), due to the high and broad absorption coverage, small energy loss (0.57 eV) and efficient charge separation and transport in the device, which are among the best values in the all-PSC field. In addition, the all-PSC shows a similar to 15% improvement in PCE compared to its counterpart small molecule acceptor (Y5)-based device. Our results suggest that PF5-Y5 is a very promising polymer acceptor candidate for applications in efficient all-PSCs.
|
|
| 3. |
- Felekidis, Nikolaos, et al.
(författare)
-
Open circuit voltage and efficiency in ternary organic photovoltaic blends
- 2016
-
Ingår i: Energy and Environmental Sciences. - : Royal Society of Chemistry (RSC). - 1754-5692 .- 1754-5706. ; 9:1, s. 257-266
-
Tidskriftsartikel (refereegranskat)abstract
- Organic bulk heterojunction solar cells based on ternary blends of two donor absorbers and one acceptor are investigated by experiments and modeling. The commonly observed continuous tunability of the open circuit voltage VOC with the donor1: donor2 ratio can quantitatively be explained as quasi-Fermi level splitting due to photocreated charges filling a joint density of states that is broadened by Gaussian disorder. On this basis, a predictive model for the power conversion efficiency that accounts for the composition-dependent absorption and the shape of the current-voltage characteristic curve is developed. When all other parameters, most notably the fill factor, are constant, we find that for state-of-the-art absorbers, having a broad and strong absorption spectrum, ternary blends offer no advantage over binary ones. For absorbers with a more narrow absorption spectrum ternary blends of donors with complementary absorption spectra, offer modest improvements over binary ones. In contrast, when, upon blending, transport and/or recombination kinetics are improved, leading to an increased fill factor, ternaries may offer significant advantages over binaries.
|
|
| 4. |
- Gao, Feng, et al.
(författare)
-
The renaissance of hybrid solar cells : progresses, challenges, and perspectives
- 2013
-
Ingår i: Energy & Environmental Science. - : Royal Society of Chemistry. - 1754-5692 .- 1754-5706. ; 6:7, s. 2020-2040
-
Forskningsöversikt (refereegranskat)abstract
- Solution-processed hybrid solar cells, a blend of conjugated polymers and semiconducting nanocrystals, are a promising candidate for next-generation energy-conversion devices. The renaissance of this field in recent years has yielded a much deeper understanding of optoelectronic interactions in organic–inorganic hybrid systems. In this article, we review the state-of-the-art progress in hybrid bulk heterojunction solar cells, covering new materials design, interfacial interaction, and processing control. Furthermore, critical challenges that determine photovoltaic performance and prospects for future directions are discussed.
|
|
| 5. |
- Kim, Shi Hyeong, et al.
(författare)
-
Harvesting temperature fluctuations as electrical energy using torsional and tensile polymer muscles
- 2015
-
Ingår i: Energy & Environmental Science. - : Royal Society of Chemistry. - 1754-5692 .- 1754-5706. ; 8, s. 3336-3344
-
Tidskriftsartikel (refereegranskat)abstract
- Diverse means have been deployed for harvesting electrical energy from mechanical actuation produced by low-grade waste heat, but cycle rate, energy-per-cycle, device size and weight, or cost have limited applications. We report the electromagnetic harvesting of thermal energy as electrical energy using thermally powered torsional and tensile artificial muscles made from inexpensive polymer fibers used for fishing line and sewing thread. We show that a coiled 27 μm-diameter nylon muscle fiber can be driven by 16.7 °C air temperature fluctuations to spin a magnetic rotor to a peak torsional rotation speed of 70 000 rpm for over 300 000 heating–cooling cycles without performance degradation. By employing resonant fluctuations in air temperature of 19.6 °C, an average output electrical power of 124 W per kg of muscle was realized. Using tensile actuation of polyethylene-based coiled muscles and alternating flows of hot and cold water, up to 1.4 J of electrical energy was produced per cycle. The corresponding per cycle electric energy and peak power output, per muscle weight, were 77 J kg−1 and 28 W kg−1, respectively.
|
|
| 6. |
- Klug, Matthew T., et al.
(författare)
-
Tailoring metal halide perovskites through metal substitution: influence on photovoltaic and material properties
- 2017
-
Ingår i: Energy & Environmental Science. - : ROYAL SOC CHEMISTRY. - 1754-5692 .- 1754-5706. ; 10:1, s. 236-246
-
Tidskriftsartikel (refereegranskat)abstract
- We present herein an experimental screening study that assesses how partially replacing Pb in methylammonium lead triiodide perovskite films with nine different alternative, divalent metal species, B = {Co, Cu, Fe, Mg, Mn, Ni, Sn, Sr, and Zn}, influences photovoltaic performance and optical properties. Our findings indicate the perovskite film is tolerant to most of the considered homovalent metal species with lead-cobalt compositions yielding the highest power conversion efficiencies when less than 6% of the Pb2+ ions are replaced. Through subsequent materials characterisation, we demonstrate for the first time that partially substituting Pb2+ at the B-sites of the perovskite lattice is not restricted to Group IV elements but is also possible with at least Co2+. Moreover, adjusting the molar ratio of Pb: Co in the mixed-metal perovskite affords new opportunities to tailor the material properties while maintaining stabilised device efficiencies above 16% in optimised solar cells. Specifically, crystallographic analysis reveals that Co2+ incorporates into the perovskite lattice and increasing its concentration can mediate a crystal structure transition from the cubic to tetragonal phase at room-temperature. Likewise, Co2+ substitution continually modifies the perovskite work function and band edge energies without either changing the band gap or electronically doping the intrinsic material. By leveraging this orthogonal dimension of electronic tunability, we achieve remarkably high open-circuit voltages up to 1.08 V with an inverted device architecture by shifting the perovskite into a more favourable energetic alignment with the PEDOT: PSS hole transport material.
|
|
| 7. |
- Kylberg, William, et al.
(författare)
-
Synthesis, thin-film morphology, and comparative study of bulk and bilayer heterojunction organic photovoltaic devices using soluble diketopyrrolopyrrole molecules
- 2011
-
Ingår i: Energy & Environmental Science. - : Royal Society of Chemistry. - 1754-5692 .- 1754-5706. ; 4:9, s. 3617-3624
-
Tidskriftsartikel (refereegranskat)abstract
- Diketopyrrolopyrrole (DPP)-based organic semiconductors EH-DPP-TFP and EH-DPP-TFPV with branched ethyl-hexyl solubilizing alkyl chains and end capped with trifluoromethyl phenyl groups were designed and synthesized via Suzuki coupling. These compounds show intense absorptions up to 700 nm, and thin film-forming characteristics that sensitively depend on the solvent and coating conditions. Both materials have been used as electron donors in bulk heterojunction and bilayer organic photovoltaic (OPV) devices with fullerenes as acceptors and their performance has been studied in detail. The best power conversion efficiency of 3.3% under AM1.5G illumination (100 mW cm(-2)) was achieved for bilayer solar cells when EH-DPP-TFPV was used with C(60), after a thermal annealing step to induce dye aggregation and interdiffusion of C(60) with the donor material. To date, this is one of the highest efficiencies reported for simple bilayer OPV devices.
|
|
| 8. |
- Li, Yaokai, et al.
(författare)
-
Mechanism study on organic ternary photovoltaics with 18.3% certified efficiency: from molecule to device
- 2022
-
Ingår i: Energy & Environmental Science. - : ROYAL SOC CHEMISTRY. - 1754-5692 .- 1754-5706. ; 15:2, s. 855-865
-
Tidskriftsartikel (refereegranskat)abstract
- Multi-component organic photovoltaics (OPVs), e.g., ternary blends, are effective for high performance, while the fundamental understanding from the molecular to device level is lacking. To address this issue, we here systematically study the working mechanism of ternary OPVs based on non-fullerene acceptors (NFAs). With both molecular dynamics simulations and morphology characterization, we identify that when adding another larger band gap and highly miscible NFA, namely IT-4F or BTP-S2, into the PBDB-TF:BTP-eC9 blend, the NFAs undergo molecular intermixing selectively with BTP-eC9. This causes the composition-dependent band gap and charge recombination, and hence the composition-dependent V-OC. While the charge recombination still dominantly occurs at the PBDB-TF:BTP-eC9 interface, BTP-S2 or IT-4F plays an auxiliary role in facilitating charge transfer and suppressing non-radiative decay. Interestingly, intermolecular end-group packing in the intermixed blend is improved compared to that in pristine films, leading to higher carrier mobility. These synergistic effects significantly improve the power conversion efficiency of the device to an outstanding value of 18.7% (certified value of 18.3%).
|
|
| 9. |
- Ma, Zaifei, et al.
(författare)
-
Structure-Property Relationships of Oligothiophene-Isoindigo Polymers for Efficient Bulk-Heterojunction Solar Cells
- 2014
-
Ingår i: energy and environmental science. - : Royal Society of Chemistry. - 1754-5692. ; 17:1, s. 361-369
-
Tidskriftsartikel (refereegranskat)abstract
- A series of alternating oligothiophene (nT)-isoindigo (I) copolymers (PnTI) were synthesized to investigate the influence of the oligothiophene block length on the photovoltaic (PV) properties of PnTI:PCBM bulk-heterojunction blends. Our study indicates that the number of thiophene rings (n) in the repeating unit alters both, polymer crystallinity and polymer-fullerene interfacial energetics, which results in a decreasing open-circuit voltage (Voc) of the solar cells with increasing n. The short-circuit current density (Jsc) of P1TI:PCBM devices is limited by the absence of a significant driving force for electron transfer. Instead, blends based on P5TI and P6TI feature large polymer domains, which limit charge generation and thus Jsc. The best PV performance with a power conversion efficiency of up to 6.9% was achieved with devices based on P3TI, where a combination of favorable morphology and optimal interface energy level offset ensures efficient exciton separation and charge generation. The structure-property relationship demonstrated in this work is a valuable guideline for the design of high performance polymers with small energy losses during the charge generation process, allowing for the fabrication of efficient solar cells that combine a minimal loss in Voc with a high Jsc.
|
|
| 10. |
- Sun, Huiliang, et al.
(författare)
-
A monothiophene unit incorporating both fluoro and ester substitution enabling high-performance donor polymers for non-fullerene solar cells with 16.4% efficiency
- 2019
-
Ingår i: Energy & Environmental Science. - : ROYAL SOC CHEMISTRY. - 1754-5692 .- 1754-5706. ; 12:11, s. 3328-3337
-
Tidskriftsartikel (refereegranskat)abstract
- Thiophene and its derivatives have been extensively used in organic electronics, particularly in the field of polymer solar cells (PSCs). Significant research efforts have been dedicated to modifying thiophene-based units by attaching electron-donating or withdrawing groups to tune the energy levels of conjugated materials. Herein, we report the design and synthesis of a novel thiophene derivative, FE-T, featuring a monothiophene functionalized with both an electron-withdrawing fluorine atom (F) and an ester group (E). The FE-T unit possesses distinctive advantages of both F and E groups, the synergistic effects of which enable significant downshifting of the energy levels and enhanced aggregation/crystallinity of the resulting organic materials. Shown in this work are a series of polymers obtained by incorporating the FE-T unit into a PM6 polymer to fine-tune the energetics and morphology of this high-performance PSC material. The optimal polymer in the series shows a downshifted HOMO and an improved morphology, leading to a high PCE of 16.4% with a small energy loss (0.53 eV) enabled by the reduced non-radiative energy loss (0.23 eV), which are among the best values reported for non-fullerene PSCs to date. This work shows that the FE-T unit is a promising building block to construct donor polymers for high-performance organic photovoltaic cells.
|
|
