| 1. |
- Mahade, Satyapal, 1987-, et al.
(författare)
-
Incorporation of graphene nano platelets in suspension plasma sprayed alumina coatings for improved tribological properties
- 2021
-
Ingår i: Applied Surface Science. - : Elsevier BV. - 0169-4332 .- 1873-5584. ; 570
-
Tidskriftsartikel (refereegranskat)abstract
- Graphene possesses high fracture toughness and excellent lubrication properties, which can be exploited to enhance tribological performance of coating systems utilized to combat wear. In this work, suspension plasma spray (SPS) process was employed to deposit a composite, graphene nano-platelets (GNP) incorporated alumina coating. For comparison, monolithic alumina was also deposited utilizing identical spray conditions. The as-deposited coatings were characterized in detail for their microstructure, porosity content, hardness, fracture toughness and phase composition. Raman analysis of the as-deposited composite coating confirmed retention of GNP. The composite coating also showed good microstructural integrity, comparable porosity, higher fracture toughness and similar alumina phase composition as the monolithic alumina coating. The as-deposited coatings were subjected to dry sliding wear tests. The GNP incorporated composite coating showed lower CoF and lower specific wear rate than the pure alumina coating. Additionally, the counter surface also showed a lower wear rate in case of the composite coating. Post-wear analysis performed by SEM/EDS showed differences in the coating wear track and in the ball wear track of monolithic and composite coatings. Furthermore, Raman analysis in the wear track of composite coating confirmed the presence of GNP. The micro-indentation and wear test results indicate that the presence of GNP in the composite coating aided in improving fracture toughness, lowering CoF and specific wear rate compared to the monolithic coating. Results from this work demonstrated retention of GNP in an SPS processed coating, which can be further exploited to design superior wear-resistant coatings.
|
|
| 2. |
- Alam, M. Minhaj, et al.
(författare)
-
The influence of surface geometry and topography on the fatigue cracking behaviour of laser hybrid welded eccentric fillet joints
- 2010
-
Ingår i: Applied Surface Science. - : Elsevier BV. - 0169-4332 .- 1873-5584. ; 265:6, s. 1936-1945
-
Tidskriftsartikel (refereegranskat)abstract
- Laser hybrid welding of an eccentric fillet joint causes a complex geometry for fatigue load by four point bending. The weld surface geometry and topography were measured and studied in order to understand the crack initiation mechanisms. The crack initiation location and the crack propagation path were studied and compared to Finite Element stress analysis, taking into account the surface macro- and micro-geometry. It can be explained why the root and the upper weld toe are uncritical for cracking. The cracks that initiate from the weld bead show higher fatigue strength than the samples failing at the lower weld toe, as can be explained by a critical radius for the toe below which surface ripples instead determine the main stress raiser location for cracking. The location of maximum surface stress is related to a combination of throat depth, toe radius and sharp surface ripples along which the cracks preferably propagate.
|
|
| 3. |
- Wang, Baochang, 1986-, et al.
(författare)
-
Theoretical and experimental study of the incorporation of tobramycin and strontium-ions into hydroxyapatite by means of co-precipitation
- 2014
-
Ingår i: Applied Surface Science. - : Elsevier BV. - 0169-4332 .- 1873-5584. ; 314, s. 376-383
-
Tidskriftsartikel (refereegranskat)abstract
- Antibiotic incorporation into hydroxyapatite (HA) coatings by co-precipitation and the impact of bone relevant doping elements on the adsorption kinetics are investigated from both theoretical and experimental points of view. Tobramycin interactions with bioactive TiO2 and HA surfaces are analyzed using density functional theory. According to the calculations, the drug molecule has larger adsorption energy than the Ca+ ion on both surfaces under study in Phosphate Buffered Saline (PBS). The results support the experimental observations that HA nucleation and growth are strongly limited on TiO2 surfaces in the presence of clinically relevant antibiotic concentrations in PBS. The drug molecule is more likely to adopt parallel arrangement onto the HA surface, as the adsorption energy of such arrangement is higher compared to a perpendicular one. Strontium substitution of the HA surface is found to results in a weaker drug-surface interaction, and leads also to a decrease in coating thickness. However, the presence of strontium gives rise to a coating morphology with enhanced drug incorporation capacity and slower antibiotic release compared to non-substituted, co-precipitated counterparts. Our theoretical calculation results were found to be in excellent agreement with experimental data and provide a powerful tool to understand the interaction mechanism between drug and different surface chemistries necessary for development of future versatile orthopedic and dental implant surfaces.
|
|
| 4. |
- Lindahl, Carl, et al.
(författare)
-
Biomimetic calcium phosphate coating of additively manufactured porous CoCr implants
- 2015
-
Ingår i: Applied Surface Science. - : Elsevier BV. - 0169-4332 .- 1873-5584. ; 353, s. 40-47
-
Tidskriftsartikel (refereegranskat)abstract
- The aim of this work was to study the feasibility to use a biomimetic method to prepare biomimetic hydroxyapatite (HA) coatings on CoCr substrates with short soaking times and to characterize the properties of such coatings. A second objective was to investigate if the coatings could be applied to porous CoCr implants manufactured by electron beam melting (EBM). The coating was prepared by immersing the pretreated CoCr substrates and EBM implants into the phosphate-buffered solution with Ca2+ in sealed plastic bottles, kept at 60 degrees C for 3 days. The formed coating was partially crystalline, slightly calcium deficient and composed of plate-like crystallites forming roundish flowers in the size range of 300-500 nm. Cross-section imaging showed a thickness of 300-500 nm. In addition, dissolution tests in Tris-HCl up to 28 days showed that a substantial amount of the coating had dissolved, however, undergoing only minor morphological changes. A uniform coating was formed within the porous network of the additive manufactured implants having similar thickness and morphology as for the flat samples. In conclusion, the present coating procedure allows coatings to be formed on CoCr and could be used for complex shaped, porous implants made by additive manufacturing.
|
|
| 5. |
- Bergström, David, et al.
(författare)
-
The absorptance of steels to Nd:YLF and Nd:YAG laser light at room temperature
- 2007
-
Ingår i: Applied Surface Science. - : Elsevier BV. - 0169-4332 .- 1873-5584. ; 253:11, s. 5017-5028
-
Tidskriftsartikel (refereegranskat)abstract
- The measurement of absorptance is important for the analysis and modelling of laser-material interactions. Unfortunately, most of the absorptance data presently available considers only polished pure metals rather than the commercially available (unpolished, oxidised) alloys, which are actually being processed in manufacturing. This paper presents the results of absorptance measurements carried out at room temperature on as-received engineering grade steels including hot and cold rolled mild steel and stainless steels of various types. The measurements were made using an integrating sphere with an Nd:YLF laser at two wavelengths (1053 and 527 nm, which means that the results are also valid for Nd:YAG radiation at 1064 and 532 nm). The absorptance results obtained differ considerably from existing data for polished, pure metals and should help improve the accuracy of laser-material interaction models. Some clear trends were identified; for all materials studied, the absorptance was considerably higher than the previously published values for the relevant pure metals with polished surfaces. For all 15 samples the absorptance was higher for the green than for the infrared wavelength. No clear trend correlating the absorptance with the roughness was found for mild steel in the roughness range Sa 0.4-5.6 μm. A correlation between absorptance and roughness was noted for stainless steel for Sa values above 1.5 μm.
|
|
| 6. |
- Rogström, Lina, 1983-, et al.
(författare)
-
Structural changes in Ti1-xAlxN coatings during turning : A XANES and EXAFS study of worn tools
- 2023
-
Ingår i: Applied Surface Science. - : Elsevier. - 0169-4332 .- 1873-5584. ; 612
-
Tidskriftsartikel (refereegranskat)abstract
- Structural changes in Ti1-xAlxN coated tool inserts used for turning in 316L stainless steel were investigated by XANES, EXAFS, EDS, and STEM. For coarse-grained fcc-structured Ti1-xAlxN coatings, with 0 ≤ x ≤ 0.62, the XANES spectrum changes with Al-content. XANES Ti 1s line-scans across the rake face of the worn samples reveals that TiN-enriched domains have formed during turning in Ti0.47Al0.53N and Ti0.38Al0.62N samples as a result of spinodal decomposition. The XANES spectra reveal the locations on the tool in which the most TiN-rich domains have formed, indicating which part of the tool-chip contact area that experienced the highest temperature during turning. Changes in the pre-edge features in the XANES spectra reveal that structural changes occur also in the w-TiAlN phase in fine-grained Ti0.38Al0.62N during turning. EDS shows that Cr and Fe from the steel adhere to the tool rake face during machining. Cr 1s and Fe 1s XANES show that Cr is oxidized in the end of the contact length while the adhered Fe retains in the same fcc-structure as that of the 316L stainless steel.
|
|
| 7. |
- Tuominen, Mikko, et al.
(författare)
-
Superamphiphobic overhang structured coating on a biobased material
- 2016
-
Ingår i: Applied Surface Science. - : Elsevier. - 0169-4332 .- 1873-5584. ; 389, s. 135-143
-
Tidskriftsartikel (refereegranskat)abstract
- A superamphiphobic coating on a biobased material shows extreme liquid repellency with static contact angles (CA) greater than 150 degrees and roll-off angles less than 10 degrees against water, ethylene glycol, diiodomethane and olive oil, and a CA for hexadecane greater than 130 degrees. The coating consisting of titanic nanoparticles deposited by liquid flame spray (LFS) and hydrophobized using plasma-polymerized perfluorohexane was applied to a birch hardwood. Scanning electron microscopy (SEM) imaging after sample preparation by UV laser ablation of coated areas revealed that capped structures were formed and this, together with the geometrically homogeneous wood structure, fulfilled the criteria for overhang structures to occur. The coating showed high hydrophobic durability by still being non-wetted after 500 000 water drop impacts, and this is discussed in relation to geometrical factors and wetting forces. The coating was semi-transparent with no significant coloration. A self-cleaning effect was demonstrated with both water and oil droplets. A self-cleanable, durable and highly transparent superamphiphobic coating based on a capped overhang structure has a great potential for commercial feasibility in a variety of applications, here exemplified for a biobased material.
|
|
| 8. |
- Amer, Eynas, et al.
(författare)
-
Comparison of the laser ablation process on Zn and Ti using pulsed digital holographic interferometry
- 2010
-
Ingår i: Applied Surface Science. - : Elsevier BV. - 0169-4332 .- 1873-5584. ; 256:14, s. 4633-4641
-
Tidskriftsartikel (refereegranskat)abstract
- Pulsed digital holographic interferometry has been used to compare the laser ablation process of a Q-switched Nd-YAG laser pulse (wavelength 1064 nm, pulse duration 12 ns) on two different metals (Zn and Ti) under atmospheric air pressure. Digital holograms were recorded for different time delays using collimated laser light (532 nm) passed through the volume along the target. Numerical data of the integrated refractive index field were calculated and presented as phase maps. Intensity maps were calculated from the recorded digital holograms and are used to calculate the attenuation of the probing laser beam by the ablated plume. The different structures of the plume, namely streaks normal to the surface for Zn in contrast to absorbing regions for Ti, indicates that different mechanisms of laser ablation could happen for different metals for the same laser settings and surrounding gas. At a laser fluence of 5 J/cm2, phase explosion appears to be the ablation mechanism in case of Zn, while for Ti normal vaporisation seems to be the dominant mechanism.
|
|
| 9. |
- Amer, Eynas, et al.
(författare)
-
Impact of an extended source in laser ablation using pulsed digital holographic interferometry and modelling
- 2009
-
Ingår i: Applied Surface Science. - : Elsevier BV. - 0169-4332 .- 1873-5584. ; 255:21, s. 8917-8925
-
Tidskriftsartikel (refereegranskat)abstract
- Pulsed digital holographic interferometry has been used to study the effect of the laser spot diameter on the shock wave generated in the ablation process of an Nd:YAG laser pulse on a Zn target under atmospheric pressure. For different laser spot diameters and time delays, the propagation of the expanding vapour and of the shock wave were recorded by intensity maps calculated using the recorded digital holograms. From the latter phase maps, the refractive index and the density field can be derived. A model was developed that approaches the density distribution, in particular the ellipsoidal expansion characteristics. The induced shock wave has an ellipsoid shape that approaches a sphere for decreasing spot diameter. The ellipsoidal shock waves have almost the same centre offset towards the laser beam and the same aspect ratio for different time steps. The model facilitates the derivation of the particle velocity field. The method provides valuable quantitative results that are discussed, in particular in comparison with the simpler point source explosion theory.
|
|
| 10. |
- Dehestani, Mahdi, et al.
(författare)
-
Improving bioactivity of inert bioceramics by a novel Mg-incorporated solution treatment
- 2017
-
Ingår i: Applied Surface Science. - : Elsevier B.V.. - 0169-4332 .- 1873-5584. ; 425, s. 564-575
-
Tidskriftsartikel (refereegranskat)abstract
- Zirconia/alumina ceramics possess outstanding mechanical properties for dental and orthopedic applications, but due to their poor surface bioactivities they exhibit a weak bone-bonding ability. This work proposes an effective 30-min solution treatment which could successfully induce formation of bone-like apatite on the surface of 3Y-TZP and a ternary composite composed of yttria-stabilized zirconia, ceria-stabilized zirconia, and alumina (35 vol% 3Y-TZP + 35 vol% 12Ce-TZP + 30 vol% Al2O3) after 3 weeks immersion in simulated body fluid (SBF). XRD was used for phase identification in the ceramic materials. The influence of solution treatment on the surface chemistry and its role on apatite formation were investigated via SEM, EDS and XPS. In vitro apatite-forming ability for the solution-treated and untreated samples of the composite and individual substrates of 3Y-TZP, 12Ce-TZP, and Al2O3 was evaluated by immersion in SBF. Apatite crystals were formed only on 3Y-TZP and composite substrates, implying that it is mainly the 3Y-TZP constituent that contributes to the bioactivity of the composite. Further, it was found from the XPS analysis that the zirconia material with higher phase stability (12Ce-TZP) produced less Zr–OH functional groups on its surface after solution treatment which accounts for its weaker bioactivity compared to 3Y-TZP.
|
|
