| 1. |
- Alkadir Abdulahi, Birhan, 1985, et al.
(författare)
-
Structural engineering of pyrrolo[3,4-: F] benzotriazole-5,7(2 H,6 H)-dione-based polymers for non-fullerene organic solar cells with an efficiency over 12%
- 2019
-
Ingår i: Journal of Materials Chemistry A. - : Royal Society of Chemistry (RSC). - 2050-7488 .- 2050-7496. ; 7:33, s. 19522-19530
-
Tidskriftsartikel (refereegranskat)abstract
- In this work, we have synthesized two wide band gap donor polymers based on benzo[1,2-b:4,5-b′]dithiophene (BDT) and pyrrolo[3,4-f]benzotriazole-5,7(2H,6H)-dione (TzBI), namely, PBDT-TzBI and PBDT-F-TzBI and studied their photovoltaic properties by blending them with ITIC as an acceptor. Polymer solar cell devices made from PBDT-TzBI:ITIC and PBDT-F-TzBI:ITIC exhibited power conversion efficiencies (PCEs) of 9.22% and 11.02% and while annealing at 160 °C, improved the device performances to 10.24% and 11.98%, respectively. Upon solvent annealing with diphenyl ether (DPE) (0.5%) and chlorobenzene (CB), the PCE of the PBDT-F-TzBI-based device increased to 12.12%. The introduction of the fluorinated benzodithiophene (BDT-F) moiety on the backbone of PBDT-F-TzBI improved the open circuit voltage, short circuit current and fill factor simultaneously. The high PCEs of the PBDT-F-TzBI:ITIC-based devices were supported by comparison and analysis of the optical and electronic properties, the charge carrier mobilities, exciton dissociation probabilities, and charge recombination behaviors of the devices.
|
|
| 2. |
- Barzgar Vishlaghi, Mahsa, et al.
(författare)
-
Accelerating water oxidation on BiVO 4 photoanodes via surface modification with Co dopants
- 2023
-
Ingår i: Journal of Materials Chemistry A. - 2050-7488 .- 2050-7496. ; 11:31, s. 16648-16658
-
Tidskriftsartikel (refereegranskat)abstract
- Despite the vast investigations on improving the photoelectrochemical performance of BiVO4 for water splitting, charge recombination in the near-surface region remains a challenge. In this study, we showed that the diffusion of Co2+ ions into the BiVO4 subsurface boosted the water oxidation activity and charge injection efficiency remarkably. The increase in the concentration of oxygen vacancies upon the incorporation of cobalt ions was shown by electron paramagnetic resonance (EPR) spectroscopy and confirmed by density functional theory (DFT) calculations. DFT calculations revealed that vanadium sites in the subsurface region were the most favorable sites for substitution with cobalt ions. Charge localization at surface oxygen vacancies was found less favorable in the presence of cobalt in the subsurface layer, eliminating surface recombination. This resulted in 4.25 times larger charge injection efficiency and 6.2 times higher photocurrent density at the potential of ∼0.6 V, as compared to pristine BiVO4. This enhancement was significantly larger as compared to CoOx-loaded BiVO4, indicating that the suppressed recombination at the surface and improved charge transfer kinetics obtained solely by CoOx deposition are not sufficient for enhanced activity of BiVO4. A longer charge carrier lifetime obtained upon cobalt incorporation was observed by transient absorption spectroscopy and verified the reduced rate of recombination.
|
|
| 3. |
- Bergqvist, J., et al.
(författare)
-
Sub-glass transition annealing enhances polymer solar cell performance
- 2014
-
Ingår i: Journal of Materials Chemistry A. - 2050-7488 .- 2050-7496. ; 2:17, s. 6146-6152
-
Tidskriftsartikel (refereegranskat)abstract
- Thermal annealing of non-crystalline polymer:fullerene blends typically results in a drastic decrease in solar cell performance. In particular aggressive annealing above the glass transition temperature results in a detrimental coarsening of the blend nanostructure. We demonstrate that mild annealing below the glass transition temperature is a viable avenue to control the nanostructure of a non-crystalline thiophene–quinoxaline copolymer:fullerene blend. Direct imaging methods indicate that coarsening of the blend nanostructure can be avoided. However, a combination of absorption and luminescence spectroscopy reveals that local changes in the polymer conformation as well as limited fullerene aggregation are permitted to occur. As a result, we are able to optimise the solar cell performance evenly across different positions of the coated area, which is a necessary criterion for large-scale, high throughput production.
|
|
| 4. |
- Bharmoria, Pankaj, 1985, et al.
(författare)
-
Recyclable optical bioplastics platform for solid state red light harvesting via triplet-triplet annihilation photon upconversion
- 2022
-
Ingår i: Journal of Materials Chemistry A. - : Royal Society of Chemistry (RSC). - 2050-7496 .- 2050-7488. ; 10:40, s. 21279-21290
-
Tidskriftsartikel (refereegranskat)abstract
- Sustainable photonics applications of solid-state triplet-triplet annihilation photon upconversion (TTA-UC) are limited by a small UC spectral window, low UC efficiency in air, and non-recyclability of polymeric materials used. In a step to overcome these issues, we have developed new recyclable TTA-UC bioplastics by encapsulating TTA-UC chromophores liquid inside the semicrystalline gelatin films showing broad-spectrum upconversion (red/far-red to blue) with high UC efficiency in air. For this, we synthesized a new anionic annihilator, sodium-TIPS-anthracene-2-sulfonate (TIPS-AnS), that combined with red/far-red sensitizers (PdTPBP/Os(m-peptpy)(2)(TFSI)(2)), a liquid surfactant Triton X-100 reduced (TXr) and protein gelatin (G) formed red/far-red to blue TTA-UC bioplastic films just by air drying of their aqueous solutions. The G-TXr-TIPS-AnS-PdTPBP film showed record red to blue (633 to 478 nm) TTA-UC quantum yield of 8.5% in air. The high UC quantum yield has been obtained due to the fluidity of dispersed TXr containing chromophores and oxygen blockage by gelatin fibers that allowed efficient diffusion of triplet excited chromophores. Further, the G-TXr-TIPS-AnS-Os(m-peptpy)(2)(TFSI)(2) bioplastic film displayed far-red to blue (700-730 nm to 478 nm) TTA-UC, demonstrating broad-spectrum photon harvesting. Finally, we demonstrated the recycling of G-TXr-TIPS-AnS-PdTPBP bioplastics by developing a downstream approach that gives new directions for designing future recyclable photonics bioplastic materials.
|
|
| 5. |
- Bielecki, Johan, 1982, et al.
(författare)
-
Short-range structure of the brownmillerite-type oxide Ba2In2O5 and its hydrated proton-conducting form BaInO3H
- 2014
-
Ingår i: Journal of Materials Chemistry A. - : Royal Society of Chemistry (RSC). - 2050-7488 .- 2050-7496. ; 2:40, s. 16915-16924
-
Tidskriftsartikel (refereegranskat)abstract
- The vibrational spectra and short-range structure of the brownmillerite-type oxide Ba2In2O6 and its hydrated form BaInO3H, are investigated by means of Raman, infrared, and inelastic neutron scattering spectroscopies together with density functional theory calculations. For Ba2In2O6, which may be described as an oxygen deficient perovskite structure with alternating layers of InO6 octahedra and InO4 tetrahedra, the results affirm a short-range structure of Icmm symmetry, which is characterized by random orientation of successive layers of InO4 tetrahedra. For the hydrated, proton conducting, form, BaInO3H, the results suggest that the short-range structure is more complicated than the P4/mbm symmetry that has been proposed previously on the basis of neutron diffraction, but rather suggest a proton configuration close to the lowest energy structure predicted by Martinez et al. [J.-R. Martinez, C. E. Moen, S. Stoelen, N. L. Allan, J. Solid State Chem., 180, 3388, (2007)]. An intense Raman active vibration at 150 cm(-1) is identified as a unique fingerprint of this proton configuration.
|
|
| 6. |
- Bielecki, Johan, et al.
(författare)
-
Structure and dehydration mechanism of the proton conducting oxide Ba2In2O5(H2O)(x)
- 2016
-
Ingår i: Journal of Materials Chemistry A. - : Royal Society of Chemistry (RSC). - 2050-7488 .- 2050-7496. ; 4:4, s. 1224-1232
-
Tidskriftsartikel (refereegranskat)abstract
- The structure and dehydration mechanism of the proton conducting oxide Ba2In2O5(H2O)(x) are investigated by means of variable temperature (20-600 degrees C) Raman spectroscopy together with thermal gravimetric analysis and inelastic neutron scattering. At room temperature, Ba2In2O5(H2O)(x) is found to be fully hydrated (x = 1) and to have a perovskite-like structure, which dehydrates gradually with increasing temperature and at around 600 degrees C the material is essentially dehydrated (x approximate to 0.2). The dehydrated material exhibits a brownmillerite structure, which is featured by alternating layers of InO6 octahedra and InO4 tetrahedra. The transition from a perovskite-like to a brownmillerite-like structure upon increasing temperature occurs through the formation of an intermediate phase at ca. 370 degrees C, corresponding to a hydration degree of approximately 50%. The structure of the intermediate phase is similar to the structure of the dehydrated material, but with the difference that it exhibits a non-centrosymmetric distortion of the InO6 octahedra that is not present in the dehydrated material. The dehydration process upon heating is a two-stage mechanism; for temperatures below the hydrated-to-intermediate phase transition, dehydration is characterized by a homogenous release of protons over the entire oxide lattice, whereas above the transition a preferential desorption of protons originating in the nominally tetrahedral layers is observed. Furthermore, our spectroscopic results point towards the co-existence of two structural phases, which relate to the two lowest-energy proton configurations in the material. The relative contributions of the two proton configurations depend on how the sample is hydrated.
|
|
| 7. |
- Cattaruzza, Martina, et al.
(författare)
-
Hybrid polymer-liquid lithium ion electrolytes: effect of porosity on the ionic and molecular mobility
- 2023
-
Ingår i: Journal of Materials Chemistry A. - : Royal Society of Chemistry (RSC). - 2050-7488 .- 2050-7496. ; 11:13, s. 7006-7015
-
Tidskriftsartikel (refereegranskat)abstract
- Alternative electrolyte systems such as hybrid electrolytes are much sought after to overcome safety issues related to liquid electrolytes in lithium ion batteries (LIBs). Hybrid solid-liquid electrolytes (HEs) like the heterogeneous structural battery electrolyte (SBE) consist of two discrete co-existing phases prepared by polymerization-induced phase separation: one solid polymer phase providing mechanical integrity and the other one a percolating liquid ion-conducting phase. The present work investigates the ion and the solvent mobility in a series of HEs using morphological, electrochemical impedance and NMR spectroscopic methods. All the dried HEs exhibit a porous structure with a broad pore size distribution stretching down to <10 nm diameter. Penetration of the individual components of the solution, that is the ions and the solvent, in the solid polymer phase is demonstrated. Yet, it is the pores that are the main ion conduction channels in the liquid-saturated HEs and, in general, translational mobility is strongly dependent on the volume fraction and size of the pores and, thereby, on the initial liquid electrolyte content. We also observe that the translational mobility of solvent and the ions vary differently with the pore volume fraction. This finding is explained by the presence of small mesopores where the mobility strongly depends on the specific interactions of the molecular constituent with the pore wall. These interactions are inferred to be stronger for the EC/PC solvent than for the ions. This study shows how the morphology and the chemical composition of HEs affect the ionic and molecular transport in the system.
|
|
| 8. |
- Chen, Haiwei, et al.
(författare)
-
Extending the environmental lifetime of unpackaged perovskite solar cells through interfacial design
- 2016
-
Ingår i: Journal of Materials Chemistry A. - : Royal Society of Chemistry (RSC). - 2050-7488 .- 2050-7496. ; 4:30, s. 11604-11610
-
Tidskriftsartikel (refereegranskat)abstract
- Solution-processed oxo-functionalized graphene (oxo-G1) is employed to substitute hydrophilic PEDOT:PSS as an anode interfacial layer for perovskite solar cells. The resulting devices exhibit a reasonably high power conversion efficiency (PCE) of 15.2% in the planar inverted architecture with oxo-G1 as a hole transporting material (HTM), and most importantly, deploy the full open-circuit voltage (Voc) of up to 1.1 V. Moreover, oxo-G1 effectively slows down the ingress of water vapor into the device stack resulting in significantly enhanced environmental stability of unpackaged cells under illumination with 80% of the initial PCE being reached after 500 h. Without encapsulation, ∼60% of the initial PCE is retained after ∼1000 h of light soaking under 0.5 sun and ambient conditions maintaining the temperature beneath 30 °C. Moreover, the unsealed perovskite device retains 92% of its initial PCE after about 1900 h under ambient conditions and in the dark. Our results underpin that controlling water diffusion into perovskite cells through advanced interface engineering is a crucial step towards prolonged environmental stability.
|
|
| 9. |
- Chen, Pan, et al.
(författare)
-
Surface modification effects on nanocellulose - molecular dynamics simulations using umbrella sampling and computational alchemy
- 2020
-
Ingår i: Journal of Materials Chemistry A. - : Royal Society of Chemistry (RSC). - 2050-7496 .- 2050-7488. ; 8:44, s. 23617-23627
-
Tidskriftsartikel (refereegranskat)abstract
- Topochemical modification of nanocellulose particles, in particular acetylation, is commonly used to reduce hygroscopicity and improve their dispersibility in non-polar polymers. Despite enormous experimental efforts on cellulose surface modification, there is currently no comprehensive model which considers both (a) the specific interactions between nanocellulose particles and the surrounding liquid or polymer matrix, and (b) the interactions between the particles themselves. The second mechanism is therefore frequently ignored. The present approach is based on atomistic molecular dynamics (MD) simulations, where computational alchemy is used to calculate the changes in interactions between nanocellulose and the surrounding medium (liquid or polymer) upon modification. This is combined with another method, based on potential of mean force, to calculate interactions between particles. Results show that both contributions are of equal importance for nanoparticle surface acetylation effects. The proposed method is not restricted to either cellulose or acetylation, and has the prospect to find application in a broad context of nanomaterials design.
|
|
| 10. |
- Coduri, Mauro, et al.
(författare)
-
Structure-property correlation in oxide-ion and proton conductors for clean energy applications: recent experimental and computational advancements
- 2022
-
Ingår i: Journal of Materials Chemistry A. - : Royal Society of Chemistry (RSC). - 2050-7496 .- 2050-7488. ; 10, s. 5082-5110
-
Forskningsöversikt (refereegranskat)abstract
- In the last decade, the field of oxide-ion and proton conductors continued to trigger a significant amount of basic research aimed at improving the properties and the comprehension of actual materials, as well as at discovering novel phases. This need comes from the current and future urgent requests of changing our energy management towards cleaner solutions such as solid oxide fuel cells. In this review article, we highlight the most recent advancements in this exciting field by putting particular emphasis on the structure-property correlations in oxide-ion and proton conductors both from an experimental and a computational perspective. Special focus is laid on developments in the area of operando and in situ spectroscopy, machine learning and high-throughput approaches to accelerate the discovery of new and advanced materials.
|
|
