| 1. |
- Anderberg, Cecilia, et al.
(författare)
-
Combined SEM and Stylus Profiling Sensoring for Improved Cylinder Liner Honing
- 2006
-
Ingår i: Proceedings of Austrib 06 - International Tribology Conference. - Brisbane : Queensland University of Technology. ; , s. 6-
-
Konferensbidrag (refereegranskat)abstract
- The demands on decreased environmental impact from vehicles are resulting in a strong push for decreased engine oil and fuel consumption.Recent engine tests have shown a promising reduction in oil consumption when using cylinder liners with a smoother finish than the current plateau honing.One approach to produce smoother liner surfaces is to replace SiC ceramic honing stones with diamond tools. However, even though the diamond honing process results in higher productivity, improved quality control is needed to monitor the degree of cold worked material - “blechmantel” (German), and the resulting risk of increased wear and scuffing.A number of petrol and diesel engine cylinder liners have been mapped to be able to verify the quality and consequences, in terms of wear and function, of the honing process. A new mapping method, combining SEM images and quantitative image analysis with traditional 2D profilometry has been developed and tested in this study. The surface mapping method developed was employed before and after the test to study effect of running-in wear on the surface, features characterized with the SEM- and the 2D profilometer.The results show that combining SEM- and profilometric methods gives a good picture of the effects of varying the cylinder liner pressure and roughness. The core roughness decreases more for diesel liners than for petrol liners.. A probable cause is that the more severe diesel high pressure run-in conditions are able to effectively “truncate” the plateaux and remove residing plastically deformed un-cut honing residues while the less severe petrol liner conditions do not manage to remove the blechmantel and irregularities to an important extent.
|
|
| 2. |
- Anderberg, Cecilia, et al.
(författare)
-
Cylinder Liners and Consequences of Improved Honing
- 2006
-
Ingår i: Proceedings of Nordtrib conference 2006, Helsingor, Danemark. ; , s. 13-
-
Konferensbidrag (refereegranskat)abstract
- The demands on decreased environmental impact from vehicles are resulting in a strong push for decreased engine oil and fuel consumption. Engine oil and fuel consumption are to a great extent controlled by the topography of the cylinder liner surface.Recent engine tests have shown a promising reduction in oil consumption when using cylinder liners with a smoother finish than the current plateau honing.One approach to produce smoother liner surfaces is to replace SiC ceramic honing stones with diamond tools. However, event though the diamond honing process results in higher productivity, improved demands of quality control is needed to monitor the degree of cold worked material - “blechmantel” (German), and the resulting risk of increased wear and scuffing.A number of petrol and diesel engine cylinder liners have been mapped to be able to verify the quality and consequences, in terms of wear and function, of the honing process. A new mapping method, combining SEM images and quantitative image analysis with traditional 2D profilometry has been developed and tested in this study. The liners where tested in a reciprocating rig of 8 mm stroke and with a frequency of 10 Hz, simulating the top-dead center conditions in a running engine.The tests where carried out in high- and low pressure conditions with smooth respectively rough liner roughnesses against PVD coated piston rings. The developed surface mapping method was employed before and after the test to study effect of running-in wear on the surface, features characterized with the SEM- and the 2D profilometer.The results show that combining SEM- and profilometric methods gives a good picture of the effects of varying the cylinder liner pressure and roughness. The core roughness decrease more for diesel liners than for petrol liners. In average (rough and smooth liners) the diesel core roughness decrease 265% while the petrol liners average on a 60% decrease. Blechmantel- and Irregularities ratio show a high sensitivity to varying conditions and decrease 1180% to 100% for the diesel liners while the parameters increase between 106% to 18% for all the petrol liners. A probable cause is the more severe diesel high pressure run-in conditions are able to effectively “truncate” the plateaux and remove residing plastically deformed un-cut honing residues while the less severe petrol liner conditions not manage to remove the blechmantel and irregularities in an important extent.
|
|
| 3. |
- Anderberg, Cecilia, et al.
(författare)
-
Wear Resistance of Smooth Automotive Cylinder Liner Surfaces
- 2005
-
Ingår i: World Tribology Congress III, Volume 2. - New York, NY : ASME Press. - 0791842029 ; , s. 603-604
-
Konferensbidrag (refereegranskat)abstract
- Demands for decreased environmental impact from vehicles are resulting in a strong push for decreased engine oil, fuel consumption and weight. New machining and coating technologies have offered ways to attack these problems. Engine oil and fuel consumption are to a great extent controlled by the topography of the cylinder liner surface and it is therefore important to optimise this surface. Recent engine tests have shown a reduction in oil consumption when using cylinder liners with a smoother finish than that given by the current plateau honing. However, engine manufacturers are hesitant to introduce smoother liner surfaces because of fears of severe wear and scuffing. There is also the possibility that smoother liner surfaces may be more sensitive to the choice of piston ring finishes. This paper therefore seeks to investigate the functional performance and resistance to wear of these smooth cylinder liners and the mating top ring surfaces. Copyright © 2005 by ASME
|
|
| 4. |
|
|
| 5. |
- Dimkovski, Zlate, et al.
(författare)
-
Characterisation of Worn Cylinder Liner Surfaces by Segmentation of Honing and Wear Scratches
- 2009
-
Ingår i: Proceedings of the 12th International Conference on Metrology and Properties of Engineering Surfaces. - Rzesow, Poland : Rzeszow University of Technology. - 9788371995453 ; , s. 187-192
-
Konferensbidrag (refereegranskat)abstract
- The presence of the honing scratches/grooves in cylinder liner surfaces is intended and desired as they improve the lubrication and retain the debris reducing the piston assembly/liner friction and consequently improve the fuel economy and longevity of the internal combustion (IC) engines. Axial scratches caused by the abrasive wear between the tribological partners and/or entrained wear particles are undesired since they are correlated with increased oil consumption and noxious emissions of the IC engines. Due to the imperfection of the manufacturing process, the honing grooves, especially the deep ones, are smeared and interrupted by folds. A portion of the folds would eventually detach during the running process and act as abrasive particles increasing the wear in the cylinder. To closely examine the influence of all these features on the liner's function, it emerges a need to objectively quantify the axial wear scratches, plateau honing grooves, deep honing grooves and their interrupts. The existing techniques fail to segment a groove containing interrupts as they usually appear as summits at several locations in the course of the groove. Combining the profile and image analyses, the deep grooves and their interrupts were successfully identified and quantified in earlier works of the authors. In this paper those algorithms are extended, so that the deep honing grooves, plateau honing grooves and axial scratches crossing different depth levels are sequentially segmented in three levels/steps in an immersing way. A number of parameters derived from this method were utilised to compare 3D interference measurements from the top dead centre, middle and bottom region of a liner run in a truck engine test whereas the three regions represent different wear regimes due to the different running conditions. The results show that: (i) the axial scratches are densest in the top dead centre and about the same size as the plateau grooves in all three regions, while in the bottom region there are only few scratches; (ii) the presence of plateau grooves in the top region clearly decreases, (iii) the deep groove interrupt and coverage are lowest in the top region, and (iv) the groove height and distance between grooves spread mostly. © 2010 Elsevier B.V. All rights reserved.
|
|
| 6. |
- Dimkovski, Zlate, et al.
(författare)
-
Complementing 3D Roughness Parameters for Monitoring of Improved Honing of Cylinder Bores
- 2008
-
Ingår i: Proceedings of the Swedish Production Symposium (SPS) - 2008. - 9783939026952
-
Konferensbidrag (refereegranskat)abstract
- It is of common interest to reduce the oil consumption and frictional losses in the internal combustion engines which are in a great deal influenced by the quality of the cylinder liner surface. Its criss-cross patterned topography consists of a communicating system of grooves of different density, width, and depth, somewhere covered by folded metal, and somewhere totally interrupted and unbalanced as a result of the honing process imperfections. These features are crucial for a good liner’s function and are inspected from scanning electron microscope images by experts, which is subjective and time consuming process. Today, a fast automatic quality control is possible by using optical instruments to measure the liner’s topography, and a computer to calculate and check if the standard roughness and groove parameters are in tolerance. Therefore, combining the profile and image analysis, algorithms were developed to compute liner’s groove parameters from 3D interference measurements taken from three different types of cylinder bore surfaces of passenger cars. One of the surface types was a result of a test of an improved honing and the other two being currently in use. Then, the standard and new parameters (groove interruption, number of grooves, holes, etc) were incorporated in a characterisation tool to objectively and quickly evaluate the improvement of the liner’s quality for an updated monitoring in production.
|
|
| 7. |
|
|
| 8. |
- Dimkovski, Zlate, 1974-, et al.
(författare)
-
Quantification of Blechmantel Effect on Wear of Cylinder Bore Microtopography
- 2008
-
Ingår i: Proceedings of the 13th Nordic Symposium on Tribology, Nordtrib 2008. - Tampere : Tampere University Press. - 9789521519611 ; , s. 13-
-
Konferensbidrag (refereegranskat)abstract
- The presence of cold work material (blechmantel) smeared out on cylinder liners by faulty honing is undesirable as it seals the oil-bearing honing grooves. It is also believed to correlate with increased bore wear, presumably due to its loosening and together with the carbon build-up from the piston’s top land form an increased quantity of abrasive particles. An attempt has been made to estimate the extent of removal of blechmantel for different wear regimes present at the middle and top region (near the top dead centre) of the liner surface using the unworn bottom region as a reference for comparison. A number of truck cylinder liners were axially sectioned after varying periods of engine running under similar conditions of load, engine speed and lubrication. 3D surface measurements were taken at the three regions and a range of standard parameters was extracted. Combining the profile and image analysis, an algorithm was developed to identify and quantify the blechmantel covering the grooves that is most likely to break and act as abrasive wear particles and at the same time it represents the part of blechmantel which covers the most of the surface. It was found out that a mere portion of the blechmantel from the middle and bottom section was removed, while the blechmantel from the top section was greatly removed and thereby it represents one of the possible causes for wear. Axial wear scratches more emphasized on the thrust side of the liner were observed not only through the whole stroke area, but also in the bottom region. The fact that the most of the blechmantel is not removed from the running surface of the liner (except for the very small portion of the polished areas at the dead centres), points out that the blechmantel plays only a minor role on wear of the cylinder liner surfaces.
|
|
| 9. |
- Dimkovski, Zlate, 1974, et al.
(författare)
-
Quantification of the cold worked material inside the deep honing grooves on cylider liner surfaces and its effect on wear
- 2009
-
Ingår i: Wear. - Amsterdam : Elsevier BV. - 0043-1648 .- 1873-2577. ; 267:12, s. 2235-2242
-
Tidskriftsartikel (refereegranskat)abstract
- The increased presence of cold work material on cylinder liners due to the introduction of the diamond honing is undesirable as it seats the oil-bearing honing grooves. The most of it is a smeared metal inside the deep honing grooves (blechmantel) that may break and act as abrasive wear particles increasing the bore wear. An attempt has been made to estimate the extent of removal of blechmantel for different wear regimes present at the middle and top region (near the top dead centre) of the liner surface using the least worn bottom region as a reference for comparison. A number of truck grey iron cylinder liners were axially sectioned after varying periods of engine running under similar conditions of load, engine speed and lubrication. 3D surface measurements were taken at the three regions and a range of standard parameters was extracted. Combining the profile and image analysis, an algorithm was developed to identify and quantify the blechmantel. The algorithm has successfully identified/quantified the blechmantel and can be used for automatic surface quality and process control. It was found that the amount of the blechmantel in the middle section was approximately the same (though slightly lower) as that in the bottom section, while there was a considerable dislocation and removal of blechmantel in the top section and thereby it represents one of the possible causes for wear. Axial wear scratches of different size and distribution were observed not only through the whole stroke area, but also in the bottom region. All engines and liners performed well throughout the tests, and the observed quantities of blechmantel and axial scratches are acceptable for the time being.
|
|
| 10. |
- Dimkovski, Zlate, 1974-, et al.
(författare)
-
Towards 3D Characterisation of Cylinder Liner Surfaces
- 2008
-
Ingår i: Proceedings / XII. International Colloquium on Surfaces January 28th and 29th, 2008, Chemnitz, Germany = XII. Internationales Oberflächenkolloquium. - Aachen : Shaker Verlag. - 9783832269128 ; , s. 15-24
-
Konferensbidrag (refereegranskat)abstract
- Cylinder liner surface has a direct impact on the oil consumption and frictional losses in the internal combustion engines which are in common interest to be as lower as possible. Thus, the optimisation of the liner surface, its function and manufacture is often on the agenda of the automotive industry. Since the liner surface finish is a subject of improving, there is a need of improving and facilitating of its 3D characterisation preliminary when the parameter control limits are unknown, as well as later when it is experimentally verified and the limits are better determined. For that purpose a method for quality control in 3D of cylinder liners is proposed here. A tool was developed and implemented for rating of cylinder liner surfaces, computing of 3D groove parameters (groove width, height and distance between grooves) and determination of a needed number of measurements.
|
|
