| 1. |
- Winikka, Henrik, et al.
(författare)
-
Particle formation during pressurized entrained flow gasification of wood powder : Effects of process conditions on chemical composition, nanostructure, and reactivity
- 2018
-
Ingår i: Combustion and Flame. - : Elsevier BV. - 0010-2180 .- 1556-2921. ; 189, s. 1339-1351
-
Tidskriftsartikel (refereegranskat)abstract
- The influence of operating condition on particle formation during pressurized, oxygen blown gasification of wood powder with an ash content of 0.4 wt% was investigated. The investigation was performed with a pilot scale gasifier operated at 7 bar(a). Two loads, 400 and 600 kW were tested, with the oxygen equivalence ratio (λ) varied between 0.25 and 0.50. Particle concentration and mass size distribution was analyzed with a low pressure cascade impactor and the collected particles were characterized for morphology, elemental composition, nanostructure, and reactivity using scanning electron microscopy/high resolution transmission electron microscopy/energy dispersive spectroscopy, and thermogravimetric analysis. In order to quantify the nanostructure of the particles and identify prevalent sub-structures, a novel image analysis framework was used. It was found that the process temperature, affected both by λ and the load of the gasifier, had a significant influence on the particle formation processes. At low temperature (1060 °C), the formed soot particles seemed to be resistant to the oxidation process; however, when the oxidation process started at 1119 °C, the internal burning of the more reactive particle core began. A further increase in temperature (> 1313 °C) lead to the oxidation of the less reactive particle shell. When the shell finally collapsed due to severe oxidation, the original soot particle shape and nanostructure also disappeared and the resulting particle could not be considered as a soot anymore. Instead, the particle shape and nanostructure at the highest temperatures (> 1430 °C) were a function of the inorganic content and of the inorganic elements the individual particle consisted of. All of these effects together lead to the soot particles in the real gasifier environment having less and less ordered nanostructure and higher and higher reactivity as the temperature increased; i.e., they followed the opposite trend of what is observed during laboratory-scale studies with fuels not containing any ash-forming elements and where the temperature was not controlled by λ.
|
|
| 2. |
- Mellin, Pelle, 1985-, et al.
(författare)
-
Nano-sized by-products from metal 3D printing, composite manufacturing and fabric production
- 2016
-
Ingår i: Journal of Cleaner Production. - Sweden : Elsevier. - 0959-6526 .- 1879-1786. ; 139, s. 1224-1233
-
Tidskriftsartikel (refereegranskat)abstract
- Recently, the health and environmental perspective of nano-materials has gained attention. Most previous work focused on Engineered Nanoparticles (ENP). This paper examines some recently introduced production routes in terms of generated nano-sized by-products. A discussion on the hazards of emitting such particles and fibers is included. Fine by-products were found in recycled metal powder after 3D printing by Selective Laser Melting (SLM). The process somehow generated small round metal particles (~1e2 mm) that are possibly carcinogenic and respirable, but not small enough to enter by skin-absorption. With preventive measures like closed handling and masks, any health related effects can be prevented. The composite manufacturing in particular generated ceramic and carbonaceous particles that are very small and respirable but do not appear to be intrinsically toxic. The smallest features in agglomerates were about 30 nm. Small particles and fibers that were not attached in agglomerates were found in a wide range of sizes, from 1 μm and upwards. Preventive measures like closed handling and masks are strongly recommended. In contrast, the more traditional production route of fabric production is investigated. Here, brushing residue and recycled wool from fabric production contained few nano-sized by-products.
|
|
| 3. |
|
|
| 4. |
- Atashipour, Seyed Rasoul, et al.
(författare)
-
On the Shear Buckling of Clamped Narrow Rectangular Orthotropic Plates
- 2015
-
Ingår i: Mathematical problems in engineering (Print). - : Hindawi Limited. - 1024-123X .- 1563-5147. ; 2015
-
Tidskriftsartikel (refereegranskat)abstract
- This paper deals with stability analysis of clamped rectangular orthotropic thin plates subjected to uniformly distributed shear load around the edges. Due to the nature of this problem, it is impossible to present mathematically exact analytical solution for the governing differential equations. Consequently, all existing studies in the literature have been performed by means of different numerical approaches. Here, a closed-form approach is presented for simple and fast prediction of the critical buckling load of clamped narrow rectangular orthotropic thin plates. Next, a practical modification factor is proposed to extend the validity of the obtained results for a wide range of plate aspect ratios. To demonstrate the efficiency and reliability of the proposed closed-form formulas, an accurate computational code is developed based on the classical plate theory (CPT) by means of differential quadrature method (DQM) for comparison purposes. Moreover, several finite element (FE) simulations are performed via ANSYS software. It is shown that simplicity, high accuracy, and rapid prediction of the critical load for different values of the plate aspect ratio and for a wide range of effective geometric and mechanical parameters are the main advantages of the proposed closed-form formulas over other existing studies in the literature for the same problem.
|
|
| 5. |
|
|
| 6. |
|
|
| 7. |
- Nybacka, Mikael, et al.
(författare)
-
Project: CASTT - Centre for Automotive Systems Technologies and Testing
- 2007
-
Annan publikation (populärvet., debatt m.m.)abstract
- Through the Centre for Automotive Systems Technologies and Testing, Luleå University of Technology aims to first of all support automotive winter testing in Northern Sweden. This means to support the local automotive test entrepreneurs and through them their customers: the car manufacturers and their suppliers. To succeed in this task, the center relies on the university's areas of leading research and most importantly on the cooperation between those areas.
|
|
| 8. |
- Atashipour, Rasoul, 1983, et al.
(författare)
-
A weak shear web model for deflection analysis of deep composite box-type beams
- 2018
-
Ingår i: Engineering Structures. - : Elsevier BV. - 1873-7323 .- 0141-0296. ; 155, s. 36-49
-
Tidskriftsartikel (refereegranskat)abstract
- Deep box-type beams, consisting of framing members and sheathings, are sensitive to shear deformations andhence appropriate refined theories or complicated magnification factors are needed to be used to obtain accurate results. For sheathings or webs between the framing members that are weak in shear, additional shear deformations occur corresponding to the relative axial displacement between the framing members. These sandwich-type or partial interaction-type of in-plane shear behaviour between the framing members, needs to betaken into account, especially when the web shear stiffness is very low. The composite box-type beam treatedhere is composed of three framing members with sheathings on both sides. To incorporate effects of the sheathings shear deformations between the framing members on the deflection, the sheathings, here called web interlayers, are modelled as shear media with equivalent slip moduli corresponding to a partially interacting composite beam model. Governing equilibrium equations of the model are obtained using the minimum total potential energy principle and solved explicitly. The obtained results are compared with those based on different conventional beam theories and 3-D finite element (FE) simulations. It is shown that the model is capable of predicting accurately the deflection for a wide range of geometry and property parameters. It is demonstrated that the deflection of such deep box-type beams can be expressed as the summation of three different effects, namely bending deformations, conventional shear deformations in the framing members and sheathings, and additional in-plane shear deformations or shear slips of the weak web causing relative axial displacements between the framing members.
|
|
| 9. |
|
|
| 10. |
- Mangold, Mikael, 1982, et al.
(författare)
-
Building ownership, renovation investments, and energy performance - A study of multi-family dwellings in Gothenburg
- 2018
-
Ingår i: Sustainability. - : MDPI AG. - 2071-1050. ; 10:5
-
Tidskriftsartikel (refereegranskat)abstract
- The European building stock was renewed at a rapid pace during the period 1950-1975. In many European countries, the building stock from this time needs to be renovated, and there are opportunities to introduce energy efficiency measures in the renovation process. Information availability and increasingly available analysis tools make it possible to assess the impact of policy and regulation. This article describes methods developed for analyzing investments in renovation and energy performance based on building ownership and inhabitant socio-economic information developed for Swedish authorities, to be used for the Swedish national renovations strategy in 2019. This was done by analyzing measured energy usage and renovation investments made during the last 30 years, coupled with building specific official information of buildings and resident area characteristics, for multi-family dwellings in Gothenburg (N = 6319). The statistical analyses show that more costly renovations lead to decreasing energy usage for heating, but buildings that have been renovated during the last decades have a higher energy usage when accounting for current heating system, ownership, and resident socio-economic background. It is appropriate to include an affordability aspect in larger renovation projects since economically disadvantaged groups are over-represented in buildings with poorer energy performance.
|
|
