| 1. |
- Abele, H., et al.
(författare)
-
Particle physics at the European Spallation Source
- 2023
-
Ingår i: Physics reports. - : Elsevier. - 0370-1573 .- 1873-6270. ; 1023, s. 1-84
-
Forskningsöversikt (refereegranskat)abstract
- Presently under construction in Lund, Sweden, the European Spallation Source (ESS) will be the world’s brightest neutron source. As such, it has the potential for a particle physics program with a unique reach and which is complementary to that available at other facilities. This paper describes proposed particle physics activities for the ESS. These encompass the exploitation of both the neutrons and neutrinos produced at the ESS for high precision (sensitivity) measurements (searches).
|
|
| 2. |
- Adaldo, Antonio, et al.
(författare)
-
Cooperative coverage for surveillance of 3D structures
- 2017
-
Ingår i: IEEE International Conference on Intelligent Robots and Systems. - Piscataway, NJ : Institute of Electrical and Electronics Engineers (IEEE). - 9781538626825 ; , s. 1838-1845
-
Konferensbidrag (refereegranskat)abstract
- In this article, we propose a planning algorithm for coverage of complex structures with a network of robotic sensing agents, with multi-robot surveillance missions as our main motivating application. The sensors are deployed to monitor the external surface of a 3D structure. The algorithm controls the motion of each sensor so that a measure of the collective coverage attained by the network is nondecreasing, while the sensors converge to an equilibrium configuration. A modified version of the algorithm is also provided to introduce collision avoidance properties. The effectiveness of the algorithm is demonstrated in a simulation and validated experimentally by executing the planned paths on an aerial robot.
|
|
| 3. |
- Ahmed, Hesham, et al.
(författare)
-
Gas-Condensed Phase Reactions - A Novel Route to Synthesize Alloys and Intermetallics Involving Refractory Metals
- 2016
-
Ingår i: Materials Today: Proceedings. - : Elsevier. - 2214-7853.
-
Konferensbidrag (refereegranskat)abstract
- Reduction and simultaneous reduction-carburization of oxide mixtures to get intermetallics and composite materials may open up shorter process routes towards the end-user needs. The use of natural gas or hydrogen would be environment-friendly. With these aims, the corresponding kinetics were studied by thermogravimetry, gas chromatography as well as laser-flash method. It was found that, under identical conditions, the Arrhenius activation energy for the reduction is proportional to the thermodynamic stability of the compound reduced. Intermetallics could be synthesized successfully and the product was found to have nanograins. Also, Metallic coating on copper surfaces was successfully developed.
|
|
| 4. |
- Ahmed, Hesham, et al.
(författare)
-
Gas-Solid Reaction Route toward the Production of Intermetallics from Their Corresponding Oxide Mixtures
- 2016
-
Ingår i: Metals. - : MDPI AG. - 2075-4701. ; 6:8
-
Tidskriftsartikel (refereegranskat)abstract
- Near-net shape forming of metallic components from metallic powders produced in situ from reduction of corresponding pure metal oxides has not been explored to a large extent. Such a process can be probably termed in short as the "Reduction-Sintering" process. This methodology can be especially effective in producing components containing refractory metals. Additionally, in situ production of metallic powder from complex oxides containing more than one metallic element may result in in situ alloying during reduction, possibly at lower temperatures. With this motivation, in situ reduction of complex oxides mixtures containing more than one metallic element has been investigated intensively over a period of years in the department of materials science, KTH, Sweden. This review highlights the most important features of that investigation. The investigation includes not only synthesis of intermetallics and refractory metals using the gas solid reaction route but also study the reaction kinetics and mechanism. Environmentally friendly gases like H-2, CH4 and N-2 were used for simultaneous reduction, carburization and nitridation, respectively. Different techniques have been utilized. A thermogravimetric analyzer was used to accurately control the process conditions and obtain reaction kinetics. The fluidized bed technique has been utilized to study the possibility of bulk production of intermetallics compared to milligrams in TGA. Carburization and nitridation of nascent formed intermetallics were successfully carried out. A novel method based on material thermal property was explored to track the reaction progress and estimate the reaction kinetics. This method implies the dynamic measure of thermal diffusivity using laser flash method. These efforts end up with a successful preparation of nanograined intermetallics like Fe-Mo and Ni-W. In addition, it ends up with simultaneous reduction and synthesis of Ni-WN and Ni-WC from their oxide mixtures in single step.
|
|
| 5. |
- Ahmed, Hesham M., et al.
(författare)
-
Dynamic Thermal Diffusivity Measurements - A Tool for Studying Gas-Solid Reactions
- 2011
-
Ingår i: DIFFUSION IN SOLIDS AND LIQUIDS VI, PTS 1 AND 2. - Durnten-Zurich : Trans Tech Publications Inc.. ; , s. 217-222, s. 217-222
-
Konferensbidrag (refereegranskat)abstract
- In the present work, the thermal diffusivity measurements of uniaxially cold pressed NiWO(4) has been carried out. The measurements were performed isothermally at temperatures between 973 and 1273 K under H(2) gas using the laser flash technique. The experimental thermal diffusivity values were found to increase with the reduction progress as well as with increasing temperature. The calculated activation energy was found to be higher than that for chemically controlled reaction. The difference has been attributed to factors like agglomeration of the product as well as sintering of the precursor along with the chemical reaction. In order to sort out the sintering effect on the thermal diffusivity values, complementary experiments have been done on pressed NiWO(4) and Ni-W, produced by the reduction of NiWO(4) at 1123K, under Argon gas. The porosity change and its effect on thermal diffusivity values have been studied.
|
|
| 6. |
- Ahmed, Hesham M., 1981-
(författare)
-
Investigations of the Kinetics of Reduction and Reduction/Carburization of NiO-WO3 Precursors.
- 2010
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Kinetic studies of reduction of the mixtures of NiO and WO3 having different Ni/(Ni+W) molar ratios in flowing hydrogen gas were investigated by means of Thermo Gravimetric Analysis (TGA), Fluidized Bed (FB) technique as well as Thermal diffusivity measurements under isothermal conditions. In the case of TGA, the reaction progress was monitored by mass loss, while evolved gas analysis by a gas chromatograph was the indicator of the reaction progress in the case of FB. The results indicate that the reduction reaction proceeds through three consecutive steps, viz. NiO-WO3 Ni-WO3 Ni-WO2 Ni-W The present results show that the fluidized bed technique can be successfully utilized in bulk production of intermetallics containing W and a transition metal (or a composite material) wherein the process conditions would have a strong impact on the particle size of the end product. During the investigations, it was found that there was a delay in the reaction during the hydrogen reduction of NiO-WO3 mixed oxides in a fluidized bed reactor. In order to understand the same, a theoretical model was developed to estimate the apparent reaction rate constant for the reduction reaction from the intrinsic chemical reaction rate constant. Appropriate differential mass balance equations based on intrinsic chemical reaction rate constants and thermodynamic equilibria were developed. The proposed model was successfully applied in predicting the overall reaction kinetics of a fluidized bed reactor. This model is also suitable for scale-up calculations. SEM images showed that the particle size of the final product was dependent on the Ni/(Ni+W) molar ratio; smaller particles were formed at higher nickel contents. X-ray diffractions of the reduced precursors exhibited slight shift of Ni peaks from the standard one indicating the dissolution of W into Ni. A new method for studying kinetics of the hydrogen reduction of NiO-WO3 precursors was developed in which the reaction progress was monitored by following the change of thermal diffusivity of the precursors. Activation energies of reduction as well as sintering were calculated. This method is considered unique as it provides information regarding the physical changes like sintering, change of porosity and agglomeration along with the chemical changes occurring during the gas/solid reaction. As a continuation of the kinetic studies, Ni-W-C ternary carbides were synthesized by simultaneous reduction–carburization of Ni-W-O system using H2-CH4 gas mixtures by TGA. The results showed that the reduction of the oxide mixture was complete before the carburization took place. The nascent particles of the metals formed by reduction could react with the gas mixture with well-defined carbon potential to form a uniform product of Ni-W-C. The above-mentioned experiments were conducted in such a way to ensure that the reaction was controlled by the chemical reaction. The activation energies of the reduction as well as carburization processes at different stages were calculated accordingly. The present dissertation demonstrates the potential of the investigations of gas/solid reactions towards tailoring the process towards materials with optimized properties as for example introduction of interstitials. The present process design is extremely environment-friendly with reduced number of unit processes and the product being H2O.
|
|
| 7. |
- Ahmed, Hesham M., et al.
(författare)
-
Isothermal dynamic thermal diffusivity studies of the reduction of NiO and NiWO(4) precursors by hydrogen
- 2011
-
Ingår i: International Journal of Materials Research - Zeitschrift für Metallkunde. - : Walter de Gruyter GmbH. - 1862-5282 .- 2195-8556. ; 102:11, s. 1336-1344
-
Tidskriftsartikel (refereegranskat)abstract
- Thermal diffusivity measurements of uniaxially cold pressed NiO and NiWO(4) were carried out in a dynamic mode in order to monitor the kinetics of hydrogen reduction of the above-mentioned materials using a laser flash unit. The calculated activation energy was found to be higher than that for chemically-controlled reaction obtained earlier by thermogravimetry. The difference has been attributed to physical changes occurring along with the chemical reaction. The activation energy of sintering of the products was evaluated to be 33 and 36 kJ.mol(-1) for NiO and NiWO(4), respectively. Thermal conductivities were calculated taking into consideration the change in heat capacity considering the compositional and the structural changes with the progress of the reaction. The potentiality of the laser-flash method as a complementary technique to thermogravimetry in understanding the mechanism of gas solid reactions is discussed.
|
|
| 8. |
- Ahmed, Hesham M., et al.
(författare)
-
Kinetics and Mathematical Modeling of Hydrogen Reduction of NiO-WO(3) Precursors in Fluidized Bed Reactor
- 2011
-
Ingår i: ISIJ International. - : Iron and Steel Institute of Japan. - 0915-1559 .- 1347-5460. ; 51:9, s. 1383-1391
-
Tidskriftsartikel (refereegranskat)abstract
- In the present work, Fluidized bed reduction of NiO-WO(3) precursors was investigated isothermally at temperatures 973-1 273 K. The reaction progress was monitored by analysis of H(2)O evolved during the reaction process using a gas chromatograph instrument. A theoretical model based on intrinsic chemical reaction rate constants and thermodynamic equilibria was developed to estimate the apparent reaction rate constant for the reduction reaction. In developing the model, the particles are considered to be in a completely mixed condition and gas flow is described as plug flow. The proposed model is also suitable for scale-up calculations. The interfacial chemical reaction model was found to fit the experimental results. The apparent activation energy values of the reduction process at different stages were calculated accordingly. The present investigation proved that the fluidized bed technique can be successfully utilized in bulk production of intermetallics containing W and a transition metal (or a composite material) wherein the process conditions would have a strong impact on the particle size of the end product.
|
|
| 9. |
- Ahmed, Hesham M., et al.
(författare)
-
Kinetics of Reduction of NiO-WO3 Mixtures by Hydrogen
- 2010
-
Ingår i: Metallurgical and materials transactions. B, process metallurgy and materials processing science. - : Springer Science and Business Media LLC. - 1073-5615 .- 1543-1916. ; 41:1, s. 161-172
-
Tidskriftsartikel (refereegranskat)abstract
- The kinetics of reduction of the oxide mixtures of Ni-W with different Ni/(Ni-W) molar ratios within the range of 923 K to 1173 K in flowing hydrogen gas was investigated by means of thermogravimetric analysis under isothermal conditions. The products were examined by X-ray diffraction, scanning electron microscope (SEM), and electron dispersion spectroscopy (EDS) analyses. Five different oxide mixtures apart from the pure oxides were studied in the present work. The results indicate that the reduction reaction proceeds through three consecutive steps that are as follows: NiO-WO3 -> Ni-WO3 -> Ni-WO2 -> Ni-W From the experimental results, the Arrhenius activation energies of the three steps were evaluated for all of the studied compositions. The activation energy for the first step was calculated to be approximately 18 kJ/mol. For the second and third stages, the activation energy values varied from 62 to 38 kJ/mol for the second stage and 51 to 34 kJ/mol for the third stage depending on the Ni/(Ni + W) molar ratio in the precursors; the activation energy increased with increasing ratios. SEM images showed that the grain size of the final product was dependent on the Ni/(Ni + W) molar ratio; smaller grains were formed at higher nickel contents.
|
|
| 10. |
- Ahmed, Hesham M., et al.
(författare)
-
Reduction-Carburization of NiO-WO3 Under Isothermal Conditions Using H2-CH4 Gas Mixture
- 2010
-
Ingår i: Metallurgical and materials transactions. B, process metallurgy and materials processing science. - : Springer Science and Business Media LLC. - 1073-5615 .- 1543-1916. ; 41:1, s. 173-181
-
Tidskriftsartikel (refereegranskat)abstract
- Ni-W-C ternary carbides were synthesized by simultaneous reduction–carburization of NiO-WO3 oxide precursors using H2-CH4 gas mixtures in the temperature range of 973 to 1273 K. The kinetics of the gas–solid reaction were followed closely by monitoring the mass changes using the thermogravimetric method (TGA). As a thin bed of the precursors were used, each particle was in direct contact with the gas mixture. The results showed that the hydrogen reduction of the oxide mixture was complete before the carburization took place. The nascent particles of the metals formed by reduction could react with the gas mixture with well-defined carbon potential to form a uniform product of Ni-W-C. Consequently, the reaction rate could be conceived as being controlled by the chemical reaction. From the reaction rate, Arrhenius activation energies for reduction and carburization were evaluated. Characterization of the carbides produced was carried out using X-ray diffraction and a scanning electron microscope (SEM) combined with electron dispersion spectroscopy (SEM-EDS) analyses. The grain sizes also were determined. The process parameters, such as the temperature of the reduction–carburization reaction and the composition of the gas mixture, had a strong impact on the carbide composition as well as on the grain size. The results are discussed in light of the reduction kinetics of the oxides and the thermodynamic constraints.
|
|
