| 1. |
- Blomfors, Mattias, 1990, et al.
(författare)
-
Engineering Assessment Method for Anchorage in Corroded Reinforced Concrete
- 2016
-
Ingår i: IABSE Congress Stockholm 2016. - : IABSE c/o ETH Hönggerberg. - 9783857481444 ; , s. 2109-2116
-
Konferensbidrag (refereegranskat)abstract
- There is an increasing need for reliable methods to assess load-carrying capacity and remaining service life of existing infrastructure. Several previous research projects have resulted in a verified, simple 1D model for assessment of anchorage in corroded reinforced concrete structures. Previous verification has involved both experiments and detailed 3D NLFE analyses. To further develop the 1D model it needs to be extended to comprise more practical situations. In order to facilitate an efficient extension procedure in the future, the size of 3D NLFE model that is required to capture the bond behaviour between corroded reinforcement and concrete is investigated. Beam-end models and models of sub-sections were studied, and the results in terms of bond stress and crack pattern were compared. Preliminary results indicate good agreement for some situations; however for some cases a section model seems to overestimate the capacity.
|
|
| 2. |
- Blomfors, Mattias, 1990, et al.
(författare)
-
Practical bond model for corroded RC bridges
- 2017
-
Ingår i: High Tech Concrete. - Cham : Springer International Publishing. - 2617-4820. - 9783319594705 ; , s. 1793-1803
-
Konferensbidrag (refereegranskat)abstract
- Corrosion of steel reinforcement is a common cause of deterioration in reinforced concrete bridges and many existing bridges are damaged to varying degrees. The rate of deterioration of the bridge stock has been shown to increase due to climate change. Unsympathetically, the demand for load-carrying capacity is however often increased with time. Therefore there is an increasing need for reliable methods to assess the load-carrying capacity and remaining service-life of existing infrastructure. A simple model for the assessment of Anchorage in corroded Reinforced Concrete structures (ARC) has previously been developed. It was originally based on fib Model Code 1990 and has been verified with experiments and three-dimensional nonlinear finite element (3D NLFE) analyses for both accelerated and natural corrosion as well as for different degrees of corrosion. The model was applied when assessing two road bridges in Sweden. The investigation demonstrated great cost savings but also areas for improvement, in particular regarding (a) applicability to practical cases and (b) incorporation of uncertainties in the assessment. The primary focal point of this paper is to present an overview of the development of the ARC model together with recent verifications against a large bond test database as well as foreseen future developments. It was found that the ARC model represents the physical behaviour reasonably well, and gives conservative values of bond strength compared to the bond tests database. In future works, among others, uncertainties of the input variables will be incorporated by means of probabilistic modelling, making way for implementation of the ARC model into semi-probabilistic safety concepts by extraction of modification factors. Overall, with more accurate and reliable assessment methods for corroded RC structures, environmental and economic savings are imminent as more of the potential of existing structures can be realized.
|
|
| 3. |
- Blomfors, Martin, et al.
(författare)
-
Reliability analysis of corroded reinforced concrete beam with regards to anchorage failure
- 2019
-
Ingår i: Life-Cycle Analysis and Assessment in Civil Engineering. - : CRC Press/Balkema. - 9781138626331 - 9781351857574 ; , s. 337-344, s. 337-344
-
Konferensbidrag (refereegranskat)abstract
- Reinforcement corrosion is a common problem in reinforced concrete infrastructure today, and it is expected to increase in the future. To simply replace the corroded structures with new ones requires large resources, both in financial and environmental terms. Therefore it is important that existing structures are used to their full potential, also after the onset of corrosion. This paper presents a reliability study of the anchorage capacity of a reinforced concrete beam including reinforcement corrosion. The sensitivity of the different input parameters is also studied. As expected, the results show that the reliability is reduced with corrosion; the magnitude depends to a large extent on the modelling uncertainty used for the bond model for corroded reinforcement. The sensitivity analysis shows an influence of corrosion also on the sensitivities of the input parameters, which is expected based on the properties of the underlying bond model. This paper demonstrates that probabilistic evaluations give valuable insight of the reliability, which can be used to prolong the service-life of existing infrastructure and save both money and the environment.
|
|
| 4. |
- Blomfors, Mattias, 1990, et al.
(författare)
-
Reliable engineering assessments of corroded concrete structures
- 2017
-
Ingår i: Nordic Concrete Research : Proceedings of the XXIII Nordic Concrete Research Symposium, Aalborg, Denmark, 21-23 August, 2017 - Proceedings of the XXIII Nordic Concrete Research Symposium, Aalborg, Denmark, 21-23 August, 2017. ; , s. 245-248
-
Konferensbidrag (refereegranskat)abstract
- Corrosion of steel reinforcement is a large and increasing problem for reinforced concrete structures. Simple and reliable assessment methods are required to use the full capacity of existing infrastructure. In this paper, a reliable engineering assessment method is outlined. A model for anchorage has been developed and verified against a large database of bond tests. Also the influence of corrosion on the bending and shear capacity is to be included, and a probabilistic model will be established. The outcome of this work will enable practising engineers to perform reliable assessments of concrete structures with corroded reinforcement.
|
|
| 5. |
- Honfi, Daniel, et al.
(författare)
-
Decision support for maintenance and upgrading of existing bridges
- 2017
-
Ingår i: IABSE Conference, Vancouver 2017. - : International Association for Bridge and Structural Engineering (IABSE). - 9783857481536 ; 109, s. 336-345, s. 336-345
-
Konferensbidrag (refereegranskat)abstract
- Maintenance of transportation infrastructure assets can be relatively expensive, since it does not only include the direct cost of interventions, but also the indirect consequences of traffic disruptions. To make optimal decisions about maintenance actions, including rehabilitation and upgrading, reliable information about the performance of existing structures is needed. However, obtaining such information might require significant efforts and can be done in various ways. The purpose of an ongoing Swedish research project BIG BRO is to develop a framework for a decision support methodology that can be used for implementing maintenance strategies for bridges on a rational basis. The present paper provides a brief overview about the project as well as describes some of the ongoing work.
|
|
