| 1. |
- Akter, Shaheda T., et al.
(författare)
-
A numerical study of the stiffness and strength of cross-laminated timber wall-to-floor connections under compression perpendicular to the grain
- 2021
-
Ingår i: Buildings. - : MDPI AG. - 2075-5309. ; 11:10
-
Tidskriftsartikel (refereegranskat)abstract
- The use of cross-laminated timber (CLT) in multi-story buildings is increasing due to the potential of wood to reduce green house gas emissions and the high load-bearing capacity of CLT. Compression perpendicular to the grain (CPG) in CLT is an important design aspect, especially in multi-storied platform-type CLT buildings, where CPG stress develops in CLT floors due to loads from the roof or from upper floors. Here, CPG of CLT wall-to-floor connections are studied by means of finite element modeling with elasto-plastic material behavior based on a previously validated Quadratic multi-surface (QMS) failure criterion. Model predictions were first compared with experiments on CLT connections, before the model was used in a parameter study, to investigate the influence of wall and floor thicknesses, the annual ring pattern of the boards and the number of layers in the CLT elements. The finite element model agreed well with experimental findings. Connection stiffness was overestimated, while the strength was only slightly underestimated. The parameter study revealed that the wall thickness effect on the stiffness and strength of the connection was strongest for the practically most relevant wall thicknesses between 80 and about 160 mm. It also showed that an increasing floor thickness leads to higher stiffness and strength, due to the load dispersion effect. The increase was found to be stronger for smaller wall thicknesses. The influence of the annual ring orientation, or the pith location, was assessed as well and showed that boards cut closer to the pith yielded lower stiffness and strength. The findings of the parameter study were fitted with regression equations. Finally, a dimensionless ratio of the wall-to-floor thickness was used for deriving regression equations for stiffness and strength, as well as for load and stiffness increase factors, which could be used for the engineering design of CLT connections.
|
|
| 2. |
|
|
| 3. |
- Akter, Shaheda T., et al.
(författare)
-
Numerical modelling of wood under combined loading of compressionperpendicular to the grain and rolling shear
- 2021
-
Ingår i: Engineering structures. - : Elsevier. - 0141-0296 .- 1873-7323. ; 244
-
Tidskriftsartikel (refereegranskat)abstract
- Numerical modeling is an efficient tool for experimental validation and for gaining a deeper understanding of complex material phenomena, especially when causal relationships are overlaid by material variability. Wood is such a highly orthotropic and complex material, which in engineering problems however is considered as macro- homogeneous. The aim of this study is to numerically investigate stress and strain states of wood in the radial- tangential plane and the influence of the orthotropic material behavior on the structural response. Model vali-dation is based on experiments performed on clear wood of Norway spruce (Picea abies) by using a biaxial test setup. Three material models were used, namely Hill’s plasticity model, the Hoffman criterion and a novel quadratic multi-surface (QMS) criterion. After validation on the local material scale, the models were applied to the engineering problem of compression perpendicular to the grain for studying the effect of the unloaded length. As a novel part, the influence of the annual ring structure on the local material behavior and the global elasto- plastic force–displacement behavior of wood under compression perpendicular to the grain were numerically investigated. Hill’s failure criterion was found to be the least suitable at both length scales, local material behavior and global structural response. The Hoffman and the QMS criteria showed quite good agreement with the biaxial experiments in terms of force–displacement relations and strain distributions for different loading situations, especially for combinations with radial compression, while there was less agreement with experiments for the behavior of combinations with tangential compression. Application of these material models to compression perpendicular to the grain for studying the unloaded length effect yielded similar trends as observed in structural tests. A reasonable and similar force–displacement response by Hoffman and QMS criteria was observed, while Hill’s model yielded significantly overestimated force carrying capacity. Differences in force-–displacement response for different loading situations were well in line with literature findings and the infl-ence of the annual ring curvature on the overall force–displacement behavior could be quantified.
|
|
| 4. |
- Bader, Thomas K., 1980-, et al.
(författare)
-
Dowel deformations in multi-dowel LVL-connections under moment loading
- 2015
-
Ingår i: Wood Material Science & Engineering. - : Taylor & Francis. - 1748-0272 .- 1748-0280. ; 10:3, s. 216-231
-
Tidskriftsartikel (refereegranskat)abstract
- The aim of the experimental study presented herein is the assessment and quantification of the behavior of individual dowels in multi-dowel connections loaded by a bending moment. For this purpose, double-shear, steel-to-timber connections with nine steel dowels arranged in different patterns and with different dowel diameters were tested in four-point bending. In order to achieve a ductile behavior with up to 7° relative rotation, the connections were partly reinforced with self-tapping screws. The reinforcement did not influence the global load–deformation behavior, neither for dowel diameters of 12 mm nor for 20 mm, as long as cracking was not decisive. The deformation of the individual dowels was studied by means of a non-contact deformation measurement system. Thus, the crushing deformation, that is, the deformation at the steel plate, and the bending deformation of the dowels could be quantified. In the case of 12 mm dowels, the bending deformation was larger than the crushing deformation, while it was smaller in the case of 20 mm dowels. Moreover, dowels loaded parallel to the grain showed larger bending deformations than dowels loaded perpendicular to the grain. This indicates that the loading of the individual dowels in the connection differs depending on their location.
|
|
| 5. |
- Bader, Thomas K., 1980-, et al.
(författare)
-
Experimental characterization of the global and local behavior of multi-dowel LVL-connections under complex loading
- 2016
-
Ingår i: Materials and Structures. - : Springer Science and Business Media LLC. - 1359-5997 .- 1871-6873. ; 49:6, s. 2407-2424
-
Tidskriftsartikel (refereegranskat)abstract
- The thorough experimental characterization of a dowel-type connection under various combinations of bending moments and normal forces is presented in this study. Double-shear steel-to-timber connections with 12 and 20 mm steel dowels were tested in a 4-point bending test set-up. The load, between the connected steel and wood beams, was transferred by the dowels themselves and also via an additional (passive) contact device, which introduced an eccentric normal force in the timber beam. The behavior of the connections was studied at the global scale of the connection and at the local scale of the individual dowels. A non-contact deformation measurement system was used to assess the changes of the location of the center of relative rotation over the entire loading. At the same time, the head deformations of the individual dowels could be measured, giving a direct indication about the force distribution among the dowels. Due to reinforcement, connections behaved distinctly ductile with a global relative rotation of up to 3°. Pre-stressing of the contact device by a force of 40 kN yielded an even stiffer behavior. For the particular configurations tested herein, the center of rotation was found to be close to the vertical axis of symmetry of the joint and close to the top row of the dowels. Moreover, the superimposed vertical shift of the center of relative rotation in case of a delayed normal force could be quantified. © 2015 RILEM
|
|
| 6. |
- Bader, Thomas K., et al.
(författare)
-
Integrative experimental characterization and engineering modeling of single-dowel connections in LVL
- 2016
-
Ingår i: Construction and Building Materials. - : Elsevier BV. - 0950-0618 .- 1879-0526. ; 107, s. 235-246
-
Tidskriftsartikel (refereegranskat)abstract
- In order to be able to realistically and consistently elucidate and subsequently simulate the load displacement behavior of single-dowel connections, the material behavior of the individual components, namely steel dowels and wood, needs to be investigated. The behavior of slotted-in, single-dowel steel-to-laminated veneer lumber (LVL) connections with dowel diameters of 12 and 20 mm is thoroughly discussed here in relation to steel dowel and LVL properties. In addition to connection tests at different load-to-grain directions of 0, 45 and 90, the corresponding embedment behavior of LVL was tested up to dowel displacements of three times the dowel diameter. The material behavior of steel dowels was studied by means of tensile and 3-point bending tests and accompanying finite element simulations. A pronounced nonlinear behavior of the single-dowel connections was observed for all load-to-grain directions. In case of loading perpendicular to the grain, a significant hardening behavior was obvious. Due to the anisotropic material properties of wood, enforcing a loading direction of 45 to the grain resulted in an additional force perpendicular to the load direction which was quantified in a novel biaxial test setup. Thus, a comprehensive and consistent database over different scales of observations of dowel connections could be established, which subsequently was exploited by means of engineering modeling. The comparison of experimental and numerical data illustrates the potential of the engineering modeling approach to overcome drawbacks of current design regulations, which are unable to appropriately predict stiffness properties of dowel connections. Moreover, the quasi-elastic limit of dowel connections was calculated and discussed by means of the model. (c) 2016 Elsevier Ltd. All rights reserved.
|
|
| 7. |
- Dorn, Michael, 1978-, et al.
(författare)
-
Determination of coefficients of friction for laminated veneer lumber on steel under high pressure loads
- 2021
-
Ingår i: Friction. - : Springer. - 2223-7690 .- 2223-7704. ; 9, s. 367-379
-
Tidskriftsartikel (refereegranskat)abstract
- In this study, static coefficients of friction for laminated veneer lumber on steel surfaces were determined experimentally. The focus was on the frictional behaviors at different pressure levels, which were studied in combination with other influencing parameters: fiber orientation, moisture content, and surface roughness. Coefficients of friction were obtained as 0.10-0.30 for a smooth steel surface and as high as 0.80 for a rough steel surface. Pressure influenced the measured coefficients of friction, and lower normal pressures yielded higher coefficients. The influence of fiber angle was observed to be moderate, although clearly detectable, thereby resulting in a higher coefficient of friction when sliding perpendicular rather than parallel to the grain. Moist specimens contained higher coefficients of friction than oven-dry specimens. The results provide realistic values for practical applications, particularly for use as input parameters of numerical simulations where the role of friction is often wrongfully considered.
|
|
| 8. |
- Dorn, Michael, 1978-, et al.
(författare)
-
Development of large-scale load-bearing timber-glass structural elements
- 2014
-
Ingår i: WCTE 2014 - World Conference on Timber Engineering.
-
Konferensbidrag (refereegranskat)abstract
- The building industry demands ever more effective structural elements with a multitude of requirements at the same time. There is increasing interest for load-bearing glass elements which can be deployed in timber structures, e.g. in the outer façade or as column or beam elements within the building. In an on-going research project, the materials glass, timber and the adhesive combining the former have to be selected to fit each other but also suit the application. The mechanical properties are studied individually as well as in combined small-scale specimens experimentally. Furthermore,large-scale tests on beams and shear walls are performed. This is accompanied by numerical analysis to study a wide range of dimensions and variations as well as specific design situations. The final output of the project will be prototypes to beused in showcase projects.
|
|
| 9. |
|
|
| 10. |
- Kozłowski, Marcin, et al.
(författare)
-
Experimental investigation on timber-glass composite I-beams
- 2014
-
Ingår i: Challenging Glass 4- Structural Glass-Novel design methods and next generation products. - : Taylor & Francis. - 9781138001640
-
Konferensbidrag (refereegranskat)abstract
- Timber-glass composite I-beams were manufactured and tested in bending to failure. The glass web of the I-beam was adhesively bonded to the timber flanges using three different adhesives: Epoxy, Acrylate and Silicone. For the webs two types of 8 mm thick glass were used: annealed float and heat heat-strengthened glass. Before testing the beams with heat-strengthened glass, the residual-stress profile through the thickness of the glass panels was measured using a portable scattered light polariscope SCALP. The results show that the beam stiffness was similar for the acrylate and epoxy-bonded beams, despite the difference in adhesive stiffness. The beams bonded with the silicone adhesive showed approximately 25% lower stiffness. In terms of load bearing capacity, the beams made using heat-strengthened glass were approximately 50% stronger than the beams made using annealed float, for the epoxy and acrylate adhesive. Using the silicone adhesive, the increase was approximately 20%.
|
|
