| 1. |
- Busson, P., et al.
(författare)
-
Ferroelectric liquid crystalline dendrimers : Synthesis, thermal behavior, and electrooptical characterization
- 2001
-
Ingår i: Macromolecules. - : American Chemical Society (ACS). - 0024-9297 .- 1520-5835. ; 34:5, s. 1221-1229
-
Tidskriftsartikel (refereegranskat)abstract
- The preparation and characterization of a series of novel ferroelectric liquid crystalline dendrimers are presented. End-capping of 1-, 2-, and 3-generation dendrimers based on 2,2-bis(hydroxymethyl)propionic acid with mesogens gave surface-functionalized liquid crystalline compounds with 6, 12, and 24 mesogen-containing units, respectively. 4 -((R)-1-Methylheptyloxy)phenyl 4-(4 '-[10(hydroxycarbonyl)decyloxyl phenyl)benzoate was synthesized and used as a mesogen-containing unit. The purity and structure of each compound were determined by H-1 NMR spectroscopy, size exclusion chromatography, and elemental analysis. Differential scanning calorimetry and optical microscopy were used to investigate the mesomorphic properties of the mesogen-functionalized dendrimers. The materials displayed a variety of mesophases, including the smectic C* phase. All the liquid crystalline dendrimers showed ferroelectricity, and tilt angle and spontaneous polarization measurements were performed. The obtained results show that the ferroelectric properties of the materials are independent of the generation number of the dendritic scaffold.
|
|
| 2. |
- Busson, P., et al.
(författare)
-
Preparation of mesogen-functionalized dendrimers for second-order nonlinear optics
- 2002
-
Ingår i: Macromolecules. - : American Chemical Society (ACS). - 0024-9297 .- 1520-5835. ; 35:5, s. 1663-1671
-
Tidskriftsartikel (refereegranskat)abstract
- Liquid crystalline dendrimers with peripheral mesogen-containing units have been prepared. Multistep synthesis with several selective reactions was used in the preparation of the mesogen-containing molecules, 4-[10-(hydroxycarbonyl)decyloxy]phenyl 4-[4'-(2-(R)-octyloxy)-3'-nitrophenyl]benzo ate and 4-[10-(hydroxycarbonyl)decyloxy]biphenyl 4-[4'-(2-(R)-octyloxy)-3'-nitrophenyl]benzoate. Both molecules possessed an electron-accepting nitro group placed perpendicular to the long axis of the molecules in order to enhance the nonlinear optical activity. A second generation hydroxyl functional aliphatic dendrimer based on the dihydroxy acid, 2,2-bis(hydroxymethyl)propionic acid, was used as dendritic scaffold and was subsequently functionalized with the aforementioned groups. The purity and structure of the two liquid crystalline dendrimers were determined by H-1 NMR spectroscopy, size exclusion chromatography, and elemental analysis. The synthesis of both the mesogen-containing units and the liquid crystalline dendrimers is described in detail. Investigation of the liquid crystalline properties of the materials by differential scanning calorimetry and optical microscopy showed that they exhibited different mesophases, including the chiral smectic C phase. Ferroelectric switching was observed in this tilted phase, and electrooptical properties, including tilt angle and spontaneous polarization measurements, were investigated. Finally, the nonlinear optical properties of one of the materials were preliminary characterized.
|
|
| 3. |
- Jonas, Örtegren, et al.
(författare)
-
Cone motion viscosity and optical second harmonic generation of ferroelectric liquid crystalline dendrimers
- 2001
-
Ingår i: Liquid crystals (Print). - : Informa UK Limited. - 0267-8292 .- 1366-5855. ; 28:6, s. 861-868
-
Tidskriftsartikel (refereegranskat)abstract
- We report second harmonic generation in a ferroelectric liquid crystalline trimer and ferroelectric liquid crystalline dendrimers of first, second and third generation. Thin cells were filled with the compounds by capillary forces at elevated temperature, and cooled from the surface stabilized ferroelectric state to below the glass transition temperature, while kept in an electric field. The cone motion viscosity and the threshold electric field for unwinding of the helix axis of the chiral tilted smectic mesophases were studied separately at elevated temperature, and these data were used to optimize the preparation of the films. The measured response time was between 0.3 and 3 ms, which corresponds to a cone motion viscosity between 0.5 and 50 Pa s. Second harmonic generation was studied both at elevated temperature with an electric field and at room temperature with and without electric field. The first generation dendrimer exhibited a strong increase in the second order non-linear optical response with time at room temperature. The d(23)-coefficient of this dendrimer was approximately four times larger than for the other macromolecules and was 0.045 pm V-1. The relatively large d-coefficient of the first generation dendrimer is ascribed to crystallization, which improved the orientation of the molecular dipoles.
|
|
| 4. |
- Rehberger, Marcus, et al.
(författare)
-
VDP on packaging : Elementary velocity study on inkjet-printed papers for corrugated board production
- 2010
-
Ingår i: Proceedings of the Technical Association of the Graphic Arts, TAGA. - 9781935185024
-
Konferensbidrag (refereegranskat)abstract
- The idea of the “HybSpeed Printing” Project at Innventia AB is to facilitate the combination of a conventional printing process with inkjet printing, in-line, in the converting process. Inkjet print is “the” printing technique for adding variable data to a conventional printed layout (van Daele, 2005). It is already available, but the current processes do not guarantee high quality print at high speed, but the constant progress in inkjet technology will mean that this is soon provided. The aim of the present project is to evaluate the practicability of attaining high quality variable data print (VDP) at high speed. In 2008, an exploratory test was conducted on a Kodak Versamark DP5240 in Örnsöldsvik, Sweden, in cooperation with the Digital Printing Centre (DPC). As already mentioned, speed is probably the greatest issue facing the inkjet system. Flexo presses, for example, are running at a speed of 1000-1500 fpm, but the maximum speed of the inkjet test rig at DPC is 1000 fpm (5.08 m/s). Hence, this inkjet unit almost achieves the minimum requirements in speed. The question is how does the inkjet print quality at maximum speed differ from that at lower speed? The results reveal that speed has a slight influence on the print quality and that the line thickness and print density can be compensated for by changing the print layout. To minimize the line raggedness at high speed, other counter-measures have to be considered. However, the choice of paper had a greater influence and these issues are also discussed.
|
|
