| 1. |
- Abbaspour Asadollah, Sara, et al.
(författare)
-
Evaluation of surface EMG-based recognition algorithms for decoding hand movements
- 2019
-
Ingår i: Medical and Biological Engineering and Computing. - : Springer. - 0140-0118 .- 1741-0444. ; 58:1, s. 83-100
-
Tidskriftsartikel (refereegranskat)abstract
- Myoelectric pattern recognition (MPR) to decode limb movements is an important advancement regarding the control of powered prostheses. However, this technology is not yet in wide clinical use. Improvements in MPR could potentially increase the functionality of powered prostheses. To this purpose, offline accuracy and processing time were measured over 44 features using six classifiers with the aim of determining new configurations of features and classifiers to improve the accuracy and response time of prosthetics control. An efficient feature set (FS: waveform length, correlation coefficient, Hjorth Parameters) was found to improve the motion recognition accuracy. Using the proposed FS significantly increased the performance of linear discriminant analysis, K-nearest neighbor, maximum likelihood estimation (MLE), and support vector machine by 5.5%, 5.7%, 6.3%, and 6.2%, respectively, when compared with the Hudgins’ set. Using the FS with MLE provided the largest improvement in offline accuracy over the Hudgins feature set, with minimal effect on the processing time. Among the 44 features tested, logarithmic root mean square and normalized logarithmic energy yielded the highest recognition rates (above 95%). We anticipate that this work will contribute to the development of more accurate surface EMG-based motor decoding systems for the control prosthetic hands. [Figure not available: see fulltext.].
|
|
| 2. |
|
|
| 3. |
- Adawi, Tom, 1970, et al.
(författare)
-
Characterizing Software Engineering Students' Discussions during Peer Instruction : Opportunities for Learning and Implications for Teaching
- 2016
-
Ingår i: International Journal of Engineering Education. - 0949-149X. ; 32:2, s. 927-936
-
Tidskriftsartikel (refereegranskat)abstract
- Peer instruction is a method for activating students during lectures, which has gained a considerable amount of attention in higher education due to claims of dramatic improvement in learning gains. The purpose of this qualitative research study is to investigate what types of discussions engineering students engage in during a peer instruction session and what learning possibilities that are enabled by these different types of discussions. We observed twelve students during six separate and simulated peer instruction sessions and the students were interviewed individually after the sessions.Ananalysis of the data revealed that the students engaged in three qualitatively different types of discussions: affirmative discussions, motivating discussions, and argumentative discussions. We characterize these different types of discussions in terms of the number of alternative answers the students discuss, the extent to which they draw on prior knowledge and experiences, as well as the fundamental difference between an explanation and an argument. A good opportunity for learning is opened up when students are aspiring to find the truth, not simply being satisfied with what they believe to be true. We conclude that students do not always engage in discussions that support their learning in the best way, and we discuss implications for using peer instruction as a teaching method.
|
|
| 4. |
- Adeboye, Peter, 1982, et al.
(författare)
-
Catabolism of coniferyl aldehyde, ferulic acid and p-coumaric acid by Saccharomyces cerevisiae yields less toxic products
- 2015
-
Ingår i: Microbial Cell Factories. - : Springer Science and Business Media LLC. - 1475-2859. ; 14:1, s. 149-
-
Tidskriftsartikel (refereegranskat)abstract
- Background: Lignocellulosic substrates and pulping process streams are of increasing relevance to biorefineries for second generation biofuels and biochemical production. They are known to be rich in sugars and inhibitors such as phenolic compounds, organic acids and furaldehydes. Phenolic compounds are a group of aromatic compounds known to be inhibitory to fermentative organisms. It is known that inhibition of Sacchromyces cerevisiae varies among phenolic compounds and the yeast is capable of in situ catabolic conversion and metabolism of some phenolic compounds. In an approach to engineer a S. cerevisiae strain with higher tolerance to phenolic inhibitors, we selectively investigated the metabolic conversion and physiological effects of coniferyl aldehyde, ferulic acid, and p-coumaric acid in Saccharomyces cerevisiae. Aerobic batch cultivations were separately performed with each of the three phenolic compounds. Conversion of each of the phenolic compounds was observed on time-based qualitative analysis of the culture broth to monitor various intermediate and final metabolites. Result: Coniferyl aldehyde was rapidly converted within the first 24 h, while ferulic acid and p-coumaric acid were more slowly converted over a period of 72 h. The conversion of the three phenolic compounds was observed to involved several transient intermediates that were concurrently formed and converted to other phenolic products. Although there were several conversion products formed from coniferyl aldehyde, ferulic acid and p-coumaric acid, the conversion products profile from the three compounds were similar. On the physiology of Saccharomyces cerevisiae, the maximum specific growth rates of the yeast was not affected in the presence of coniferyl aldehyde or ferulic acid, but it was significantly reduced in the presence of p-coumaric acid. The biomass yields on glucose were reduced to 73 and 54 % of the control in the presence of coniferyl aldehyde and ferulic acid, respectively, biomass yield increased to 127 % of the control in the presence of p-coumaric acid. Coniferyl aldehyde, ferulic acid and p-coumaric acid and their conversion products were screened for inhibition, the conversion products were less inhibitory than coniferyl aldehyde, ferulic acid and p-coumaric acid, indicating that the conversion of the three compounds by Saccharomyces cerevisiae was also a detoxification process. Conclusion: We conclude that the conversion of coniferyl aldehyde, ferulic acid and p-coumaric acid into less inhibitory compounds is a form of stress response and a detoxification process. We hypothesize that all phenolic compounds are converted by Saccharomyces cerevisiae using the same metabolic process. We suggest that the enhancement of the ability of S. cerevisiae to convert toxic phenolic compounds into less inhibitory compounds is a potent route to developing a S. cerevisiae with superior tolerance to phenolic compounds.
|
|
| 5. |
- Agostini, Marco, 1987, et al.
(författare)
-
Free-Standing 3D-Sponged Nanofiber Electrodes for Ultrahigh-Rate Energy-Storage Devices
- 2018
-
Ingår i: ACS Applied Materials & Interfaces. - : American Chemical Society (ACS). - 1944-8252 .- 1944-8244. ; 10:40, s. 34140-34146
-
Tidskriftsartikel (refereegranskat)abstract
- We have designed a self-standing anode built-up from highly conductive 3D-sponged nanofibers, that is, with no current collectors, binders, or additional conductive agents. The small diameter of the fibers combined with an internal spongelike porosity results in short distances for lithium-ion diffusion and 3D pathways that facilitate the electronic conduction. Moreover, functional groups at the fiber surfaces lead to the formation of a stable solid-electrolyte interphase. We demonstrate that this anode enables the operation of Li-cells at specific currents as high as 20 A g-1 (approx. 50C) with excellent cycling stability and an energy density which is >50% higher than what is obtained with a commercial graphite anode.
|
|
| 6. |
- Ahlers, F.J., et al.
(författare)
-
The EMRP project GraphOhm- Towards quantum resistance metrology based on graphene
- 2014
-
Ingår i: CPEM Digest (Conference on Precision Electromagnetic Measurements). - 0589-1485. - 9781479952052 ; , s. 548-549, s. 548-549
-
Konferensbidrag (refereegranskat)abstract
- A new joint research project (JRP) integrating metrology institutes and universities from nine countries is aimed at realization of a new generation of standards for quantum resistance metrology. The project exploits graphene's properties to simplify operation of standards without compromising the unprecedented precision delivered by semiconductor quantum Hall devices. Higher operating temperatures (above 4.2 K, and up to 8 K) and together with lower magnetic fields (below 5 T, and potentially down to 2 T) will lead to a significantly improved and cost-saving dissemination of intrinsically referenced resistance standards to all end-users relying on electrical measurements.
|
|
| 7. |
- Ahlgren, Serina, et al.
(författare)
-
Climate and biodiversity impact of beef and lamb production – A case study in Sweden
- 2024
-
Ingår i: Agricultural Systems. - : Elsevier Ltd. - 1873-2267 .- 0308-521X. ; 219
-
Tidskriftsartikel (refereegranskat)abstract
- CONTEXT: The climate impact of meat production is a hotly debated topic. What is less often highlighted is that grazing ruminants can have positive impacts on biodiversity. OBJECTIVE: The aim of this study was to use a life cycle perspective to assess both the climate and biodiversity impact of different beef and lamb production systems in Sweden. METHODS: Applying a life cycle perspective, a quantitative method to assess biodiversity was used, with a scoring system based on land use. For the climate impact calculations, the ClimAg biophysical systems model was used, including emissions from drained organic soils and carbon sequestration in mineral soils. The functional unit was 1 kg carcass weight. RESULTS AND CONCLUSIONS: The results indicated large differences in biodiversity and climate impact between the production systems studied. Dairy bulls had relative low emissions of greenhouse gases, but also a low biodiversity score (a high score indicates higher level of biodiversity). Beef breed steers and heifers had higher emissions of greenhouse gases but a higher biodiversity score, suggesting a trade-off between climate and biodiversity impact. Also for lamb meat, greenhouse gas emissions vary among production systems. A system with winter born lambs slaughtered in spring, closely followed by spring born lambs slaughtered in autumn, had the lowest emissions, while spring born lambs slaughtered in winter had the highest emissions. Winter lambs on the other hand, had a relatively high biodiversity score, due to a long rearing period and an extensive land use with a high proportion of semi-natural grasslands. Climate impact was in all systems related to methane from enteric fermentation, emissions from manure storage, and emissions from organic soils. With the assumptions made in this study, soil carbon sequestration is suggested to reduce the climate impact by 5–7% of the total emissions. Biodiversity impact was in all systems positively related to the amount of grazing in permanent grasslands, in particular semi-natural grasslands. Because semi-natural grasslands are among the most species rich terrestrial ecosystems in Europe, a large surface area grazed resulted in high biodiversity scores in the present model. SIGNIFICANCE: This study used a novel approach for biodiversity assessment, where the positive contribution of semi-natural grasslands to biodiversity was quantified and put in relation to the modelled climate impact.
|
|
| 8. |
- Ahlgren, Serina, et al.
(författare)
-
Review of methodological choices in LCA of biorefinery systems - key issues and recommendations
- 2015
-
Ingår i: Biofuels, Bioproducts and Biorefining. - : Wiley. - 1932-1031 .- 1932-104X. ; 9:5, s. 606-619
-
Forskningsöversikt (refereegranskat)abstract
- The current trend in biomass conversion technologies is toward more efficient utilization of biomass feedstock in multiproduct biorefineries. Many life-cycle assessment (LCA) studies of biorefinery systems have been performed but differ in how they use the LCA methodology. Based on a review of existing LCA standards and guidelines, this paper provides recommendations on how to handle key methodological issues when performing LCA studies of biorefinery systems. Six key issues were identified: (i) goal definition, (ii) functional unit, (iii) allocation of biorefinery outputs, (iv) allocation of biomass feedstock, (v) land use, and (vi) biogenic carbon and timing of emissions. Many of the standards and guidelines reviewed here provide only general methodological recommendations. Some make more specific methodological recommendations, but these often differ between standards. In this paper we present some clarifications (e.g. examples of research questions and suitable functional units) and methodological recommendations (e.g. on allocation).
|
|
| 9. |
- Ahlinder, Astrid, et al.
(författare)
-
Development of a solid food simulant to evaluate migration of chemicals from paper and board food contact materials to moist food
- 2024
-
Ingår i: Food Packaging and Shelf Life. - : Elsevier Ltd. - 2214-2894. ; 45
-
Tidskriftsartikel (refereegranskat)abstract
- Food contact materials (FCMs) i.e. materials that food is packaged or handled in, must be safe for their intended use. European FCM legislation uses a risk-based approach, with a cornerstone of FCM's safety evaluation being measurement of migration of substances from FCMs to food simulants. The standard methods mainly developed for plastic FCMs are not always suitable for less inert and moisture sensitive materials such as paper and board. However, these are becoming increasingly common as FCMs e.g. to replace single-use plastics. In addition, there is a drive to further use recycled materials. To support this development, new methods for assessing the safety of these materials are needed. In the present feasibility study, a hydrogel crosslinked through freeze-thawing of poly(vinyl alcohol) was evaluated as a food simulant for moist foods. The migration of surrogate compounds from a spiked paperboard to the hydrogel was determined and compared to the migration to a real moist food (a slice of apple), the commonly used modified polyphenylene oxide (MPPO) and a water extract. Migration of polar surrogates to the hydrogel correlated well with the migration to the apple slice. However, our results indicate that the hydrogel is less suitable as simulant for non-polar surrogates. Overall, the study demonstrates the potential of this hydrogel-based simulant for improving risk assessment of less inert FCMs.
|
|
| 10. |
- Ahlström, Johan, 1990, et al.
(författare)
-
Economic potential for substitution of fossil fuels with liquefied biomethane in Swedish iron and steel industry – Synergy and competition with other sectors
- 2020
-
Ingår i: Energy Conversion and Management. - : Elsevier Ltd. - 0196-8904 .- 1879-2227. ; 209
-
Tidskriftsartikel (refereegranskat)abstract
- In Sweden, the iron and steel industry (ISI) is a major source of greenhouse gas (GHG) emissions. Most of the emissions result from the use of fossil reducing agents. Nevertheless, the use of fossil fuels for other purposes must also be eliminated in order to reach the Swedish emissions reduction targets. In this study, we investigate the possibility to replace fossil gaseous and liquid fuels used for heating in the ISI, with liquefied biomethane (LBG) produced through gasification of forest residues. We hypothesize that such utilization of fuels in the Swedish ISI is insufficient to independently drive the development of large-scale LBG production, and that other sectors demanding LBG, e.g., for transportation, can be expected to influence the economic potential for the ISI to switch to LBG. The paper investigates how demand for LBG from other sectors can contribute to, or prevent, a phase-out of fossil fuels used for heating purposes in the ISI under different future energy market scenarios, with additional analysis of the impact of a CO2 emissions charge. A geographically explicit cost-minimizing biofuel production localization model is combined with heat integration and energy market scenario analysis. The results show that from a set of possible future energy market scenarios, none yielded more than a 9% replacement of fossil fuels used for heating purposes in the ISI, and only when there was also a demand for LBG from other sectors. The scenarios corresponding to a more ambitious GHG mitigation policy did not achieve higher adoption of LBG, due to corresponding higher biomass prices. A CO2 charge exceeding 200 EUR/tonCO2 would be required to achieve a full phase-out of fossil fuels used for heating purposes in the ISI. We conclude that with the current policy situation, substitution of fossil fuels by LBG will not be economically feasible for the Swedish ISI.
|
|
