| 1. |
|
|
| 2. |
- Wannberg, Gudmund, et al.
(författare)
-
EISCAT_3D - a next-generation European radar system for upper atmosphere and geospace research
- 2010
-
Ingår i: Radio Science Bulletin. - 1024-4530. ; :333, s. 75-88
-
Tidskriftsartikel (refereegranskat)abstract
- The EISCAT Scientifi c Association, together with a number of collaborating institutions, has recently completed a feasibility and design study for an enhanced performance research radar facility to replace the existing EISCAT UHF and VHF systems. This study was supported by EU Sixth-Framework funding. The new radar retains the powerful multi-static geometry of the EISCAT UHF, but will employ phased arrays, direct-sampling receivers, and digital beamforming and beam steering. Design goals include, inter alia, a tenfold improvement in temporal and spatial resolution, an extension of the instantaneous measurement of full-vector ionospheric drift velocities from a single point to the entire altitude range of the radar, and an imaging capability to resolve small-scale structures. Prototype receivers and beamformers are currently being tested on a 48-element, 224 MHz array (the "Demonstrator") erected at the Kiruna EISCAT site, using the EISCAT VHF transmitter as an illuminator.
|
|
| 3. |
- Alrifaiy, Ahmed, et al.
(författare)
-
A lab-on-a-chip for hypoxic patch clamp measurements combined with optical tweezers and spectroscopy : first investigations of single biological cells
- 2015
-
Ingår i: Biomedical engineering online. - : Springer Science and Business Media LLC. - 1475-925X. ; 14
-
Tidskriftsartikel (refereegranskat)abstract
- The response and the reaction of the brain system to hypoxia is a vital research subject that requires special instrumentation. With this research subject in focus, a new multifunctional lab-on-a-chip (LOC) system with control over the oxygen content for studies on biological cells was developed. The chip was designed to incorporate the patch clamp technique, optical tweezers and absorption spectroscopy. The performance of the LOC was tested by a series of experiments. The oxygen content within the channels of the LOC was monitored by an oxygen sensor and verified by simultaneously studying the oxygenation state of chicken red blood cells (RBCs) with absorption spectra. The chicken RBCs were manipulated optically and steered in three dimensions towards a patch-clamp micropipette in a closed microfluidic channel. The oxygen level within the channels could be changed from a normoxic value of 18% O 2 to an anoxic value of 0.0-0.5% O 2. A time series of 3 experiments were performed, showing that the spectral transfer from the oxygenated to the deoxygenated state occurred after about 227 ± 1 s and a fully developed deoxygenated spectrum was observed after 298 ± 1 s, a mean value of 3 experiments. The tightness of the chamber to oxygen diffusion was verified by stopping the flow into the channel system while continuously recording absorption spectra showing an unchanged deoxygenated state during 5400 ± 2 s. A transfer of the oxygenated absorption spectra was achieved after 426 ± 1 s when exposing the cell to normoxic buffer. This showed the long time viability of the investigated cells. Successful patching and sealing were established on a trapped RBC and the whole-cell access (Ra) and membrane (Rm) resistances were measured to be 5.033 ± 0.412 M Ω and 889.7 ± 1.74 M Ω respectively.
|
|
| 4. |
- Gabert, A., et al.
(författare)
-
Temperature stabilization of electronics module
- 2006
-
Ingår i: The IMAPS Nordic Annual Conference. - Oslo : International Microelectronics and Packaging Society (IMAPS) Nordic. - 9519800298 ; , s. 97-103
-
Konferensbidrag (refereegranskat)abstract
- Outdoor applications of electronics modules expose the systems to harsh environmental conditions. When very high performance is required, it may be necessary to actively stabilize the temperature in the module. This paper presents a systematic approach to the problem of designing a temperature stabilized environment for medium size electronics modules. The target system is the front-end electronics for the antennas in the EISCAT-3D incoherent scatter radar system. The electronics have an estimated constant power dissipation of about 10 W. Initially simulations verified the design approach and gave valuable information of the heat distribution in the box over the range of target temperatures. The design was evaluated by making a prototype on which different measurements were performed, which gave a clear picture of the system functionality. Using two Peltier modules and an insulated box a temperature stability of ±0.02°C at 20°C over an ambient temperature range of -40°C to 40°C was achieved.
|
|
