| 1. |
- Enmark, Markus, 1991, et al.
(författare)
-
A Critical Assessment of Nano Enhanced Vapor Chamber Wick Structures for Electronics Cooling
- 2021
-
Ingår i: 2021 23rd European Microelectronics and Packaging Conference and Exhibition, EMPC 2021.
-
Konferensbidrag (refereegranskat)abstract
- The increasing need for high thermal dissipation in small electronic products puts tough requirements on effective cooling solutions. Two of the most effective passive cooling devices in electronics today are vapor chambers and heat pipes. With new advancements in materials science and nanotechnology comes the possibility to further increase cooling capacity and at the same time make devices lighter. This study is a critical assessment on recent progress in the field of nanomaterial enhanced wick structures in vapor chambers and heat pipes. In this paper, nano-enhanced wick structures are divided into five different sub-categories based on material type. Publication trends for the different types of nano-enhanced wicks are studied by plotting them on a timeline. It is found that nanostructured metal wicks is the most studied field in recent years. A plot showing wick performance in terms of superheat temperatures for given heat flux is created to be used for benchmarking of new wick structures when pool boil experiments are carried out. An attempt to find correlation between publication trends, type of wick and performance is done. On the basis of the gathered data it is deemed difficult to find a distinct correlation, this is mainly due to difficulty in comparing performance between different studies, especially when different heat fluxes are used. There is no unambiguous answer to which category of nano-enhanced wicks that should be target for future studies. Graphene coating and pure carbon nanomaterials such as aerogels and graphene foam are still relatively unexplored and believed to have great potential if they can be attached to envelope materials.
|
|
| 2. |
- Hansson, Josef, 1991, et al.
(författare)
-
Effects of high temperature treatment of carbon nanotube arrays on graphite : Increased crystallinity, anchoring and inter-tube bonding
- 2020
-
Ingår i: Nanotechnology. - : Institute of Physics Publishing (IOPP). - 0957-4484 .- 1361-6528. ; 31:45
-
Tidskriftsartikel (refereegranskat)abstract
- Thermal treatment of carbon nanotubes (CNTs) can significantly improve their mechanical, electrical and thermal properties due to reduced defects and increased crystallinity. In this work we investigate the effect of annealing at 3000 degrees C of vertically aligned CNT arrays synthesized by chemical vapor deposition (CVD) on graphite. Raman measurements show a drastically reduced amount of defects and, together with transmission electron microscope (TEM) diffraction measurements, an increased average crystallite size of around 50%, which corresponds to a 124% increase in Young's modulus. We also find a tendency for CNTs to bond to each other with van der Waals (vdW) forces, which causes individual CNTs to closely align with each other. This bonding causes a densification effect on the entire CNT array, which appears at temperatures >1000 degrees C. The densification onset temperature corresponds to the thermal decomposition of oxygen containing functional groups, which otherwise prevents close enough contact for vdW bonding. Finally, the remaining CVD catalyst on the bottom of the CNT array is evaporated during annealing, enabling direct anchoring of the CNTs to the underlying graphite substrate.
|
|
| 3. |
- Kabiri Samani, Majid, 1976, et al.
(författare)
-
Improving Thermal Transport at Carbon Hybrid Interfaces by Covalent Bonds
- 2018
-
Ingår i: Advanced Materials Interfaces. - : Wiley. - 2196-7350. ; 5:15
-
Tidskriftsartikel (refereegranskat)abstract
- Graphene and carbon nanotubes have received much attention for thermal management application due to their unique thermal performance. Theoretical work suggests that a covalent bond can combine 1D carbon nanotubes with 2D graphene together to extend the excellent thermal property to three dimensions for heat dissipation. This paper experimentally demonstrates the high heat dissipation capability of a freestanding 3D multiwall carbon nanotube (MWCNT) and graphene hybrid material. Using high-resolution transmission electron microscopy and pulsed photothermal reflection measurement method, the covalent bonds between MWCNT and planar graphene are microscopically and numerically demonstrated. Thermal resistance at the junction with covalent bonds is 9×10^−10 Kelvin square meter per watt, which is three orders of magnitude lower than van der Waals contact. Joule heating method is used to verify the extra cooling effect of this 3D hybrid material compared to graphite film. A demonstrator using high power chip is developed to demonstrate the applicability of this hybrid material in thermal application. Temperature at hot spots can be decreased by around 10°C with the assistance of this hybrid material. These findings are very significant for understanding the thermal conduction during combining 1D and 2D carbon material together for future thermal management application.
|
|
| 4. |
- Nylander, Andreas, 1988, et al.
(författare)
-
Degradation of Carbon Nanotube Array Thermal Interface Materials through Thermal Aging: Effects of Bonding, Array Height, and Catalyst Oxidation
- 2021
-
Ingår i: ACS Applied Materials & Interfaces. - : American Chemical Society (ACS). - 1944-8252 .- 1944-8244. ; 13:26, s. 30992-31000
-
Tidskriftsartikel (refereegranskat)abstract
- Carbon nanotube (CNT) array thermal interface materials (TIMs) are promising candidates for high-performance applications in terms of thermal performance. However, in order to be useful in commercial applications, the reliability of the interfaces is an equally important parameter, which so far has not been thoroughly investigated. In this study, the reliability of CNT array TIMs is investigated through accelerated aging. The roles of CNT array height and substrate configuration are studied for their relative impact on thermal resistance degradation. After aging, the CNT catalyst is analyzed using X-ray photoelectron spectroscopy to evaluate chemical changes. The CNT-catalyst bond appears to degrade during aging but not to the extent that the TIM performance is compromised. On the other hand, coefficient of thermal expansion mismatch between surfaces creates strain that needs to be absorbed, which requires CNT arrays with sufficient height. Transfer and bonding of both CNT roots and tips also create more reliable interfaces. Crucially, we find that the CNT array height of most previously reported CNT array TIMs is not enough to prevent significant reliability problems.
|
|
| 5. |
- Zehri, Abdelhafid, 1989, et al.
(författare)
-
Exploring Graphene Coated Copper Nanoparticles as a multifunctional Nanofiller for Micro-Scaled Copper Paste
- 2021
-
Ingår i: 2021 23rd European Microelectronics and Packaging Conference and Exhibition, EMPC 2021.
-
Konferensbidrag (refereegranskat)abstract
- The current development of the electronics system requires capabilities beyond conventional heat transfer approaches. New solutions based on advanced materials are being developed to tackle the current challenges in the development of electronics systems and the nanoscale 2D materials such as graphene are at the centre of the effort to exploit the intrinsic properties of carbon nanomaterials. In this work, we introduce a new concept of graphene-coated copper nanoparticles (G-CuNPs) and explore their multifunctional potential applications in metallic based paste used in electronics. The nanoscale powder was found to present a core/shell structure with the copper particle at its core and a disordered multilayer graphene structure continuously coating its surface. The composition of the particles was analysed, and the presence of the coating was found to provide oxidation protection for the metallic core. Thermogravimetric analysis (TGA) showed an additional role of the G-CuNPs with a reduction effect without the use of an additional reducing agent. Furthermore, due to the combined effect of the size of the particles and the oxidation-free metallic core, Differential Scanning Calorimetry (DSC) analysis revealed a melting depression at temperatures as low as 155 °C. Finally, the mechanical properties of the nanocoating were investigated and the results showed an enhanced ductility at the surface of the particles due to the presence of the multi-layered graphene structure, which might be exploited for powder flow and lubrication effect.
|
|
| 6. |
- Zehri, Abdelhafid, 1989, et al.
(författare)
-
Graphene Oxide and Nitrogen-Doped Graphene Coated Copper Nanoparticles in Water-Based Nanofluids for Thermal Management in Electronics
- 2022
-
Ingår i: JOURNAL OF NANOFLUIDS. - : American Scientific Publishers. - 2169-432X .- 2169-4338. ; 11:1, s. 125-134
-
Tidskriftsartikel (refereegranskat)abstract
- Graphene oxide (GO) and nitrogen-doped graphene (NG) coated copper nanoparticles (NPs) have been developed in this work and investigated as nanofiller for water as Heat Transfer Fluids (HTFs). The morphology and composition of the coating were characterized to confirm the presence of functional groups and the nitrogen-doping of the graphene coating. Different fractions of the two types of coated nanoparticles NPs between 0.1 and 10 wt.% were dispersed in water. The thermal conductivity of the dispersions was evaluated at temperatures between 20 and 50 degrees C. A positive correlation between the thermal conductivity of the HTFs and the fraction and temperature are observed as a result of the increase of the solid phase contribution into the heat transfer. At a concentration of 0.5 wt.%, the thermal conductivity of the NG-CuNPs nanofluid reached its maximum increase of 78%, compared to a 13% increase in the case of GO-CuNPs. However, due to the poor stability of the NG-CuNPs, further increase of the solid phase did not result in any additional improvement. In contrast, the thermal conductivity of the GO-based dispersion resulted in a 103% enhancement at 10 wt.% at a temperature of 50 degrees C.
|
|
| 7. |
- Zehri, Abdelhafid, 1989, et al.
(författare)
-
High porosity and light weight graphene foam heat sink and phase change material container for thermal management
- 2020
-
Ingår i: Nanotechnology. - : IOP Publishing. - 1361-6528 .- 0957-4484. ; 31:42
-
Tidskriftsartikel (refereegranskat)abstract
- During the last decade, graphene foam emerged as a promising high porosity 3-dimensional (3D) structure for various applications. More specifically, it has attracted significant interest as a solution for thermal management in electronics. In this study, we investigate the possibility to use such porous materials as a heat sink and a container for a phase change material (PCM). Graphene foam (GF) was produced using chemical vapor deposition (CVD) process and attached to a thermal test chip using sintered silver nanoparticles (Ag NPs). The thermal conductivity of the graphene foam reached 1.3 W m(-1)K(-1), while the addition of Ag as a graphene foam silver composite (GF/Ag) enhanced further its effective thermal conductivity by 54%. Comparatively to nickel foam, GF and GF/Ag showed lower junction temperatures thanks to higher effective thermal conductivity and a better contact. A finite element model was developed to simulate the fluid flow through the foam structure model and showed a positive and a non-negligible contributions of the secondary microchannel within the graphene foam. A ratio of 15 times was found between the convective heat flux within the primary and secondary microchannel. Our paper successfully demonstrates the possibility of using such 3D porous material as a PCM container and heat sink and highlight the advantage of using the carbon-based high porosity material to take advantage of its additional secondary porosity.
|
|
