SwePub
Sök i SwePub databas

  Utökad sökning

Träfflista för sökning "WFRF:(Ghaderi M) ;pers:(Enoksson Peter 1957)"

Sökning: WFRF:(Ghaderi M) > Enoksson Peter 1957

  • Resultat 1-6 av 6
Sortera/gruppera träfflistan
   
NumreringReferensOmslagsbildHitta
1.
  • Ayerden, N.P., et al. (författare)
  • Design, fabrication and characterization of LVOF-based IR microspectrometers
  • 2014
  • Ingår i: Proceedings of SPIE - The International Society for Optical Engineering. - : SPIE. - 0277-786X .- 1996-756X. - 9781628410785 ; 9130
  • Konferensbidrag (refereegranskat)abstract
    • This paper presents the design, fabrication and characterization of a linear variable optical filter (LVOF) that operates in the infrared (IR) spectral range. An LVOF-based microspectrometer is a tapered-cavity Fabry-Perot optical filter placed on top of a linear array of detectors. The filter transforms the optical spectrum into a lateral intensity profile, which is recorded by the detectors. The IR LVOF has been fabricated in an IC-compatible process flow using a resist reflow and is followed by the transfer etching of this resist pattern into the optical resonator layer. This technique provides the possibility to fabricate a small, robust and high-resolution micro-spectrometer in the IR spectral range directly on a detector chip. In these designs, the LVOF uses thin-film layers of sputtered Si and SiO 2 as the high and low refractive index materials respectively. By tuning the deposition conditions and analyzing the optical properties with a commercial ellipsometer, the refractive index for Si and SiO2 thin-films was measured and optimized for the intended spectral range. Two LVOF microspectrometers, one operating in the 1.8-2.8 μm, and the other in the 3.0-4.5 μm wavelength range, have been designed and fabricated on a silicon wafer. The filters consist of a Fabry-Perot structure combined with a band-pass filter to block the out-of-band transmission. Finally, the filters were fully characterized with an FTIR spectrometer and the transmission curve widening was investigated. The measured transmittance curves were in agreement with theory. The characterization shows a spectral resolution of 35-60 nm for the short wavelength range LVOF and 70 nm for the long wavelength range LVOF, which can be further improved using signal processing algorithms.
  •  
2.
  • Ayerden, N.P., et al. (författare)
  • A miniaturized optical gas-composition sensor with integrated sample chamber
  • 2016
  • Ingår i: Sensors and Actuators, B: Chemical. - : Elsevier BV. - 0925-4005. ; 236:29, s. 917-925
  • Tidskriftsartikel (refereegranskat)abstract
    • A robust and highly miniaturized optical gas sensor based on optical absorption spectroscopy is presented. By using the resonator cavity of a linear variable optical filter (LVOF) also as a gas chamber, a compact and robust optical sensor is achieved. The device operates at the 15th order in 3.2–3.4 μm wavelength range for distinguishing hydrocarbons. The physical cavity length at the μm-level is translated into an effective optical absorption path length at the mm-level by the use of highly reflective (R > 98%) Bragg mirrors. The optical design using the Fizeau interferometer approach is described. Moreover, the CMOS-compatible fabrication method is explained. In addition to the wideband and single wavelength filter characterization, absorption of methane in the LVOF cavity is demonstrated at 3392 nm and 3416.60 nm wavelengths.
  •  
3.
  • Ghaderi, M., et al. (författare)
  • Design, fabrication and characterization of infrared LVOFs for measuring gas composition
  • 2014
  • Ingår i: Journal of Micromechanics and Microengineering. - : IOP Publishing. - 1361-6439 .- 0960-1317. ; 24:8, s. Art. no. 084001-
  • Tidskriftsartikel (refereegranskat)abstract
    • This paper presents the design, fabrication and characterization of a linear-variable optical-filter (LVOF) that will be used in a micro-spectrometer operating in infrared (IR) for natural gas composition measurement. An LVOF is placed on top of an array of detectors and transforms the optical spectrum into a lateral intensity profile, which is recorded by the detectors. The IR LVOF was fabricated in an IC-compatible process using a photoresist reflow technique, followed by transfer etching of the photoresist into the optical resonator layer. The spectral range between 3 to 5 mu m contains the absorption peaks for hydrocarbons, carbon-monoxide and carbon-dioxide. The resulting optical absorption is utilized to measure the gas concentrations in a sample volume. Two LVOF structures were designed and fabricated on silicon wafers using alternate layers of sputtered silicon and silicon-dioxide as the high- and low- refractive index materials. These filters consist of a Fabry-Perot resonator combined with a band-pass filter designed to block out-of-band transmissions. Finally, the filters were fully characterized with an FTIR spectrometer and showed satisfactory agreement with the optical thin-film simulations. The characterization showed a spectral resolution of 100 nm, which can be further improved with signal processing algorithms. This method makes it possible to fabricate small and robust LVOFs with high resolving power in the IR spectral range directly on the detector array chip.
  •  
4.
  • Ghaderi, Mohammadamir, 1986, et al. (författare)
  • Self-Cleaning Micro-Windows for In-Tailpipe Optical Exhaust Gas Measurements
  • 2020
  • Ingår i: IEEE International Symposium on Industrial Electronics. ; 2020-June, s. 1104-1108
  • Konferensbidrag (refereegranskat)abstract
    • Exhaust gas measurement in the harsh environment of the tailpipe of a combustion engine by optical techniques is a highly robust technique, provided that optical access is maintained in the presence of particulate matter (PM). The considerations are presented for the systematic design of membranes with integrated heaters in SiC-on-Si technology for generating a well-defined lateral temperature profile with peak temperatures above 600 °C. Periodically raising the temperature of the membranes to such a level is demonstrated to keep the surface transparent by oxidation of soot deposits. This paper is about continuous heating of the membrane to a temperature slightly higher than that of the exhaust gas. At such temperatures thermophoretic repulsion of PM allows allows long-term optical measurement in the exhaust without the thermo-mechanical loading by repetitive thermal cycling.
  •  
5.
  • Ghaderi, Mohammadamir, 1986, et al. (författare)
  • Thermally regenerable optical transparent MEMS windows for exhaust gas analysis
  • 2020
  • Ingår i: Optics InfoBase Conference Papers.
  • Konferensbidrag (refereegranskat)abstract
    • Exhaust gas measurement in the harsh environment of the tailpipe by optical techniques is a highly robust technique, provided that optical access is maintained in the presence of soot. The design, fabrication, and testing of membranes in SiC-on-Si with integrated heaters to serve as a regenerable MEMS optical window into the tailpipe are presented. Membranes at slightly elevated temperatures are demonstrated to keep the surface transparent by thermophoresis, while surface regeneration is achieved at pulsed high temperatures, which allows long-term optical measurement in the exhaust.
  •  
6.
  • Middelburg, Luke M., et al. (författare)
  • Maintaining transparency of a heated MEMs membrane for enabling long-term optical measurements on soot-containing exhaust gas
  • 2020
  • Ingår i: Sensors. - : MDPI AG. - 1424-8220. ; 20:1
  • Tidskriftsartikel (refereegranskat)abstract
    • Ensuring optical transparency over a wide spectral range of a window with a view into the tailpipe of the combustion engine, while it is exposed to the harsh environment of sootcontaining exhaust gas, is an essential pre-requisite for introducing optical techniques for long-term monitoring of automotive emissions. Therefore, a regenerable window composed of an optically transparent polysilicon-carbide membrane with a diameter ranging from 100 µm up to 2000 µm has been fabricated in microelectromechanical systems (MEMS) technology. In the first operating mode, window transparency is periodically restored by pulsed heating of the membrane using an integrated resistor for heating to temperatures that result in oxidation of deposited soot (600–700 °C). In the second mode, the membrane is kept transparent by repelling soot particles using thermophoresis. The same integrated resistor is used to yield a temperature gradient by continuous moderate-temperature heating. Realized devices have been subjected to laboratory soot exposure experiments. Membrane temperatures exceeding 500 °C have been achieved without damage to the membrane. Moreover, heating of membranes to ΔT = 40 °C above gas temperature provides sufficient thermophoretic repulsion to prevent particle deposition and maintain transparency at high soot exposure, while non-heated identical membranes on the same die and at the same exposure are heavily contaminated.
  •  
Skapa referenser, mejla, bekava och länka
  • Resultat 1-6 av 6

Kungliga biblioteket hanterar dina personuppgifter i enlighet med EU:s dataskyddsförordning (2018), GDPR. Läs mer om hur det funkar här.
Så här hanterar KB dina uppgifter vid användning av denna tjänst.

 
pil uppåt Stäng

Kopiera och spara länken för att återkomma till aktuell vy