| 1. |
- Chen, Shujing, et al.
(författare)
-
Scalable production of thick graphene films for next generation thermal management applications
- 2020
-
Ingår i: Carbon. - : Elsevier BV. - 0008-6223. ; 167, s. 270-277
-
Tidskriftsartikel (refereegranskat)abstract
- With the increasing demand on integration and better performance of portable electronics devices, the system operation temperatures are expected to continue to increase, leading eventually to degeneration in functional performance and reliability. Therefore, demand for thermal management materials that effectively spread heat and reduce heat density is urgent. The existing solution of pyrolytic graphite film (PGF) is unsatisfactory due to their low heat flux carrying capacity or low thermal conductivity, as well as poor mechanical performance. This work solves the problem by substituting ultra-thick (>75 mm) graphene film (GF) for PGF, offering more than three times higher heat flux carrying capacity. The conjugation of large crystallinity and firm structures endows GFs with excellent thermal conductive performance (up to 1204 +/- 35 W m(-1) K-1), great heat flux carrying capacity, and good foldability (5000 cycles folding). In addition to this, such a GF is produced based on an economically efficient and quasi industrial method incorporating continuous high-pressure homogenization processing (HPH), indicating an enormous potential as a new pathway to thermal management applications.
|
|
| 2. |
- Bao, Jie, et al.
(författare)
-
Application of two-dimensional layered hexagonal boron nitride in chip cooling
- 2016
-
Ingår i: Yingyong Jichu yu Gongcheng Kexue Xuebao/Journal of Basic Science and Engineering. - 1005-0930. ; 24:1, s. 210-217
-
Tidskriftsartikel (refereegranskat)abstract
- © 2016, The Editorial Board of Journal of Basic Science and Engineering. All right reserved.Research into layered hexagonal boron nitride(h-BN)has recently intensified, due to its superior physicochemical properties compared to that of a typical two-dimensional material. H-BN can be utilized in power chips as both an insulating layer as well as a heat spreader for local hotspots with high heat flux. Single layer h-BN film grown by CVD and h-BN microparticles are respectively transferred onto the surfaces of the thermal evaluation chips, where the influence of h-BN on the heat dissipation performance of the chips can be observed at different power values. The resistance-temperature curve method and infrared thermal imager are both used to measure the temperature of hotspots on the thermal evaluation chips, which can be reduced by between 3~5℃ at 1W after the transfer of h-BN. The cooling efficiency is improved and it can be found that single layer h-BN film shows better heat dissipation ability.
|
|
| 3. |
- Bao, Jie, 1982, et al.
(författare)
-
Two-dimensional hexagonal boron nitride as lateral heat spreader in electrically insulating packaging
- 2016
-
Ingår i: Journal of Physics D: Applied Physics. - : IOP Publishing. - 1361-6463 .- 0022-3727. ; 49:July 2016, s. 265501-
-
Tidskriftsartikel (refereegranskat)abstract
- The need for electrically insulating materials with a high in-plane thermal conductivity for lateral heat spreading applications in electronic devices has intensified studies of layered hexagonal boron nitride (h-BN) films. Due to its physicochemical properties, h-BN can be utilised in power dissipating devices such as an electrically insulating heat spreader material for laterally redistributing the heat from hotspots caused by locally excessive heat flux densities. In this study, two types of boron nitride based heat spreader test structures have been assembled and evaluated for heat dissipation. The test structures separately utilised a few-layer h-BN film with and without graphene enhancement drop coated onto the hotspot test structure. The influence of the h-BN heat spreader films on the temperature distribution across the surface of the hotspot test structure was studied at a range of heat flux densities through the hotspot. It was found that the graphene-enhanced h-BN film reduced the hotspot temperature by about 8–10°C at a 1000 W/cm2 heat flux density, a temperature decrease significantly larger than for h-BN film without graphene enhancement. Finite element simulations of the h-BN film predict that further improvements in heat spreading ability are possible if the thermal contact resistance between the film and test chip are minimised.
|
|
| 4. |
- Huang, S., et al.
(författare)
-
Improved reliability of electrically conductive adhesives joints on Cu-Plated PCB substrate enhanced by graphene protection barrier
- 2017
-
Ingår i: 2017 IMAPS Nordic Conference on Microelectronics Packaging, NordPac 2017, Goteborg, Sweden, 18-20 June 2017. - 9781538630556 ; , s. 143-146
-
Konferensbidrag (refereegranskat)abstract
- Graphene protection barrier was introduced to the interface between the ECAs and Cu-plated wire to enhance the reliability of the ECAs joints on Cu-Plated PCB substrate due to its excellent properties of impermeability to all gases/salts as well as its thermal/chemical stability. The results of shear test indicated graphene protection barrier can improve the shear strength of the ECAs joints on Cu-plated PCB substrate by almost 22% after 500 hours high temperature and high humidity cyclic test. Characterizations by optical microscope and XPS were further performed to explain the mechanism. To sum up, it can be believed that the graphene protection barrier can dramatically enhance the reliability of the ECAs joints on Cu-Plated PCB substrate.
|
|
| 5. |
- Huang, Shirong, et al.
(författare)
-
Infrared Emissivity Measurement for Vertically Aligned Multiwall Carbon Nanotubes (CNTs) Based Heat Spreader Applied in High Power Electronics Packaging
- 2016
-
Ingår i: 6th Electronic System-integration Technology Conference (ESTC 2016). - 9781509014026 ; , s. Article no 7764696-
-
Konferensbidrag (refereegranskat)abstract
- Vertically-aligned multiwall carbon nanotubes were deposited on silicon substrate by low pressure chemical vapor deposition (LPCVD), which can be utilized as heat spreaders in high power electronic packaging due to their remarkable thermal conductivity. The infrared emissivity of the vertically aligned multiwall carbon nanotubes was then characterized based on the FLIR SC600 infrared imaging system. The average infrared emissivity of the multiwall carbon nanotubes sample was about 0.92, which agrees well with experimental results reported before. Scanning electron microscopy (SEM) images of the multiwall carbon nanotubes were further analyzed to explain its high emissivity, and the reason can be attributed to the homogeneous sparseness and aligned structure of the vertically aligned multiwall carbon nanotubes
|
|
| 6. |
- Huang, Shirong, et al.
(författare)
-
The Effects of Graphene-Based Films as Heat Spreaders for Thermal Management in Electronic Packaging
- 2016
-
Ingår i: 2016 17th International Conference on Electronic Packaging Technology, ICEPT 2016. - 9781509013968 ; , s. Art no 7583272; Pages 889-892
-
Konferensbidrag (refereegranskat)abstract
- Graphene-based films (GBF) were fabricated using a chemical conversion process including graphene oxide (GO) preparation by use of Hummer’s method, graphene oxide reduction using L-ascorbic acid (LAA), and finally film formation by vacuum filtration. GBF is considered as a candidate material for thermal management, i.e. for removing heat from hotspots in power electronic packaging, due to its high thermal conductivity. In this work, the GBF heat spreading performance in 3D TSV packaging was analysed using finite element methods (FEM) implemented in the COMSOL software. Both size effects and the influence of the thermal conductivity of the GBF heat spreader on the thermal performance of the 3D TSV package were evaluated. Furthermore, the size effects of the thermal conductive adhesive (TCA) underfill between the chip and the printed circuit board (PCB) were analysed. The results obtained are critical for proper design of graphene-based lateral heat spreaders in high power electronic packaging.
|
|
| 7. |
- Jeppson, Kjell, 1947, et al.
(författare)
-
Hotspot test structures for evaluating carbon nanotube microfin coolers and graphene-like heat spreaders
- 2016
-
Ingår i: 29th IEEE International Conference on Microelectronic Test Structures (ICMTS), Yokohama, Japan, Mar 28-31, 2016. - 1071-9032. ; , s. 32-36
-
Konferensbidrag (refereegranskat)abstract
- The design, fabrication, and use of a hotspot-producing and temperature-sensing test structure for evaluating the thermal properties of carbon nanotubes, graphene and boron nitride for cooling of electronic devices in applications like 3D integrated chip-stacks, power amplifiers and light-emitting diodes is described. The test structure is a simple meander-shaped metal resistor serving both as the hotspot and the temperature thermo-meter. By use of this test structure, the influence of emerging materials like those mentioned above on the temperature of the hotspot has been evaluated with good accuracy).
|
|
| 8. |
- Wang, Nan, 1988, et al.
(författare)
-
Tailoring the Thermal and Mechanical Properties of Graphene Film by Structural Engineering
- 2018
-
Ingår i: Small. - : Wiley. - 1613-6810 .- 1613-6829. ; 14:29
-
Tidskriftsartikel (refereegranskat)abstract
- Due to substantial phonon scattering induced by various structural defects, the in-plane thermal conductivity (K) of graphene films (GFs) is still inferior to the commercial pyrolytic graphite sheet (PGS). Here, the problem is solved by engineering the structures of GFs in the aspects of grain size, film alignment, and thickness, and interlayer binding energy. The maximum K of GFs reaches to 3200 W m−1K−1and outperforms PGS by 60%. The superior K of GFs is strongly related to its large and intact grains, which are over four times larger than the best PGS. The large smooth features about 11 µm and good layer alignment of GFs also benefit on reducing phonon scattering induced by wrinkles/defects. In addition, the presence of substantial turbostratic-stacking graphene is found up to 37% in thin GFs. The lacking of order in turbostratic-stacking graphene leads to very weak interlayer binding energy, which can significantly decrease the phonon interfacial scattering. The GFs also demonstrate excellent flexibility and high tensile strength, which is about three times higher than PGS. Therefore, GFs with optimized structures and properties show great potentials in thermal management of form-factor-driven electronics and other high-power-driven systems.
|
|
| 9. |
- Yang, Y., et al.
(författare)
-
Heat dissipation performance of graphene enhanced electrically conductive adhesive for electronic packaging
- 2017
-
Ingår i: 2017 IMAPS Nordic Conference on Microelectronics Packaging, NordPac 2017, Goteborg, Sweden, 18-20 June 2017. - 9781538630556 ; , s. 125-128
-
Konferensbidrag (refereegranskat)abstract
- Electrically conductive adhesive is a new type of environmentally interconnect material which can be used in electronic packaging to replace the traditional solders due to its advantages of simple applying process and low curing temperature. Silver coated graphene is employed in this work to enhance the thermal conductivity of the current commercial electrically conductive adhesive with very low thermal conductivity. Thermal conductivity of the electrically conductive adhesive was measured by laser flash thermal analyzer. The infrared thermal imager was utilized to obtain the temperature distribution of chip surface. The results indicated that the developed graphene enhanced electrically conductive adhesive has perfect heat performances. It can be believed that this new kind of electrically conductive adhesive possesses promising application in electronic packaging in the future.
|
|
| 10. |
- Yuan, G., et al.
(författare)
-
Graphene-based heat spreading materials for electronics packaging applications
- 2017
-
Ingår i: 2017 IMAPS Nordic Conference on Microelectronics Packaging, NordPac 2017, Goteborg, Sweden, 18-20 June 2017. - 9781538630556 ; , s. 172-174
-
Konferensbidrag (refereegranskat)abstract
- Graphene-based heat spreading materials, including graphene-based film (GBF) and graphene-based electrically conductive adhesive (G-CA), were applied to electronics packaging. The thermal performances of GBF and G-CA were analyzed by resistance temperature detector (RTD) and thermal infrared imager. When the chip was covered by GBF and G-CA, the temperature of hotspot could be reduced by 3.1°C, at heat flux of 580 W/cm2. To analyze the thermal performances of G-CA and GBF in 3D electronics packaging, the distribution of temperature and temperature profiles on the top surface of chip were analyzed by COMSOL. Both of GBF and G-CA could obviously reduce the temperature of hotspot on the top surface of chip, compared with that on the bare chip. With G-CA and GBF, the temperature of hotspot could be reduced by 8°C. It suggests that both of G-CA and GBF are good heat spreading materials for electronics packaging application.
|
|
