| 1. |
- Davidsson, Kent, 1967, et al.
(författare)
-
Potassium, chlorine, and sulfur in ash, particles, deposits, and corrosion during wood combustion in a circulating fluidized-bed boiler
- 2007
-
Ingår i: Energy & Fuels. - : American Chemical Society (ACS). - 1520-5029 .- 0887-0624. ; 21:1, s. 71-81
-
Tidskriftsartikel (refereegranskat)abstract
- The effect of the addition of chlorine and/or sulfur to the fuel on fly ash composition, deposit formation, and superheater corrosion has been studied during biomass combustion in a circulating fluidized-bed boiler. The chlorine (HCl (aq)) and sulfur (SO2 (g)) were added in proportions of relevance for the potassium chemistry. The composition of the bottom and the fly ashes was analyzed. Gas and particle measurements were performed downstream of the cyclone before the convection pass and the flue gas composition was recorded in the stack with a series of standard instruments and an FTIR analyzer. At the position downstream of the cyclone, a deposit probe was situated, simulating a superheater tube. Deposits on the probe and initial corrosion were examined. It is concluded that addition of sulfur and chlorine increases the formation of submicron particles leading to deposition of potassium sulfate and chloride. The results compare well with earlier work based on laboratory-scale experiments concerning effects of chlorine and sulfur on potassium chemistry.
|
|
| 2. |
- Froitzheim, Jan, 1981, et al.
(författare)
-
Chromium evaporation of Coated and uncoated FE-22CR steels investigated by a novel denuder technique
- 2009
-
Ingår i: 3rd European Fuel Cell Technology and Applications - Piero Lunghi Conference, EFC 2009; Rome; Italy; 15 December 2009 through 18 December 2009. - 9788882862114 ; , s. 77-78
-
Konferensbidrag (refereegranskat)abstract
- The formation of volatile chromium species is a major problem concerning metallic interconnects for Solid Oxide Fuel Cells (SOFC). This problem is known and a number of routes, usually in the form of coatings, has been presented to overcome this problem. This paper investigates the influence of thin metallic films which can be applied by a low cost process. The measurements are carried out by a novel denuder technique where volatile chromium species are collected as sodium chromate. This technique allows the quantification of chromium evaporation in a time resolved manner. Coated and uncoated samples of ferritic steels developed for SOFC applications are investigated at 850°C in a N2-O2-H2O environment.
|
|
| 3. |
- Froitzheim, Jan, 1981, et al.
(författare)
-
Cr evaporation of metallic interconnects: A novel method for quantification
- 2009
-
Ingår i: ECS Transactions. - : The Electrochemical Society. - 1938-5862 .- 1938-6737. - 9781566777391 ; 25:2 PART 2, s. 1423-1428
-
Konferensbidrag (refereegranskat)abstract
- Chromium evaporation from metallic interconnects in SOFCs is commonly poisoning the cathode of SOFCs. To reduce chromium evaporation, rather thick coatings have been deposited using various coating techniques. In this study, a 22% Cr ferritic steel has been coated with thin films (
|
|
| 4. |
- Froitzheim, Jan, 1981, et al.
(författare)
-
Investigation of Chromium Volatilization from FeCr Interconnects by a Denuder Technique
- 2010
-
Ingår i: Journal of the Electrochemical Society. - : The Electrochemical Society. - 1945-7111 .- 0013-4651. ; 157:9, s. B1295-B1300
-
Tidskriftsartikel (refereegranskat)abstract
- A technique is presented for accurate and time-resolved quantification of chromium volatilization from alloys at high temperature. A denuder tube which is coated with Na2CO3 is placed downstream of the samples. CrO2(OH)(2) that evaporated from the samples is collected on the denuder and converted to the thermally stable Na2CrO4. The chromate is then dissolved in water and determined quantitatively. Three commercially available ferritic 22% Cr steels intended for use as solid oxide fuel cell interconnect materials (Sanergy HT, Crofer 22 APU, and ZMG 232) have been investigated with respect to chromium volatilization and oxidation rate. The effect on chromium volatilization of a submicrometer cobalt coating on the steel surface is reported. Comparisons are made with a conventional thick ceramic coating. The experiments are carried out at 850 degrees C in N-2 - 20% O-2 - 3% H2O atmosphere. The submicrometer Co coatings proved to be very efficient, reducing Cr volatilization by 1 order of magnitude. Microscopic studies show that both uncoated steel and steel coated with a submicrometer cobalt film develop two-layered oxide scales with the bottom part consisting of a Cr-rich corundum-type oxide. The uncoated samples develop a top layer consisting of (Cr, Mn)(3)O-4 oxide, whereas the Co-coated samples exhibit a top layer consisting of Co-rich spinel oxide. (C) 2010 The Electrochemical Society. [DOI: 10.1149/1.3462987] All rights reserved.
|
|
| 5. |
- Canovic, Sead, 1979, et al.
(författare)
-
Oxidation of Co- and Ce-nanocoated FeCr steels: A microstructural investigation
- 2013
-
Ingår i: Surface and Coatings Technology. - : Elsevier BV. - 0257-8972. ; 215, s. 62-74
-
Tidskriftsartikel (refereegranskat)abstract
- The effect of novel Co and Ce nanocoatings on oxidation behaviour and chromium volatilization from a commercial Fe-22Cr steel (Sanergy HT) developed for solid oxide fuel cell interconnect applications is investigated. Three different coatings (10 nm Ce, 640 nm Co and 10 nm Ce + 640 nm Co) are studied. Uncoated and nanocoated samples are exposed isothermally at 850 C in the air with 3% H2O for 168 h. The detailed microstructure of the different coatings is investigated. The surface morphology and microstructure of the oxide scales are characterized by using scanning electron microscopy (SEM), transmission electron microscopy (TEM), scanning transmission electron microscopy (STEM) and energy dispersive X-ray analysis (EDX). Cross-section TEM thin foils are prepared by using a combined FIB/SEM (focused ion beam/scanning electron microscope) instrument. A 640 nm cobalt coating strongly inhibits Cr volatilization but has only minor effects on oxidation rate. In contrast, a 10 nm Ce coating decreases the oxidation rate but has no significant effects on chromium volatilization. Combining the two coatings, i.e., applying a 640 nm Co coating on top of the 10 nm Ce, effectively reduces Cr evaporation and slows down the rate of alloy oxidation.
|
|
| 6. |
- Folkeson, Nicklas, 1981, et al.
(författare)
-
Fireside corrosion of stainless and low alloyed steels in a waste-fired CFB boiler; The effect of adding sulphur to the fuel
- 2008
-
Ingår i: Materials Science Forum. ; 595-598, s. 289-297
-
Tidskriftsartikel (refereegranskat)abstract
- Corrosion field tests have been carried out in the superheater region of a commercial waste-fired 75MW CFBC boiler using air cooled probes. Exposure time was 24 and 1000 hours. The effect of adding sulphur to the fuel on the corrosion of two high alloyed steels and a low alloyed steel was studied. The fuel consisted of 50% household waste and 50% industrial waste. The exposed samples were analyzed by ESEM/EDX and XRD. Metal loss was determined after 1000 hours. Both materials suffered significant corrosion in the absence of sulphur addition and the addition of sulphur to the fuel reduced corrosion significantly. The rapid corrosion of the high alloyed steel in the absence of sulphur addition is caused by the destruction of the chromium-containing protective oxide by formation of calcium chromate. Adding sulphur to the fuel inhibited chromate formation and increased the sulphate/chloride ratio in the deposit. Iron(II) chloride formed on the low alloyed steel regardless of whether sulphur was added or not.
|
|
| 7. |
- Froitzheim, Jan, 1981, et al.
(författare)
-
Long term study of Cr evaporation and high temperature corrosion behaviour of Co coated ferritic steel for solid oxide fuel cell interconnects
- 2012
-
Ingår i: Journal of Power Sources. - : Elsevier BV. - 0378-7753. ; 220, s. 217-227
-
Tidskriftsartikel (refereegranskat)abstract
- The oxidation behaviour of the uncoated ferritic Fe-22Cr steel Sanergy HT is compared with an 640 nm Co coated version of the same material. The materials have been subject to corrosion and Cr volatilization measurements in air for up to 3000 h at 850 degrees C. Oxidation tests have been carried out both isothermal and discontinuously. The volatilization measurements were carried out using a recently developed denuder technique, which allows to quantify Cr evaporation in a time resolved manner. The oxidation process is studied from very initial phases (>15 s) to long term behaviour (3000 h). The formed oxide scales are analysed by XRD, SEM/EDX as well as TEM/EDX.The results show that both materials form an oxide scale with an inner layer of Cr2O3 and a spinel layer on top. In the case of the uncoated material, the spinel layer is of (Cr,Mn)(3)O-4 type while in the presence of a Co coating a (Co,Mn,Fe)(3)O-4 is formed. The Cr evaporation measurements show that despite the fact that the Co coating is very thin (640 nm) it effectively blocks Cr evaporation for at least 3000 h. This is in line with TEM analysis showing that after 3000 h there is only a low Cr content in the outer oxide scale. This long term stability indicates the suitability of the coated material as solid oxide fuel cell (SOFC) interconnect.
|
|
| 8. |
- Herstad-Svärd, S., et al.
(författare)
-
Ramprogram – Åtgärder för samtidig minimering av alkalirelaterade driftproblem, Etapp 2
- 2007
-
Rapport (övrigt vetenskapligt/konstnärligt)abstract
- Combustion of an increasing amount of biofuel and waste woods has resulted in certainenvironmental advantages, including decreased emissions of fossil CO2, SO2 andmetals. On the other hand, a number of chloride and alkali related operational problemshave occurred which are related to combustion of these fuels.Alkali related operational problems have been studied in a project consisting of twoparts. The overall scope has been to characterise the operational problems and to studymeasures to minimise them. The first part was reported in Värmeforsk report 997 wherethe results were summarised in a table of different measures. In part two, additionalmeasures have been included in the test plan and initial corrosion has been studiedlinked to the different measures. The tests have also in part two been carried out at the12 MW CFB boiler at Chalmers. The effect of the selected measures has beeninvestigated concerning both deposit formation and bed agglomeration, and at the sametime emissions and other operational conditions were characterised.The second part of the project has among other things focused on:• To investigate measures which decrease the content of alkali and chloride in thedeposits, and consequently decrease the risk for corrosion (by investigating theinitial corrosion). Focus was also on trying to explain favourable effects.• To investigate if it is possible to combine a rather low dosage of kaolin and injectionof ammonium sulphate. This was done in order to reduce both bed agglomerationand problems from deposits during combustion of fuels rich in chlorine.• To investigate if co-combustion with sewage sludge, de-inking sludge or peat withhigh ash content, could give similar advantages as conventional additives.• Investigate if ash from PFBC is possible to use as an alternative bed material.By comparing the different measures in part two, it could be concluded that cocombustionof sewage sludge gave the best overall effect. The judgement was based onthe effects concerning bed agglomeration, level of alkali chloride in the flue gas,deposits and initial corrosion. Simultaneous addition of kaolin and ammonia sulphatealso had a favourable impact both in the bed and on the alkali chlorides in the gas phase.Dosage of kaolin did not reduce the effect of injected ammonium sulphate. Cocombustionof peat could also be a very attractive alternative, but it is critical to select asuitable peat type. It is of special concern to avoid peat with a high content of calcium,since it can increase the level of alkali chlorides by reacting with available sulphur.Change of bed material to ash from PFBC can decrease problems with bedagglomeration, but there is a risk of increased deposit formation and corrosion. A boileroperated with high steam data should consequently combine the change of bed materialwith injection of ammonium sulphate or another source of sulphur.Co-combustion of de-inking sludge from pulp and paper production can reduceproblems with bed agglomeration. There is, however, an increased chance of corrosiondue to the high content of calcium. Injection of sulphates may improve the situationconcerning corrosion. The results also showed that low potassium chlorine content in the flue gas decreasesthe risk of corrosion. Increased amount of potassium chlorine content in the flue gaswill not necessary give a high amount of chlorine content in the deposits if there is sulphur in the system.Key words: agglomeration, deposits, corrosion, alkali, kaolin, ammonium sulphate,sludge
|
|
| 9. |
|
|
| 10. |
|
|
