| 1. |
- Ekblad, Jonas, et al.
(författare)
-
Impact on rutting from introduction of increased axle loads in Finland
- 2020
-
Ingår i: The international journal of pavement engineering. - : Taylor and Francis Ltd.. - 1029-8436 .- 1477-268X.
-
Tidskriftsartikel (refereegranskat)abstract
- In 2013, Finland introduced legislation increasing gross vehicle weights (GVW) on a number of trucks. Since the actual impact on road damage is nearly impossible to quantify in advance, the present analysis of road surface measurements is intended to provide knowledge regarding the impact on road damage. Rutting is influenced by many conflated phenomena. To indicate and capture the effect on road damage due to the new maximum GVW for certain truck- and trailer combinations, the analysis follows two different but mutually supporting lines of reasoning, empirical and theoretical, respectively. Analysis of measured rut depth is supported by theoretical calculations. Theoretical findings clearly indicate that the relative increase in road damage induced by higher GVW is larger than the increase in relative payload capacity. There was a rapid fleet shift towards heavier trucks after 2013, and statistical (empirical) analysis of road surface measurements shows an increase in rutting after this introduction.
|
|
| 2. |
- Lundström, Robert, et al.
(författare)
-
Fatigue modeling as related to flexible pavement design - State of the art
- 2007
-
Ingår i: International Journal on Road Materials and Pavement Design. - : Informa UK Limited. - 1468-0629 .- 2164-7402. ; 8:2, s. 165-205
-
Forskningsöversikt (refereegranskat)abstract
- A literature study of rheological and fatigue modeling of asphalt mixtures is presented. Theoretical aspects on structural modeling, rheological behavior and the fatigue integration in design procedures are reviewed In principle, pavement design methods can be categorized in three broad groups: empirical, semi-mechanistic and fully mechanistic methods. Pavement design is generally performed using semi-mechanistic methods comprising analytical or numerical structural response models and deterioration modeling based on transfer functions and shift factors. In the case of fatigue deterioration, several approaches have been elaborated e.g. classical models, fracture mechanics and damage mechanics. The approaches differ regarding theoretical foundation and evaluation methods used. Recognizing significant limitations concerning theoretical basis as well as lack of empirical support for current design methods, a shift in paradigm from semi-empirical methods towards more advanced fully mechanistic methods have been initiated. According to this approach, improved pavements are achieved by appropriate design methods which are capable of predicting fatigue resistance in the actual pavement environment, and thus taking into account complex stress conditions, influence of temperature and material characteristics, such as aging and healing.
|
|
| 3. |
|
|
| 4. |
- Ahmad, Amais, et al.
(författare)
-
IMI – Oral biopharmaceutics tools project – Evaluation of bottom-up PBPK prediction success part 4 : Prediction accuracy and software comparisons with improved data and modelling strategies
- 2020
-
Ingår i: European journal of pharmaceutics and biopharmaceutics. - : Elsevier BV. - 0939-6411 .- 1873-3441. ; 156, s. 50-63
-
Tidskriftsartikel (refereegranskat)abstract
- Oral drug absorption is a complex process depending on many factors, including the physicochemical properties of the drug, formulation characteristics and their interplay with gastrointestinal physiology and biology. Physiological-based pharmacokinetic (PBPK) models integrate all available information on gastro-intestinal system with drug and formulation data to predict oral drug absorption. The latter together with in vitro-in vivo extrapolation and other preclinical data on drug disposition can be used to predict plasma concentration-time profiles in silico. Despite recent successes of PBPK in many areas of drug development, an improvement in their utility for evaluating oral absorption is much needed. Current status of predictive performance, within the confinement of commonly available in vitro data on drugs and formulations alongside systems information, were tested using 3 PBPK software packages (GI-Sim (ver.4.1), Simcyp® Simulator (ver.15.0.86.0), and GastroPlusTM (ver.9.0.00xx)). This was part of the Innovative Medicines Initiative (IMI) Oral Biopharmaceutics Tools (OrBiTo) project.Fifty eight active pharmaceutical ingredients (APIs) were qualified from the OrBiTo database to be part of the investigation based on a priori set criteria on availability of minimum necessary information to allow modelling exercise. The set entailed over 200 human clinical studies with over 700 study arms. These were simulated using input parameters which had been harmonised by a panel of experts across different software packages prior to conduct of any simulation. Overall prediction performance and software packages comparison were evaluated based on performance indicators (Fold error (FE), Average fold error (AFE) and absolute average fold error (AAFE)) of pharmacokinetic (PK) parameters.On average, PK parameters (Area Under the Concentration-time curve (AUC0-tlast), Maximal concentration (Cmax), half-life (t1/2)) were predicted with AFE values between 1.11 and 1.97. Variability in FEs of these PK parameters was relatively high with AAFE values ranging from 2.08 to 2.74. Around half of the simulations were within the 2-fold error for AUC0-tlast and around 90% of the simulations were within 10-fold error for AUC0-tlast. Oral bioavailability (Foral) predictions, which were limited to 19 APIs having intravenous (i.v.) human data, showed AFE and AAFE of values 1.37 and 1.75 respectively. Across different APIs, AFE of AUC0-tlast predictions were between 0.22 and 22.76 with 70% of the APIs showing an AFE > 1. When compared across different formulations and routes of administration, AUC0-tlast for oral controlled release and i.v. administration were better predicted than that for oral immediate release formulations. Average predictive performance did not clearly differ between software packages but some APIs showed a high level of variability in predictive performance across different software packages. This variability could be related to several factors such as compound specific properties, the quality and availability of information, and errors in scaling from in vitro and preclinical in vivo data to human in vivo behaviour which will be explored further. Results were compared with previous similar exercise when the input data selection was carried by the modeller rather than a panel of experts on each in vitro test. Overall, average predictive performance was increased as reflected in smaller AAFE value of 2.8 as compared to AAFE value of 3.8 in case of previous exercise.
|
|
| 5. |
- Ameur, Adam, et al.
(författare)
-
SweGen : a whole-genome data resource of genetic variability in a cross-section of the Swedish population
- 2017
-
Ingår i: European Journal of Human Genetics. - : NATURE PUBLISHING GROUP. - 1018-4813 .- 1476-5438. ; 25:11, s. 1253-1260
-
Tidskriftsartikel (refereegranskat)abstract
- Here we describe the SweGen data set, a comprehensive map of genetic variation in the Swedish population. These data represent a basic resource for clinical genetics laboratories as well as for sequencing-based association studies by providing information on genetic variant frequencies in a cohort that is well matched to national patient cohorts. To select samples for this study, we first examined the genetic structure of the Swedish population using high-density SNP-array data from a nation-wide cohort of over 10 000 Swedish-born individuals included in the Swedish Twin Registry. A total of 1000 individuals, reflecting a cross-section of the population and capturing the main genetic structure, were selected for whole-genome sequencing. Analysis pipelines were developed for automated alignment, variant calling and quality control of the sequencing data. This resulted in a genome-wide collection of aggregated variant frequencies in the Swedish population that we have made available to the scientific community through the website https://swefreq.nbis.se. A total of 29.2 million single-nucleotide variants and 3.8 million indels were detected in the 1000 samples, with 9.9 million of these variants not present in current databases. Each sample contributed with an average of 7199 individual-specific variants. In addition, an average of 8645 larger structural variants (SVs) were detected per individual, and we demonstrate that the population frequencies of these SVs can be used for efficient filtering analyses. Finally, our results show that the genetic diversity within Sweden is substantial compared with the diversity among continental European populations, underscoring the relevance of establishing a local reference data set.
|
|
| 6. |
- Berglund, Anders, et al.
(författare)
-
E-readiness of University Divisions in Online Education
- 2006
-
Ingår i: Netlearning 06', Ronneby.
-
Konferensbidrag (refereegranskat)abstract
- E-readiness can be defined as the degree to which a community is prepared to participate in the networked world. In this paper the concept of e-readiness is used in terms of how internal and external factors affect the delivery of online education offered by universities. The paper applies the macro level five forces model as adopted by Chan and Welebir (2003) in the context of micro (university divisional level). Thus, the purpose is not to have generalizable findings, but rather use the delivery of online education as determinant for the level of universities' e-readiness, and explore the factors affecting e-readiness and ways of utilizing the factors as central to the study. Using a qualitative method case study interviews on divisional level were used to obtain in-depth empirical evidence. The study appears to indicate potential need to further modify the five forces model by Chan and Welebir (2003) due to the non-commercial natureof the Swedish education system. Also, co-operation in providing educational services such as the Net University in Sweden precludes market forces determination by universities internally. No specialized training program for the instructors to fit any special needs of students particular to online education was perceived.
|
|
| 7. |
- Bylesjö, Max, et al.
(författare)
-
Integrated analysis of transcript, protein and metabolite data to study lignin biosynthesis in hybrid aspen
- 2009
-
Ingår i: Journal of Proteome Research. - : American Chemical Society (ACS). - 1535-3893 .- 1535-3907. ; 8:1, s. 199-210
-
Tidskriftsartikel (refereegranskat)abstract
- Tree biotechnology will soon reach a mature state where it will influence the overall supply of fiber, energy and wood products. We are now ready to make the transition from identifying candidate genes, controlling important biological processes, to discovering the detailed molecular function of these genes on a broader, more holistic, systems biology level. In this paper, a strategy is outlined for informative data generation and integrated modeling of systematic changes in transcript, protein and metabolite profiles measured from hybrid aspen samples. The aim is to study characteristics of common changes in relation to genotype-specific perturbations affecting the lignin biosynthesis and growth. We show that a considerable part of the systematic effects in the system can be tracked across all platforms and that the approach has a high potential value in functional characterization of candidate genes.
|
|
| 8. |
- Eliasson, Sara, et al.
(författare)
-
A life cycle energy and weight comparison of a carbon fibercomposite versus metallic component in a commercial vehicle
- 2021
-
Ingår i: A life cycle energy and weight comparison of a carbon fibercomposite versus metallic component in a commercialvehicle.
-
Konferensbidrag (övrigt vetenskapligt/konstnärligt)abstract
- Lightweight design is important for Battery Electric Vehicles (BEVs), to minimize the effects from the added weight of the batteries. The study looks at the benefits and disadvantages of choosing a Carbon Fiber Reinforced Polymer (CFRP) material in comparison to metallic material for a specific battery electric commercial vehicle component. A Life Cycle Energy (LCE) and weight analysis are the basis for the comparison. Other aspects that could be considered important for the industrial implementation, such as cost, are also discussed. The LCE is assessed using a combination of engineering process modelling, available data from industrial partners, and data available in the literature. The analysis is aimed to support a holistic comparison, which means the modelling is performed on an overarching level of detail.
|
|
| 9. |
- Fadil, Hassan, 1990-
(författare)
-
New Experimental and Modelling Tools for Multiscale Characterization of Asphalt Mastic
- 2020
-
Licentiatavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Asphalt mastics act as a binding phase in asphalt mixtures and their rheological properties strongly affect the performance of asphalt mixtures with respect to virtually all damage modes. In order to measure mastics properties, relevant for field performance, testing should be performed at size-scales representative for the morphology and material inhomogeneity of asphalt mixtures. This thesis aims to contribute to solving these important issues by developing new experimental and modelling tools for the multi-scale characterization of asphalt mastics.An instrumented indentation test for viscoelastic characterization of asphalt mastics is proposed as a new alternative to existing techniques. A methodology for spherical indentation testing of bituminous materials is developed allowing measuring their viscoelastic properties at arbitrary non-decreasing loading. The potential of indentation tests for multi-scale measurements of viscoelastic properties of binder-aggregate composites is investigated for the special case of asphalt mortar, composed of mastic and aggregates smaller than 2.36 mm. The effect of the test parameters on the measured apparent shear relaxation modulus of asphalt mortar is evaluated. Experimental and modelling results indicate that the measurement scale in the indentation tests can be controlled efficiently by testing with different indenter-specimen contact areas. Accordingly, indentation tests may be used for reliable viscoelastic characterization of binder-aggregate composites on macro-scale as well as on the mastic phase level. It may thus potentially provide a relatively simple tool for measuring viscoelastic properties of mastics in situ in asphalt mixtures. In order to establish a quantitative link between material design parameters of mastics and its rheology, a new finite element (FE) micromechanical modelling approach has been developed. It allows predicting the viscoelastic properties of bitumen-filler mastic from its volumetric, mechanical and geometrical design parameters. The influence of modelling parameters on the model’s accuracy is evaluated and optimal parameter combinations are identified. The model is validated with the measurements performed on several mastics and for a range of volumetric concentration of filler. It is shown that the proposed model can capture the measured viscoelastic behaviour of mastics for the examined range of loading, temperature and material parameters. Accordingly, it may be a useful tool for optimizing mastics material design for the target viscoelastic properties.
|
|
| 10. |
- Haas, Brian J., et al.
(författare)
-
Genome sequence and analysis of the Irish potato famine pathogen Phytophthora infestans
- 2009
-
Ingår i: Nature. - : Springer Science and Business Media LLC. - 0028-0836 .- 1476-4687. ; 461:7262, s. 393-398
-
Tidskriftsartikel (refereegranskat)abstract
- Phytophthora infestans is the most destructive pathogen of potato and a model organism for the oomycetes, a distinct lineage of fungus-like eukaryotes that are related to organisms such as brown algae and diatoms. As the agent of the Irish potato famine in the mid-nineteenth century, P. infestans has had a tremendous effect on human history, resulting in famine and population displacement(1). To this day, it affects world agriculture by causing the most destructive disease of potato, the fourth largest food crop and a critical alternative to the major cereal crops for feeding the world's population(1). Current annual worldwide potato crop losses due to late blight are conservatively estimated at $6.7 billion(2). Management of this devastating pathogen is challenged by its remarkable speed of adaptation to control strategies such as genetically resistant cultivars(3,4). Here we report the sequence of the P. infestans genome, which at similar to 240 megabases (Mb) is by far the largest and most complex genome sequenced so far in the chromalveolates. Its expansion results from a proliferation of repetitive DNA accounting for similar to 74% of the genome. Comparison with two other Phytophthora genomes showed rapid turnover and extensive expansion of specific families of secreted disease effector proteins, including many genes that are induced during infection or are predicted to have activities that alter host physiology. These fast-evolving effector genes are localized to highly dynamic and expanded regions of the P. infestans genome. This probably plays a crucial part in the rapid adaptability of the pathogen to host plants and underpins its evolutionary potential.
|
|
