| 1. |
- Nordin, E. Z., et al.
(författare)
-
Secondary organic aerosol formation from gasoline passenger vehicle emissions investigated in a smog chamber
- 2012
-
Ingår i: Atmospheric Chemistry and Physics Discussions. - : Copernicus Publications. - 1680-7367 .- 1680-7375. ; 12:12, s. 31725-31765
-
Tidskriftsartikel (refereegranskat)abstract
- Gasoline vehicles have elevated emissions of volatile organic compounds during cold starts and idling and have recently been pointed out as potentially the main source of anthropogenic secondary organic aerosol (SOA) in megacities. However, there is a lack of laboratory studies to systematically investigate SOA formation in real-world exhaust. In this study, SOA formation from pure aromatic precursors, idling and cold start gasoline exhaust from one Euro II, one Euro III and one Euro IV passenger vehicles were investigated using photo-oxidation experiments in a 6 m3 smog chamber. The experiments were carried out at atmospherically relevant organic aerosol mass concentrations. The characterization methods included a high resolution aerosol mass spectrometer and a proton transfer mass spectrometer. It was found that gasoline exhaust readily forms SOA with a signature aerosol mass spectrum similar to the oxidized organic aerosol that commonly dominates the organic aerosol mass spectra downwind urban areas. After 4 h aging the formed SOA was 1–2 orders of magnitude higher than the Primary OA emissions. The SOA mass spectrum from a relevant mixture of traditional light aromatic precursors gave f43 (mass fraction at m/z = 4 3) approximately two times higher than to the gasoline SOA. However O : C and H : C ratios were similar for the two cases. Classical C6–C9 light aromatic precursors were responsible for up to 60% of the formed SOA, which is significantly higher than for diesel exhaust. Important candidates for additional precursors are higher order aromatic compounds such as C10, C11 light aromatics, naphthalene and methyl-naphthalenes.
|
|
| 2. |
- Caplat, Paul, et al.
(författare)
-
Looking beyond the mountain: dispersal barriers in a changing world
- 2016
-
Ingår i: Frontiers in Ecology and the Environment. - : Wiley. - 1540-9295 .- 1540-9309. ; 14:5, s. 262-269
-
Tidskriftsartikel (refereegranskat)abstract
- Dispersal barriers have demographic, evolutionary, and ecosystem-wide consequences. With ongoing changes in the environment, some dispersal barriers will likely disappear while new ones will appear, and it is crucial to understand these dynamics to forecast species' distributions and adaptive potential. Here we review recent literature on the ecological and evolutionary aspects of dispersal to highlight key dynamics of dispersal barriers in the face of global change. After defining dispersal barriers, we explain that a better understanding of their dynamics requires identifying the barrier types that are most susceptible to change and predicting species' responses. This knowledge is a prerequisite for designing management strategies to increase or reduce connectivity, and maintain adaptive potential. Our intent is to motivate researchers to explicitly consider dispersal barriers in order to better forecast the dynamics of species and ecosystems subject to global change.
|
|
| 3. |
- Tesson, Sylvie V M, et al.
(författare)
-
Integrating microorganism and macroorganism dispersal: modes, techniques and challenges with particular focus on co-dispersal
- 2015
-
Ingår i: Ecoscience. - : Informa UK Limited. - 1195-6860. ; 22:2-4, s. 109-124
-
Tidskriftsartikel (refereegranskat)abstract
- Whatever their size and the ecosystem they live in, all organisms may disperse at some stage of their life cycle. Dispersal dynamics are to a varying extent dependent on organismal size, life history, ecological niche, survival capacities and phylogeny. Moves towards a synthesis in dispersal ecology have focused primarily on vertebrates and higher plants, yet recent studies suggest that the dispersal of microorganisms and macroorganisms has much more in common than previously assumed. The dispersal of one organism enables co-dispersal for many others, smaller in size. There is an increasing need for a more integrated approach to study dispersal within the context of organismal interactions and their environments. Such an approach is facilitated by recent developments of powerful indirect techniques that enable tracking of microorganisms and macroorganisms over multiple spatial and temporal scales. Likewise, dispersal modelling and theoretical models of the consequences of dispersal can inspire empirical studies across the entire size spectrum. Simultaneously studying the relationships between dispersal of microorganisms and macroorganisms, and accounting for dispersal through time and space, will allow us to better understand the functioning and dynamics of communities and ecosystems, and to make better predictions of future dispersal patterns, changes in biodiversity and connectivity.
|
|
| 4. |
- Ahlberg, Erik, et al.
(författare)
-
"Vi klimatforskare stödjer Greta och skolungdomarna"
- 2019
-
Ingår i: Dagens nyheter (DN debatt). - 1101-2447.
-
Tidskriftsartikel (populärvet., debatt m.m.)abstract
- DN DEBATT 15/3. Sedan industrialiseringens början har vi använt omkring fyra femtedelar av den mängd fossilt kol som får förbrännas för att vi ska klara Parisavtalet. Vi har bara en femtedel kvar och det är bråttom att kraftigt reducera utsläppen. Det har Greta Thunberg och de strejkande ungdomarna förstått. Därför stödjer vi deras krav, skriver 270 klimatforskare.
|
|
| 5. |
- Kristensson, Adam, et al.
(författare)
-
Size-Resolved Respiratory Tract Deposition of Sub-Micrometer Aerosol Particles in a Residential Area with Wintertime Wood Combustion
- 2013
-
Ingår i: Aerosol and Air Quality Research. - : Taiwan Association for Aerosol Research. - 1680-8584 .- 2071-1409. ; 13:1, s. 24-35
-
Tidskriftsartikel (refereegranskat)abstract
- Particle size distributions and hygroscopic growth were studied in a town in Sweden with extensive emissions from wood combustion. The average deposited fraction of particle number, surface area and volume dose in the human respiratory tract was estimated using the data set, as well as the typical deposition pattern of the two dominant particle source types: wood combustion and traffic exhaust. As far as we know, this is the first report on the deposited fraction and hygroscopicity of ambient particles from domestic wood combustion in the literature. The use of PM2.5 as a substitute for the deposited dose was also tested. Source/receptor modeling and the hygroscopicity measurements showed that wood combustion and traffic exhaust are dominant sources, and that these particles have a low water uptake. Number fractions of 38 and 69% of the wood combustion and traffic particles, respectively, were deposited in the respiratory tract, and 53% of the particles were deposited as an average for the whole period. The deposited fraction of the surface area and volume dose was also calculated for wood combustion particles, with the result being 22% for both parameters. The results also revealed that the PM2.5 average over more than 10 hours correlated well (r(2) > 0.80) with the deposited surface area and volume dose. This means that PM2.5 can be used as proxy for the deposited dose when examining health effect relationships during short-term exposure studies if the averaging time is sufficient, while a PM2.5 proxy is not recommended for shorter averaging times.
|
|
| 6. |
- Rissler, Jenny, et al.
(författare)
-
Experimental determination of deposition of diesel exhaust particles in the human respiratory tract
- 2012
-
Ingår i: Journal of Aerosol Science. - : Elsevier BV. - 0021-8502 .- 1879-1964. ; 48, s. 18-33
-
Tidskriftsartikel (refereegranskat)abstract
- Diesel emissions are a major contributor to combustion-generated airborne ambient particles. To understand the role of diesel particulate emissions on health effects, it is important to predict the actual particulate dose deposited in the human respiratory tract, with respect to number, surface area and mass. This is complicated by the agglomerate nature of some of these particles. In this study the respiratory tract deposition fraction in the size range 10-500 nm, was determined for 10 healthy volunteers during both idling and transient engine running conditions of a heavy duty diesel engine. The aerosol was characterized with respect to both chemical and physical properties including size resolved particle effective density. The dominating part of the emitted particles had an agglomerate structure. For those formed during transient running conditions, the relationship between particle mass and mobility diameter could be described by a power law function. This was not the case during idling, most likely because of volatile compounds condensing on the agglomerates. The respiratory tract particle deposition revealed large intra-subject variability with some subjects receiving a dose that was twice as high as that of others, when exposed to the same particle concentration. Associations were found between total deposited fractions (TDF), and breathing pattern. There was a difference between the idling and transient cycle with TDF being higher with respect to number during idling. The measured size-dependent deposition fraction of the agglomerated exhaust particles from both running conditions was nearly identical and closely resembled that of spherical hydrophobic particles, if plotted as a function of mobility diameter. Thus, for the size range covered, the mobility diameter could well describe the diameter-dependent particle respiratory tract deposition probability, regardless of the agglomeration state of the particles. Whilst mobility diameter well describes the deposition fraction, more information about particle characteristics is needed to convert this to volume equivalent diameter or estimate dose with respect to surface area or mass. A methodology is presented and applied to calculate deposited dose by surface area and mass of agglomerated particles. The methodology may be useful in similar studies estimating dose to the lung, deposition onto cell cultures and in animal studies. (C) 2012 Elsevier Ltd. All rights reserved.
|
|
| 7. |
- Rissler, Jenny, et al.
(författare)
-
Effective Density and Mixing State of Aerosol Particles in a Near-Traffic Urban Environment.
- 2014
-
Ingår i: Environmental Science & Technology. - : American Chemical Society (ACS). - 1520-5851 .- 0013-936X. ; 48:11, s. 6300-6308
-
Tidskriftsartikel (refereegranskat)abstract
- In urban environments, airborne particles are continuously emitted, followed by atmospheric aging. Also, particles emitted elsewhere, transported by winds, contribute to the urban aerosol. We studied the effective density (mass-mobility relationship) and mixing state with respect to the density of particles in central Copenhagen, in wintertime. The results are related to particle origin, morphology, and aging. Using a differential mobility analyzer-aerosol particle mass analyzer (DMA-APM), we determined that particles in the diameter range of 50-400 nm were of two groups: porous soot aggregates and more dense particles. Both groups were present at each size in varying proportions. Two types of temporal variability in the relative number fraction of the two groups were found: soot correlated with intense traffic in a diel pattern and dense particles increased during episodes with long-range transport from polluted continental areas. The effective density of each group was relatively stable over time, especially of the soot aggregates, which had effective densities similar to those observed in laboratory studies of fresh diesel exhaust emissions. When heated to 300 °C, the soot aggregate volatile mass fraction was ∼10%. For the dense particles, the volatile mass fraction varied from ∼80% to nearly 100%.
|
|
| 8. |
- Roger, Fabian, et al.
(författare)
-
Airborne environmental DNA metabarcoding for the monitoring of terrestrial insects—A proof of concept from the field
- 2022
-
Ingår i: Environmental DNA. - : Wiley. - 2637-4943. ; 4:4, s. 790-807
-
Tidskriftsartikel (refereegranskat)abstract
- Biodiversity is in decline due to human-induced pressures on ecosystems around the world. To be able to counteract this alarming trend, it is paramount to closely monitor biodiversity at global scales. Because this is practically impossible with traditional methods, the last decade has seen a strong push for new solutions. In aquatic ecosystems, the monitoring of species from environmental DNA (eDNA) has emerged as one of the most powerful tools at our disposal, but in terrestrial ecosystems, the power of eDNA for monitoring has so far been hampered by the local scale of the samples. In this study, we report the successful detection of insects from airborne eDNA from samples taken in the field. We compare our results to two traditional insect monitoring methods (1) light traps for moth monitoring and (2) transect walks for the monitoring of butterflies and wild bees. Airborne eDNA metabarcoding revealed DNA from six classes of arthropods, and twelve order of insects—including representatives from the four largest orders: Diptera (flies), Lepidoptera (butterflies and moths), Coleoptera (beetles), and Hymenoptera (bees, wasps, and ants). We did not detect all species observed using traditional methods and suggest further directions for the development of airborne eDNA metabarcoding. We also recovered DNA from nine species of vertebrates, including frogs, birds, and mammals as well as from 12 other phyla. Airborne eDNA has the potential to become a powerful tool for terrestrial biodiversity monitoring, with many impactful applications including the monitoring of pests, invasive, or endangered species and disease vectors.
|
|
| 9. |
- Santl-Temkiv, Tina, et al.
(författare)
-
High-Flow-Rate Impinger for the Study of Concentration, Viability, Metabolic Activity, and Ice-Nucleation Activity of Airborne Bacteria
- 2017
-
Ingår i: Environmental Science and Technology. - : American Chemical Society (ACS). - 0013-936X .- 1520-5851. ; 51:19, s. 11224-11234
-
Tidskriftsartikel (refereegranskat)abstract
- The study of airborne bacteria relies on a sampling strategy that preserves their integrity and in situ physiological state, e.g. viability, cultivability, metabolic activity, and ice-nucleation activity. Because ambient air harbors low concentrations of bacteria, an effective bioaerosol sampler should have a high sampling efficiency and a high airflow. We characterize a high-flow-rate impinger with respect to particle collection and retention efficiencies in the range 0.5-3.0 μm, and we investigated its ability to preserve the physiological state of selected bacterial species and seawater bacterial community in comparison with four commercial bioaerosol samplers. The collection efficiency increased with particle size and the cutoff diameter was between 0.5 and 1 μm. During sampling periods of 120-300 min, the impinger retained the cultivability, metabolic activity, viability, and ice-nucleation activity of investigated bacteria. Field studies in semiurban, high-altitude, and polar environments included periods of low bacterial air concentrations, thus demonstrating the benefits of the impinger's high flow rate. In conclusion, the impinger described here has many advantages compared with other bioaerosol samplers currently on the market: a potential for long sampling time, a high flow rate, a high sampling and retention efficiency, low costs, and applicability for diverse downstream microbiological and molecular analyses.
|
|
| 10. |
- Hussein, Tareq, et al.
(författare)
-
Regional inhaled deposited dose of indoor combustion-generated aerosols in jordanian urban homes
- 2020
-
Ingår i: Atmosphere. - : MDPI AG. - 2073-4433. ; 11:11
-
Tidskriftsartikel (refereegranskat)abstract
- Indoor combustion processes associated with cooking, heating, and smoking are a major source of aerosols in Jordanian dwellings. To evaluate human exposure to combustion-generated aerosols in Jordanian indoor environments, regional inhaled deposited dose rates of indoor aerosols (10 nm to 25 µm) were determined for different scenarios for adult occupants. The inhaled deposited dose rate provides an estimate of the number or mass of inhaled aerosol that deposits in each region of the respiratory system per unit time. In general, sub-micron particle number (PN1) dose rates ranged from 109 to 1012 particles/h, fine particle mass (PM2.5) dose rates ranged from 3 to 216 µg/h, and coarse particle mass (PM10) dose rates ranged from 30 to 1600 µg/h. Dose rates were found to be dependent on the type and intensity of indoor combustion processes documented in the home. Dose rates were highest during cooking activities using a natural gas stove, heating via natural gas and kerosene, and smoking (shisha/tobacco). The relative fraction of the total dose rate received in the head airways, tracheobronchial, and alveolar regions varied among the documented indoor combustion (and non-combustion) activities. The significant fraction of sub-100 nm particles produced during the indoor combustion processes resulted in high particle number dose rates for the alveolar region. Suggested approaches for reducing indoor aerosol dose rates in Jordanian dwellings include a reduction in the prevalence of indoor combustion sources, use of extraction hoods to remove combustion products, and improved ventilation/filtration in residential buildings.
|
|
