| 1. |
- Allaire, C., et al.
(författare)
-
Beam test measurements of Low Gain Avalanche Detector single pads and arrays for the ATLAS High Granularity Timing Detector
- 2018
-
Ingår i: Journal of Instrumentation. - : Institute of Physics (IOP). - 1748-0221. ; 13
-
Tidskriftsartikel (refereegranskat)abstract
- For the high luminosity upgrade of the LHC at CERN, ATLAS is considering the addition of a High Granularity Timing Detector (HGTD) in front of the end cap and forward calorimeters at vertical bar z vertical bar = 3:5 m and covering the region 2:4 < vertical bar eta vertical bar < 4 to help reducing the effect of pile-up. The chosen sensors are arrays of 50 mu m thin Low Gain Avalanche Detectors (LGAD). This paper presents results on single LGAD sensors with a surface area of 1.3 x 1.3 mm(2) and arrays with 2 x 2 pads with a surface area of 2 x 2 mm(2) or 3 x 3 mm(2) each and different implant doses of the p(+) multiplication layer. They are obtained from data collected during a beam test campaign in autumn 2016 with a pion beam of 120 GeV energy at the CERN SPS. In addition to several quantities measured inclusively for each pad, the gain, efficiency and time resolution have been estimated as a function of the position of the incident particle inside the pad by using a beam telescope with a position resolution of few mu m. Different methods to measure the time resolution are compared, yielding consistent results. The sensors with a surface area of 1.3 x 1.3 mm(2) have a time resolution of about 40 ps for a gain of 20 and of about 27 ps for a gain of 50 and fulfil the HGTD requirements. Larger sensors have, as expected, a degraded time resolution. All sensors show very good efficiency and time resolution uniformity.
|
|
| 2. |
- Blösch, Günter, et al.
(författare)
-
Twenty-three unsolved problems in hydrology (UPH) - a community perspective
- 2019
-
Ingår i: Hydrological Sciences Journal. - : Informa UK Limited. - 0262-6667 .- 2150-3435. ; 64:10, s. 1141-1158
-
Tidskriftsartikel (refereegranskat)abstract
- This paper is the outcome of a community initiative to identify major unsolved scientific problems in hydrology motivated by a need for stronger harmonisation of research efforts. The procedure involved a public consultation through online media, followed by two workshops through which a large number of potential science questions were collated, prioritised, and synthesised. In spite of the diversity of the participants (230 scientists in total), the process revealed much about community priorities and the state of our science: a preference for continuity in research questions rather than radical departures or redirections from past and current work. Questions remain focused on the process-based understanding of hydrological variability and causality at all space and time scales. Increased attention to environmental change drives a new emphasis on understanding how change propagates across interfaces within the hydrological system and across disciplinary boundaries. In particular, the expansion of the human footprint raises a new set of questions related to human interactions with nature and water cycle feedbacks in the context of complex water management problems. We hope that this reflection and synthesis of the 23 unsolved problems in hydrology will help guide research efforts for some years to come.
|
|
| 3. |
- Hering, Alessa, et al.
(författare)
-
Learn2Reg: comprehensive multi-task medical image registration challenge, dataset and evaluation in the era of deep learning
- 2023
-
Ingår i: IEEE Transactions on Medical Imaging. - : Institute of Electrical and Electronics Engineers (IEEE). - 0278-0062 .- 1558-254X. ; 42:3, s. 697-712
-
Tidskriftsartikel (refereegranskat)abstract
- Image registration is a fundamental medical image analysis task, and a wide variety of approaches have been proposed. However, only a few studies have comprehensively compared medical image registration approaches on a wide range of clinically relevant tasks. This limits the development of registration methods, the adoption of research advances into practice, and a fair benchmark across competing approaches. The Learn2Reg challenge addresses these limitations by providing a multi-task medical image registration data set for comprehensive characterisation of deformable registration algorithms. A continuous evaluation will be possible at https:// learn2reg.grand-challenge.org. Learn2Reg covers a wide range of anatomies (brain, abdomen, and thorax), modalities (ultrasound, CT, MR), availability of annotations, as well as intra- and inter-patient registration evaluation. We established an easily accessible framework for training and validation of 3D registration methods, which enabled the compilation of results of over 65 individual method submissions from more than 20 unique teams. We used a complementary set of metrics, including robustness, accuracy, plausibility, and runtime, enabling unique insight into the current state-of-the-art of medical image registration. This paper describes datasets, tasks, evaluation methods and results of the challenge, as well as results of further analysis of transferability to new datasets, the importance of label supervision, and resulting bias. While no single approach worked best across all tasks, many methodological aspects could be identified that push the performance of medical image registration to new state-of-the-art performance. Furthermore, we demystified the common belief that conventional registration methods have to be much slower than deep-learning-based methods.
|
|
| 4. |
- Koundouri, P., et al.
(författare)
-
Methodology for Integrated Socio-economic Assessment of Multi-use Offshore Platforms.
- 2017
-
Ingår i: In: Koundouri P. (eds) The Ocean of Tomorrow. Environment & Policy, vol 56. Springer, Cham. - 9783319557700 ; , s. 11-26
-
Bokkapitel (övrigt vetenskapligt/konstnärligt)abstract
- This chapter presents the methodology employed for the Integrated Socio-Economic Assessment (MISEA) of different designs of Multi-Use Offshore Platforms (MUOPs). The methodology allows for the identification, the valuationand the assessment of the potential impacts and their magnitude. The analysis considers a number of feasible designs of MUOP investments, and the likely responsesof those impacted by the investment project. The approach provides decision-makers with a valuable tool to assess whether a MUOP project increases the overall social welfare and hence should be undertaken. This is performed under alternative specifications regarding platform design, the discount rate and the stream of net benefits, if a Cost-Benefit Analysis (CBA) is to be followed or a sensitivity analysis of selected criteria in a Multi-Criteria Decision Analysis (MCDA) framework. Themethodology can support the implementation of policies aiming at achieving a goodenvironmental status of the EU’s marine waters and the protection of the resource base upon which marine-related economic and social activities depend.
|
|
| 5. |
- Lange, Jonathan, et al.
(författare)
-
Novel lithographic printing techniques enabling sustainable and high quality multi material manufacturing process for future space outposts
- 2021
-
Ingår i: IAC 2021 Congress Proceedings, 72nd International Astronautical Congress (IAC), Dubai, United Arab Emirates. - : International Astronautical Federation (IAF).
-
Konferensbidrag (refereegranskat)abstract
- Several challenges remain before the full potential of on-orbit manufacturing can be realized. There may be some limitations to the types of items that can be manufactured in space. Such limitations could be caused by a variety of factors, including the materials required for a particular structure, the size of the object to be manufactured, the time required to execute the architecture, the configuration of the object being manufactured, and the raw material needed to support the manufacturing process. The complementary challenge to the relevant fabrication processes is the possibility to achieve the required precision demanded by geometrically complex structures and the ability to be versatile in processing a broad material spectrum. In this context, novel lithographic 3D printing techniques will be an asset to pave the way towards overcoming these challenges. Currently, the European Space Agency (ESA) is investigating the implementation of such technology in the context of a lunar base. In particular, two different applications are being studied: • Lithography-Based Ceramic Manufacturing (LCM), where the ceramic powder is distributed in a photocurable monomer formulation in presence of a photoinitiator. Ceramic materials are extensively used in a vast number of technological processes as well as in space applications. They are usually considered as the material of choice for applications where other materials such as plastic and metal fail to deliver the required performance. The LCM process will also allow processing lunar regolith simulant adding value to the current material portfolio of this technique, as well as to the range of processes potentially applicable on the lunar or Martian surface. • Lithography-based Metal Manufacturing (LMM) for processing metallic powders. In contrast to the currently predominantly used powder bed fusion (direct metal laser melting) techniques, this process uses a paste/suspension as feedstock and hence, does not rely on the use of highly spherical gas atomized powders. This will enable the utilization of recycled powders from scrap metals that are available at Moon bases or of metallic alloys reduced from lunar regolith, thus providing higher flexibility in accepting raw material with poor quality and purity. The paper addresses the results from both activities in terms of printed parts quality (roughness, density, resolution and accuracy) as well as the implementation requirements for the whole process chain, including suitable pre- and post-processing steps, with the aim to achieve a zero-waste flow in a lunar environment.
|
|
| 6. |
- Correa, J., et al.
(författare)
-
Characterisation of a PERCIVAL monolithic active pixel prototype using synchrotron radiation
- 2016
-
Ingår i: Journal of Instrumentation. - : IOP. - 1748-0221. ; 11:2
-
Tidskriftsartikel (refereegranskat)abstract
- PERCIVAL ("Pixelated Energy Resolving CMOS Imager, Versatile And Large") is a monolithic active pixel sensor (MAPS) based on CMOS technology. Is being developed by DESY, RAL/STFC, Elettra, DLS, and PAL to address the various requirements of detectors at synchrotron radiation sources and Free Electron Lasers (FELs) in the soft X-ray regime. These requirements include high frame rates and FELs base-rate compatibility, large dynamic range, single-photon counting capability with low probability of false positives, high quantum efficiency (QE), and (multi-)megapixel arrangements with good spatial resolution. Small-scale back-side-illuminated (BSI) prototype systems are undergoing detailed testing with X-rays and optical photons, in preparation of submission of a larger sensor. A first BSI processed prototype was tested in 2014 and a preliminary result—first detection of 350eV photons with some pixel types of PERCIVAL—reported at this meeting a year ago. Subsequent more detailed analysis revealed a very low QE and pointed to contamination as a possible cause. In the past year, BSI-processed chips on two more wafers were tested and their response to soft X-ray evaluated. We report here the improved charge collection efficiency (CCE) of different PERCIVAL pixel types for 400eV soft X-rays together with Airy patterns, response to a flat field, and noise performance for such a newly BSI-processed prototype sensor.
|
|
| 7. |
- Correa, J., et al.
(författare)
-
On the Charge Collection Efficiency of the PERCIVAL Detector
- 2016
-
Ingår i: Journal of Instrumentation. - : IOP. - 1748-0221. ; 11:12
-
Tidskriftsartikel (refereegranskat)abstract
- The PERCIVAL soft X-ray imager is being developed by DESY, RAL, Elettra, DLS, and PAL to address the challenges at high brilliance Light Sources such as new-generation Synchrotrons and Free Electron Lasers. Typical requirements for detector systems at these sources are high frame rates, large dynamic range, single-photon counting capability with low probability of false positives, high quantum efficiency, and (multi)-mega-pixel arrangements. PERCIVAL is a monolithic active pixel sensor, based on CMOS technology. It is designed for the soft X-ray regime and, therefore, it is post-processed in order to achieve high quantum efficiency in its primary energy range (250 eV to 1 keV) . This work will report on the latest experimental results on charge collection efficiency obtained for multiple back-side-illuminated test sensors during two campaigns, at the P04 beam-line at PETRA III, and the CiPo beam-line at Elettra, spanning most of the primary energy range as well as testing the performance for photon-energies below 250 eV . In addition, XPS surface analysis was used to cross-check the obtained results.
|
|
| 8. |
- Graafsma, Heinz, et al.
(författare)
-
PERCIVAL soft X-ray imager
- 2013
-
Ingår i: IEEE Nuclear Science Symposium Conference Record. - : IEEE conference proceedings. - 9781479905348 ; , s. Art. no. 6829506-
-
Konferensbidrag (refereegranskat)abstract
- Our goal is to provide the scientific community with a large (10cm × 10cm) pixellated detector featuring a large dynamic range (1-105 photons), good spatial resolution (27μm), good Quantum Efficiency (QE) in the low energy range (250eV-1keV), variable readout speed (up to 120 frames/s), i.e. with characteristics compatible with user needs at today's of low-energy Free Electron Lasers (FEL) and synchrotron sources. © 2013 IEEE.
|
|
| 9. |
- Holttinen, H., et al.
(författare)
-
Design and operation of power systems with large amounts of wind power
- 2009
-
Bok (refereegranskat)abstract
- There are already several power systems coping with large amounts of wind power. Hi h penetration of wind power has impacts that have to be manage through proper plant interconnection, integration, transmission planning, and system and market operations. This report is a summary of case studies addressing concerns about the impact of wind power.s variability and uncertainty on power system reliability and costs. The case studies summarized in this report are not easy to compare due to different methodology and data used, as well as different assumptions on the interconnection capacity available. Integration costs of wind power need to be compared to something, like the production costs or market value of wind power, or integration cost of other production forms. There is also benefit when adding wind power to power systems: it reduces the total operating costs and emissions as wind fossil fuels. Severalissues that impact on the amount of wind power that can be integrated have been identified. Large balancing areas and aggregation benefits of large areas help in reducing the variability and forecast errors of wind power as well as help in pooling more cost effective balancing resources. System operation and working electricity markets at less than day-ahead time scales help reduce forecast errors of wind power. Transmission is the key to aggregation benefits, electricity markets and larger balancing areas. From the investigated studies it follows that at wind penetrations of up to 20 % of gross demand (energy), system operating cost increases arising from wind variability and uncertainty amounted to about 1.4 ./MWh. This is 10 % or less of the wholesale value of the wind energy.
|
|
| 10. |
- Khromova, A., et al.
(författare)
-
Report on recent results of the PERCIVAL soft X-ray imager
- 2016
-
Ingår i: Journal of Instrumentation. - : IOP. - 1748-0221. ; 11:November
-
Tidskriftsartikel (refereegranskat)abstract
- The PERCIVAL (Pixelated Energy Resolving CMOS Imager, Versatile And Large) soft X-ray 2D imaging detector is based on stitched, wafer-scale sensors possessing a thick epi-layer, which together with back-thinning and back-side illumination yields elevated quantum efficiency in the photon energy range of 125–1000 eV. Main application fields of PERCIVAL are foreseen in photon science with FELs and synchrotron radiation. This requires high dynamic range up to 105 ph @ 250 eV paired with single photon sensitivity with high confidence at moderate frame rates in the range of 10–120 Hz. These figures imply the availability of dynamic gain switching on a pixel-by-pixel basis and a highly parallel, low noise analog and digital readout, which has been realized in the PERCIVAL sensor layout. Different aspects of the detector performance have been assessed using prototype sensors with different pixel and ADC types. This work will report on the recent test results performed on the newest chip prototypes with the improved pixel and ADC architecture. For the target frame rates in the 10–120 Hz range an average noise floor of 14e− has been determined, indicating the ability of detecting single photons with energies above 250 eV. Owing to the successfully implemented adaptive 3-stage multiple-gain switching, the integrated charge level exceeds 4 centerdot 106 e− or 57000 X-ray photons at 250 eV per frame at 120 Hz. For all gains the noise level remains below the Poisson limit also in high-flux conditions. Additionally, a short overview over the updates on an oncoming 2 Mpixel (P2M) detector system (expected at the end of 2016) will be reported.
|
|
