| 1. |
- Ding, C., et al.
(författare)
-
Study on fracture of the fibrous monolith cemented carbide
- 2013
-
Ingår i: Advanced Materials Research. - 1662-8985 .- 1022-6680. ; 815, s. 43-47
-
Konferensbidrag (refereegranskat)abstract
- A fibrous monolith cemented carbide with WC-6%Co as cell and WC-20%Co as cell boundaries was produced through hot co-extrusion process in this paper. The density, hardness, transverse rupture strength (TRS) and fracture toughness (KIc) of the fibrous monolith cemented carbide were tested, and the fracture and crack propagation were observed by metalloscope and Scanning Electron Microscope. The result shows fibrous monolith structure design could effectively improve the TRS and the KIc of WC/Co cemented carbide without a significant decrease of hardness. It is the reason of high transverse rupture strength and fracture toughness that WC-20%Co can absorb more fracture energy in order to slow, prevent, or deflect crack propagation, proved by metalloscope and scanning electron microscope.
|
|
| 2. |
- Xin, Zhiging, et al.
(författare)
-
Scalable Fabrication of Conductive Lines by Patterned Wettability-Assisted Bar-Coating for Low Cost Paper-Based Circuits
- 2019
-
Ingår i: Advanced Materials Interfaces. - : Wiley-VCH Verlag. - 2196-7350. ; 6:10
-
Tidskriftsartikel (refereegranskat)abstract
- Patterning technology on the paper based on wettability difference for paper-based devices has attracted significant attention for its low cost, easy degradability, and high flexibility. Here, conductive lines are rapidly prepared by patterned wettability-assisted bar-coating for low cost paper-based circuits. It is found that 7 s plasma treatment time for acquiring wettability difference is optimal, which resulted in not only effective splitting of the liquid film but also highly consistent line width with mask. Moreover, low retention force of hydrophobic surface is imperative for self-confinement of the ink into hydrophilic areas, especially for ink with high solid content. The sheet resistance of patterns can reach 5 Ω ◻ −1 after 980 nm laser sintering when using 50 wt% solid content ink with 110 cP viscosity. The geometries of line patterns, i.e., line width and spacing, can be readily tuned by varying the designed size of mask patterns. As-prepared conductive patterns show good conductivity even after 500 bending cycles at 2 mm bending radius. It is believed that this study will provide deeper understanding of wettability difference-assisted patterning process and represents a general strategy for selective wetting, especially for high viscosity ink.
|
|
| 3. |
- Akiyama, Kazunori, et al.
(författare)
-
First M87 Event Horizon Telescope Results. VII. Polarization of the Ring
- 2021
-
Ingår i: Astrophysical Journal Letters. - : American Astronomical Society. - 2041-8213 .- 2041-8205. ; 910:1
-
Tidskriftsartikel (refereegranskat)abstract
- In 2017 April, the Event Horizon Telescope (EHT) observed the near-horizon region around the supermassive black hole at the core of the M87 galaxy. These 1.3 mm wavelength observations revealed a compact asymmetric ring-like source morphology. This structure originates from synchrotron emission produced by relativistic plasma located in the immediate vicinity of the black hole. Here we present the corresponding linear-polarimetric EHT images of the center of M87. We find that only a part of the ring is significantly polarized. The resolved fractional linear polarization has a maximum located in the southwest part of the ring, where it rises to the level of similar to 15%. The polarization position angles are arranged in a nearly azimuthal pattern. We perform quantitative measurements of relevant polarimetric properties of the compact emission and find evidence for the temporal evolution of the polarized source structure over one week of EHT observations. The details of the polarimetric data reduction and calibration methodology are provided. We carry out the data analysis using multiple independent imaging and modeling techniques, each of which is validated against a suite of synthetic data sets. The gross polarimetric structure and its apparent evolution with time are insensitive to the method used to reconstruct the image. These polarimetric images carry information about the structure of the magnetic fields responsible for the synchrotron emission. Their physical interpretation is discussed in an accompanying publication.
|
|
| 4. |
- Farah, Joseph, et al.
(författare)
-
Selective Dynamical Imaging of Interferometric Data
- 2022
-
Ingår i: Astrophysical Journal Letters. - : American Astronomical Society. - 2041-8213 .- 2041-8205. ; 930:2
-
Tidskriftsartikel (refereegranskat)abstract
- Recent developments in very long baseline interferometry (VLBI) have made it possible for the Event Horizon Telescope (EHT) to resolve the innermost accretion flows of the largest supermassive black holes on the sky. The sparse nature of the EHT's (u, v)-coverage presents a challenge when attempting to resolve highly time-variable sources. We demonstrate that the changing (u, v)-coverage of the EHT can contain regions of time over the course of a single observation that facilitate dynamical imaging. These optimal time regions typically have projected baseline distributions that are approximately angularly isotropic and radially homogeneous. We derive a metric of coverage quality based on baseline isotropy and density that is capable of ranking array configurations by their ability to produce accurate dynamical reconstructions. We compare this metric to existing metrics in the literature and investigate their utility by performing dynamical reconstructions on synthetic data from simulated EHT observations of sources with simple orbital variability. We then use these results to make recommendations for imaging the 2017 EHT Sgr A* data set.
|
|
| 5. |
- Narayan, Ramesh, et al.
(författare)
-
The Polarized Image of a Synchrotron-emitting Ring of Gas Orbiting a Black Hole
- 2021
-
Ingår i: Astrophysical Journal. - : American Astronomical Society. - 1538-4357 .- 0004-637X. ; 912:1
-
Tidskriftsartikel (refereegranskat)abstract
- Synchrotron radiation from hot gas near a black hole results in a polarized image. The image polarization is determined by effects including the orientation of the magnetic field in the emitting region, relativistic motion of the gas, strong gravitational lensing by the black hole, and parallel transport in the curved spacetime. We explore these effects using a simple model of an axisymmetric, equatorial accretion disk around a Schwarzschild black hole. By using an approximate expression for the null geodesics derived by Beloborodov and conservation of the Walker-Penrose constant, we provide analytic estimates for the image polarization. We test this model using currently favored general relativistic magnetohydrodynamic simulations of M87*, using ring parameters given by the simulations. For a subset of these with modest Faraday effects, we show that the ring model broadly reproduces the polarimetric image morphology. Our model also predicts the polarization evolution for compact flaring regions, such as those observed from Sgr A* with GRAVITY. With suitably chosen parameters, our simple model can reproduce the EVPA pattern and relative polarized intensity in Event Horizon Telescope images of M87*. Under the physically motivated assumption that the magnetic field trails the fluid velocity, this comparison is consistent with the clockwise rotation inferred from total intensity images.
|
|
| 6. |
- Wielgus, Maciek, et al.
(författare)
-
Monitoring the Morphology of M87* in 2009-2017 with the Event Horizon Telescope
- 2020
-
Ingår i: Astrophysical Journal. - : American Astronomical Society. - 1538-4357 .- 0004-637X. ; 901:1
-
Tidskriftsartikel (refereegranskat)abstract
- The Event Horizon Telescope (EHT) has recently delivered the first resolved images of M87*, the supermassive black hole in the center of the M87 galaxy. These images were produced using 230 GHz observations performed in 2017 April. Additional observations are required to investigate the persistence of the primary image feature-a ring with azimuthal brightness asymmetry-and to quantify the image variability on event horizon scales. To address this need, we analyze M87* data collected with prototype EHT arrays in 2009, 2011, 2012, and 2013. While these observations do not contain enough information to produce images, they are sufficient to constrain simple geometric models. We develop a modeling approach based on the framework utilized for the 2017 EHT data analysis and validate our procedures using synthetic data. Applying the same approach to the observational data sets, we find the M87* morphology in 2009-2017 to be consistent with a persistent asymmetric ring of similar to 40 mu as diameter. The position angle of the peak intensity varies in time. In particular, we find a significant difference between the position angle measured in 2013 and 2017. These variations are in broad agreement with predictions of a subset of general relativistic magnetohydrodynamic simulations. We show that quantifying the variability across multiple observational epochs has the potential to constrain the physical properties of the source, such as the accretion state or the black hole spin.
|
|
| 7. |
- Li, Jiantong, et al.
(författare)
-
Ink-jet printed thin-film transistors with carbon nanotube channels shaped in long strips
- 2011
-
Ingår i: Journal of Applied Physics. - : AIP Publishing. - 0021-8979 .- 1089-7550. ; 109:8, s. 084915-
-
Tidskriftsartikel (refereegranskat)abstract
- The present work reports on the development of a class of sophisticated thin-film transistors (TFTs) based on ink-jet printing of pristine single-walled carbon nanotubes (SWCNTs) for the channel formation. The transistors are manufactured on oxidized silicon wafers and flexible plastic substrates at ambient conditions. For this purpose, ink-jet printing techniques are developed with the aim of high-throughput production of SWCNT thin-film channels shaped in long strips. Stable SWCNT inks with proper fluidic characteristics are formulated by polymer addition. The present work unveils, through Monte Carlo simulations and in light of heterogeneous percolation, the underlying physics of the superiority of long-strip channels for SWCNT TFTs. It further predicts the compatibility of such a channel structure with ink-jet printing, taking into account the minimum dimensions achievable by commercially available printers. The printed devices exhibit improved electrical performance and scalability as compared to previously reported ink-jet printed SWCNT TFTs. The present work demonstrates that ink-jet printed SWCNT TFTs of long-strip channels are promising building blocks for flexible electronics.
|
|
| 8. |
- Akiyama, Kazunori, et al.
(författare)
-
First Sagittarius A* Event Horizon Telescope Results. III. Imaging of the Galactic Center Supermassive Black Hole
- 2022
-
Ingår i: Astrophysical Journal Letters. - : American Astronomical Society. - 2041-8213 .- 2041-8205. ; 930:2
-
Tidskriftsartikel (refereegranskat)abstract
- We present the first event-horizon-scale images and spatiotemporal analysis of Sgr A* taken with the Event Horizon Telescope in 2017 April at a wavelength of 1.3 mm. Imaging of Sgr A* has been conducted through surveys over a wide range of imaging assumptions using the classical CLEAN algorithm, regularized maximum likelihood methods, and a Bayesian posterior sampling method. Different prescriptions have been used to account for scattering effects by the interstellar medium toward the Galactic center. Mitigation of the rapid intraday variability that characterizes Sgr A* has been carried out through the addition of a "variability noise budget" in the observed visibilities, facilitating the reconstruction of static full-track images. Our static reconstructions of Sgr A* can be clustered into four representative morphologies that correspond to ring images with three different azimuthal brightness distributions and a small cluster that contains diverse nonring morphologies. Based on our extensive analysis of the effects of sparse (u, v)-coverage, source variability, and interstellar scattering, as well as studies of simulated visibility data, we conclude that the Event Horizon Telescope Sgr A* data show compelling evidence for an image that is dominated by a bright ring of emission with a ring diameter of similar to 50 mu as, consistent with the expected "shadow" of a 4 x 10(6) M (circle dot) black hole in the Galactic center located at a distance of 8 kpc.
|
|
| 9. |
- Broderick, Avery E., et al.
(författare)
-
Characterizing and Mitigating Intraday Variability: Reconstructing Source Structure in Accreting Black Holes with mm-VLBI
- 2022
-
Ingår i: Astrophysical Journal Letters. - : American Astronomical Society. - 2041-8213 .- 2041-8205. ; 930:2
-
Tidskriftsartikel (refereegranskat)abstract
- The extraordinary physical resolution afforded by the Event Horizon Telescope has opened a window onto the astrophysical phenomena unfolding on horizon scales in two known black holes, M87* and Sgr A*. However, with this leap in resolution has come a new set of practical complications. Sgr A* exhibits intraday variability that violates the assumptions underlying Earth aperture synthesis, limiting traditional image reconstruction methods to short timescales and data sets with very sparse (u, v) coverage. We present a new set of tools to detect and mitigate this variability. We develop a data-driven, model-agnostic procedure to detect and characterize the spatial structure of intraday variability. This method is calibrated against a large set of mock data sets, producing an empirical estimator of the spatial power spectrum of the brightness fluctuations. We present a novel Bayesian noise modeling algorithm that simultaneously reconstructs an average image and statistical measure of the fluctuations about it using a parameterized form for the excess variance in the complex visibilities not otherwise explained by the statistical errors. These methods are validated using a variety of simulated data, including general relativistic magnetohydrodynamic simulations appropriate for Sgr A* and M87*. We find that the reconstructed source structure and variability are robust to changes in the underlying image model. We apply these methods to the 2017 EHT observations of M87*, finding evidence for variability across the EHT observing campaign. The variability mitigation strategies presented are widely applicable to very long baseline interferometry observations of variable sources generally, for which they provide a data-informed averaging procedure and natural characterization of inter-epoch image consistency.
|
|
| 10. |
- Eatough, Ralph P., et al.
(författare)
-
Verification of Radiative Transfer Schemes for the EHT
- 2020
-
Ingår i: Astrophysical Journal. - : American Astronomical Society. - 1538-4357 .- 0004-637X. ; 897:2
-
Tidskriftsartikel (refereegranskat)abstract
- The Event Horizon Telescope (EHT) Collaboration has recently produced the first resolved images of the central supermassive black hole in the giant elliptical galaxy M87. Here we report on tests of the consistency and accuracy of the general relativistic radiative transfer codes used within the collaboration to model M87∗ and Sgr A∗. We compare and evaluate (1) deflection angles for equatorial null geodesics in a Kerr spacetime; (2) images calculated from a series of simple, parameterized matter distributions in the Kerr metric using simplified emissivities and absorptivities; (3) for a subset of codes, images calculated from general relativistic magnetohydrodynamics simulations using different realistic synchrotron emissivities and absorptivities; (4) observables for the 2017 configuration of EHT, including visibility amplitudes and closure phases. The error in total flux is of order 1% when the codes are run with production numerical parameters. The dominant source of discrepancies for small camera distances is the location and detailed setup of the software "camera"that each code uses to produce synthetic images. We find that when numerical parameters are suitably chosen and the camera is sufficiently far away the images converge and that for given transfer coefficients, numerical uncertainties are unlikely to limit parameter estimation for the current generation of EHT observations. The purpose of this paper is to describe a verification and comparison of EHT radiative transfer codes. It is not to verify EHT models more generally.
|
|
