| 1. |
- Blanco, A., et al.
(author)
-
Performance of timing resistive plate chambers with relativistic neutrons from 300 to 1500 MeV
- 2015
-
In: Journal of Instrumentation. - : IOP Publishing. - 1748-0221. ; 10:2
-
Journal article (peer-reviewed)abstract
- A prototype composed of four resistive plate chamber layers has been exposed to quasi-monoenergetic neutrons produced from a deuteron beam of varying energy (300 to 1500 AMeV) in experiment S406 at GSI, Darmstad, Germany. Each layer, with an active area of about 2000 × 500 mm2, is made of modules containing the active gaps, all in multigap construction. Each gap is defined by 0.3 mm nylon mono-filaments positioned between 2.85 mm thick float glass electrodes. The modules are operated in avalanche mode with a non-flammable gas mixture composed of 90% C2H2F4 and 10% SF6. The signals are readout by a pick-up electrode formed by 15 copper strips (per layer), spaced at a pitch of 30 mm, connected at both sides to timing front end electronics. Measurements of the time of flight jitter of neutrons, in the mentioned energy range, point to a contribution of the resistive plate chamber in the order of 150 ps, independent of the neutron energy.
|
|
| 2. |
- Ge, Yu, 1995, et al.
(author)
-
Experimental Validation of Single BS 5G mmWave Positioning and Mapping for Intelligent Transport
- 2024
-
In: IEEE Transactions on Vehicular Technology. - 0018-9545 .- 1939-9359. ; In Press
-
Journal article (peer-reviewed)abstract
- Positioning with 5G signals generally requires connection to several base stations (BSs), which makes positioning more demanding in terms of infrastructure than communications. To address this issue, there have been several theoretical studies on single BS positioning, leveraging high-resolution angle and delay estimation and multipath exploitation possibilities at mmWave frequencies. This paper presents the first realistic experimental validation of such studies, involving a commercial 5G mmWave BS with a customized beam sweep procedure and a user equipment (UE) development kit mounted on a test vehicle. We present the relevant signal models, and signal processing methods, and validate these based on data collected in an outdoor science park environment. Our results indicate that positioning is possible, but the performance is limited by the knowledge of the position and orientation of the infrastructure and the multipath visibility and diversity
|
|
| 3. |
- Ge, Yu, 1995, et al.
(author)
-
Experimental Validation of Single Base Station 5G mm Wave Positioning: Initial Findings
- 2022
-
In: 2022 25th International Conference on Information Fusion, FUSION 2022. - Piscataway : IEEE.
-
Conference paper (peer-reviewed)abstract
- 5G cellular networks can utilize millimeter wave signals, and support large bandwidths and large antenna arrays, which provide more geometric-based signals and higher delay and angle resolutions. These merits bring new opportunities in positioning the user with limited infrastructure through the use of combined angle and delay information. However, there are many practical challenges to overcome, in order to have a functioning single base station 5G mmWave positioning system. In this paper, we describe a deployed single base station mmWave positioning system, and provide an example of the measurement data. Furthermore, we perform measurement validation on a limited measurement data set by performing base station localization. Additional evaluations performed on simulation model data provide guidelines on the required size of the data set and receiver antenna configuration, which will be implemented in upcoming measurements.
|
|
| 4. |
- Cosmas, John, et al.
(author)
-
Towards joint communication and sensing (Chapter 4)
- 2023
-
In: Towards Sustainable and Trustworthy 6G: Challenges, Enablers, and Architectural Design. - 9781638282396 ; , s. 121-158
-
Book chapter (other academic/artistic)abstract
- Localization of user equipment (UE) in mobile communication networks has been supported from the early stages of 3rd generation partnership project (3GPP). With 5th Generation (5G) and its target use cases, localization is increasingly gaining importance. Integrated sensing and localization in 6th Generation (6G) networks promise the introduction of more efficient networks and compelling applications to be developed.
|
|
| 5. |
- Momodu, Damilola, et al.
(author)
-
Stable ionic-liquid-based symmetric supercapacitors from Capsicum seed-porous carbons
- 2019
-
In: Journal of Electroanalytical Chemistry. - : Elsevier BV. - 1572-6657. ; 838, s. 119-128
-
Journal article (peer-reviewed)abstract
- In this study, a symmetric ionic-liquid based supercapacitor was assembled with porous carbon derived from Capsicum (bell pepper) seeds. The “peppered”-activated carbon (ppAC) was synthesized using varying amounts of KHCO 3 activating agent (AA) at 850 °C carbonization temperature. The best device performance reported was recorded with optimum amounts of AA to raw material. The need for less amount of AA is crucial if the entire activation/carbonization process is to be scaled-up with the cost and final product yield also being important for a viable synthesis. A mechanism of saturation of pores with unreacted AA which leads to lower porosity metrics in the samples with increasing the amount of AA during carbonization/activation was also proposed. Using an ionic liquid electrolyte, 1-ethyl-3-methylimidazolium bistrifluorosulfonylimide (EMIM-TFSI), the ppAC-based supercapacitor operated up to a maximum cell voltage of 3.20 V. A specific energy of 37 Wh kg −1 was obtainable with a corresponding practical power density of 0.6 kW kg −1 at 0.5 A g −1 . A specific energy of ∼26 Wh kg −1 was still achievable when the applied current was doubled to 1.0 A g −1 and a high cyclic stability (approx. 99% coulombic efficiency) was proven over 25,000 cycles. Further ageing test performed on the device revealed a remarkable improvement in the electrochemical performance after a 180 h (ca. 1 week) floating time. The obtained results also confirmed a uniquely distributed porous carbon in which the complete utilization of the entire less-corrosive KHCO 3 AA for optimal pore activation at elevated carbonization temperatures. Thus, the efficient design combinations for stable, high-energy and power ionic liquid-based supercapacitors with cheaper biomass-based materials are demonstrated.
|
|
| 6. |
- Calcagno, Giulio, 1990, et al.
(author)
-
Fast charging negative electrodes based on anatase titanium dioxide beads for highly stable Li-ion capacitors
- 2020
-
In: Materials Today Energy. - : Elsevier BV. - 2468-6069. ; 16
-
Journal article (peer-reviewed)abstract
- Hybrid energy storage systems aim to achieve both high power and energy densities by combining supercapacitor-type and battery-type electrodes in tandem. The challenge is to find sustainable materials as fast charging negative electrodes, which are characterized by high capacity retention. In this study, mesoporous anatase beads are synthetized with tailored morphology to exploit fast surface redox reactions. The TiO2-based electrodes are properly paired with a commercial activated carbon cathode to form a Li-ion capacitor. The titania electrode exhibits high capacity and rate performance. The device shows extremely stable performance with an energy density of 27 mWh g-1 at a specific current of 2.5 A g−1 for 10,000 cycles. The remarkable stability is associated with a gradual shift of the potential during cycling as result of the formation of cubic LiTiO2 on the surface of the beads. This phenomenon renews the interest in using TiO2 as negative electrode for Li-ion capacitors.
|
|
| 7. |
- Oyedotun, Kabir O., et al.
(author)
-
Comparison of ionic liquid electrolyte to aqueous electrolytes on carbon nanofibres supercapacitor electrode derived from oxygen-functionalized graphene
- 2019
-
In: Chemical Engineering Journal. - : Elsevier BV. - 1385-8947. ; 375
-
Journal article (peer-reviewed)abstract
- A facial force-driven reflux technique was used to develop fibre-like carbon material from freeze-dried reduced graphene oxide (RGO) firstly prepared by using a modified Hummers method. The carbon nanofibres displayed a high specific surface area of ∼1317.8 m2 g−1, with good pore size distributions which could be beneficial for energy storage applications. Electrochemical measurements of the carbon nanofibre electrodes in a symmetric configuration with aqueous (1 M Na2SO4, 6 M KOH), and protic ionic liquid (1-ethylimidazolium bis(trifluoromethanesulfonly)imide) electrolytes (ILE) displayed excellent electrochemical performance with the dominant electric double layer capacitor (EDLC) behaviour. The fabricated device shows higher electrochemical performance in the ILE due to its larger cell operating potential (3.0 V) as compared with the aqueous electrolytes (0.8 V). The optimized electrochemical properties especially in terms of higher specific energy and superior stability, suggest the material's potential applications as electrode for supercapacitors.
|
|
