| 1. |
- Li, Mengxiong, et al.
(författare)
-
Highly Oriented Graphite Aerogel Fabricated by Confined Liquid-Phase Expansion for Anisotropically Thermally Conductive Epoxy Composites
- 2020
-
Ingår i: ACS Applied Materials & Interfaces. - : American Chemical Society (ACS). - 1944-8252 .- 1944-8244. ; 12:24, s. 27476-27484
-
Tidskriftsartikel (refereegranskat)abstract
- Graphene-based thermally conductive polymer composites are of great importance for the removal of the excess heat generated by electronic devices. However, due to the orientation of graphene sheets in the polymer matrix, the through-plane thermal conductivity of polymer/graphene composites remains far from satisfactory. We here demonstrate a confined liquid-phase expansion strategy to fabricate highly oriented confined expanded graphite (CEG) aerogels. After being incorporated into epoxy resin (EP), the resulting EP/CEG composites exhibit a high through-plane thermal conductivity (4.14 ± 0.21 W m-1 K-1) at a quite low filler loading of 1.75 wt % (0.91 vol %), nearly 10 times higher than that of neat EP resin and 7.5 times higher than the in-plane thermal conductivity of the composite, indicating that the CEG aerogel has a high through-plane thermal conductivity enhancement efficiency that outperforms those of many graphite/graphene-based fillers. The facile preparation method holds great industrial application potential in fabricating anisotropic thermally conductive polymer composites.
|
|
| 2. |
- Fu, Yifeng, 1984, et al.
(författare)
-
Graphene related materials for thermal management
- 2020
-
Ingår i: 2D Materials. - : IOP Publishing. - 2053-1583. ; 7:1
-
Tidskriftsartikel (refereegranskat)abstract
- Almost 15 years have gone ever since the discovery of graphene as a single atom layer. Numerous papers have been published to demonstrate its high electron mobility, excellent thermal and mechanical as well as optical properties. We have recently seen more and more applications towards using graphene in commercial products. This paper is an attempt to review and summarize the current status of the research of the thermal properties of graphene and other 2D based materials including the manufacturing and characterization techniques and their applications, especially in electronics and power modules. It is obvious from the review that graphene has penetrated the market and gets more and more applications in commercial electronics thermal management context. In the paper, we also made a critical analysis of how mature the manufacturing processes are; what are the accuracies and challenges with the various characterization techniques and what are the remaining questions and issues left before we see further more applications in this exciting and fascinating field.
|
|
| 3. |
- Khoshnevisan, Benyamin, et al.
(författare)
-
A critical review on livestock manure biorefinery technologies : Sustainability, challenges, and future perspectives
- 2021
-
Ingår i: Renewable & sustainable energy reviews. - : Elsevier. - 1364-0321 .- 1879-0690. ; 135
-
Tidskriftsartikel (refereegranskat)abstract
- An ever increasing demand for animal protein products has posed serious challenges for managing the increasingquantities of livestock manure. The choice of treatment technologies is still a complicated task and considerabledebates over this issue still continue. To build a clearer picture of manure treatment framework, this study wasconducted to review the most frequently employed manure management technologies from their state of the art,challenges, sustainability, environmental regulations and incentives, and improvement strategies perspectives.The results showed that most treatment technologies have focused on the solid fraction of manure while theliquid fraction still remains a potential environmental threat. Compared to other waste to energy solutions,anaerobic digestion is the most mature technology to upgrade manure’s organic matter into renewable energy,however the problems associated with high investment costs, operating parameters, manure collection, anddigestate management have hindered its developments in rural areas in developing countries. Bio-oil productionthrough hydrothermal liquification is also a promising solution, as it can directly convert the wet manure intobiofuel. However, lipid-poor nature of manure, operational difficulties, and the need for downstream process toremove nitrogenous compounds from the final product necessitate further research. Livestock manure management(both solid and liquid fractions) under biorefinery approach seems an inevitable solution for futuresustainable development to meet circular bioeconomy requirements. Much research is still required to establish asystematic framework based on regional requirements to develop an integrated manure nutrient recycling andmanure management planning with minimum environmental risks and maximum profit.
|
|
| 4. |
- Liu, Lianhua, et al.
(författare)
-
Heavy metal accumulation, geochemical fractions, and loadings in two agricultural watersheds with distinct climate conditions
- 2020
-
Ingår i: Journal of Hazardous Materials. - : Elsevier. - 0304-3894 .- 1873-3336. ; 389
-
Tidskriftsartikel (refereegranskat)abstract
- The main aim of this study was to explore the effects of climate conditions on the transport and transformation of heavy metals. Sedimentary geochemical analysis and watershed modeling were used to investigate the distinctions between heavy metal pollution under different climate conditions. The results showed that the average concentrations of Cu, Cd, and Pb in sediments of the subtropical watershed (36.64, 0.60, and 133.69 mg/kg, respectively) were higher than those of the temperate watershed (26.58, 0.19, and 23.17 mg/kg, respectively) because of surface runoff-induced heavy metal loadings under higher precipitation. Also, the labile fractions, which mainly originated from anthropogenic sources, showed higher percentages in the subtropical watershed (67.84-91.33%), thereby indicating that the transport of heavy metals was promoted by surface runoff. Moreover, higher percentages of acid-soluble fractions of Cu and Pb (23.55-33.60%) in the subtropical watershed suggested that higher temperatures accelerated the transformation of heavy metal fractions, thus contributing to the transportation of heavy metals. Overall, climate conditions were the dominant factors for the differences between the subtropical and temperate watersheds. The results of this study suggest that the effects of climate conditions on the transport, enrichment, and bioavailability of heavy metals are of great significance. Such effects should therefore be the focus of future studies.
|
|
| 5. |
- Liu, Wei, et al.
(författare)
-
Microencapsulated phase change material through cellulose nanofibrils stabilized Pickering emulsion templating
- 2023
-
Ingår i: advanced composites and hybrid materials. - 2522-0128. ; 6:4
-
Tidskriftsartikel (refereegranskat)abstract
- Phase change materials (PCMs) possess remarkable capability to store and release substantial amounts of energy during the processes of melting and crystallization across a wide temperature range, thus holding great promise in applications related to temperature regulation and thermal energy storage. Herein, to effectively address PCM leakage and enhance thermal conduction, PCM microcapsules with melamine-formaldehyde resin (MF) shell were prepared using in situ polymerization of Pickering emulsions stabilized by cellulose nanofibrils (CNFs). CNFs were selected as the stabilizers for the Pickering emulsions and as reinforcing nanofillers for the MF shell, owing to their excellent emulsifying capability, high mechanical strength, and sustainable nature. Paraffin wax (PW) was utilized as the PCM material. The resulting PCM microcapsules with MF resin shells and PW core had a diameter ranging from 2 to 4 & mu;m. Results showed that microcapsule with the core-shell ratio of 2 (Micro-2.0) exhibited the highest latent heat of crystallization and latent heat of fusion, measuring approximately 128.40 J/g and 120.23 J/g, respectively. The encapsulation efficiency of Micro-2.0 was determined to be approximately 79.84%.
|
|
| 6. |
- Liu, Ya, 1991, et al.
(författare)
-
A Novel Graphene Quantum Dot-Based mRNA Delivery Platform
- 2021
-
Ingår i: ChemistryOpen. - : Wiley. - 2191-1363. ; 10:7, s. 666-671
-
Tidskriftsartikel (refereegranskat)abstract
- During the last decades, there has been growing interest in using therapeutic messager RNA (mRNA) together with drug delivery systems. Naked, unformulated mRNA is, however, unable to cross the cell membrane and is susceptible to degradation. Here we use graphene quantum dots (GQDs) functionalized with polyethyleneimine (PEI) as a novel mRNA delivery system. Our results show that these modified GQDs can be used to deliver intact and functional mRNA to Huh-7 hepatocarcinoma cells at low doses and, that the GQDs are not toxic, although cellular toxicity is a problem for these first-generation modified particles. Functionalized GQDs represent a potentially interesting delivery system that is easy to manufacture, stable and effective.
|
|
| 7. |
- Liu, Ya, 1991, et al.
(författare)
-
Egg albumen templated graphene foams for high-performance supercapacitor electrodes and electrochemical sensors
- 2018
-
Ingår i: Journal of Materials Chemistry A. - : Royal Society of Chemistry (RSC). - 2050-7488 .- 2050-7496. ; 6:37, s. 18267-18275
-
Tidskriftsartikel (refereegranskat)abstract
- We demonstrate a simple and scalable strategy to obtain N, S and Si co-doped biocompatible graphene foams (GFs) with different shapes using egg albumen as the template. The unique porous structure and element doping endow the GFs with a high charge-discharge rate and good wettability, which largely improve the electrochemical performance of the electrodes, including ultrahigh specific capacitance (534 F g-1at 1 A g-1), and excellent rate capability (308 F g-1at 100 A g-1) and cycling performance (96.1% retention of the initial capacitance after 10000 cycles at a high current density of 10 A g-1). Besides, when used as an electrochemical sensor for dopamine, the GF exhibits a detection limit as low as 1.2 μM with a linear response up to 70 μM, due to the low equivalent series resistance. These reveal great potential for promoting the application of 3D graphene in energy storage and electrochemical sensors.
|
|
| 8. |
- Liu, Ya, 1991, et al.
(författare)
-
Surface modification of graphene for use as a structural Fortifier in water-borne epoxy coatings
- 2019
-
Ingår i: Coatings. - : MDPI AG. - 2079-6412. ; 9:11
-
Tidskriftsartikel (refereegranskat)abstract
- Graphene, the typical two-dimensional sp2 hybridized carbon allotrope, is widely used as a filler for improving the mechanical performance of polymers. However, its superhydrophobic surface makes it a big challenge to obtain stable graphene dispersions, especially in water-borne systems. On the contrary, graphene oxide (GO) shows excellent dispersibility in water, but strong oxidants and acids destroy its structure and degrade its mechanical properties. This largely limits its application in water-borne coatings. In this work, graphene from mechanical exfoliation was surface modified by p-aminophenol derived diazonium salt to achieve a homogenous dispersion. Moreover, the hydroxyl groups in p-aminophenol are able to combine with epoxy resins during the curing process to improve mechanical performance of the final coatings. The result shows that functionalized graphene shows a lower coefficient of friction and better abrasion resistance compared to GO.
|
|
| 9. |
- Liu, Ya, 1991, et al.
(författare)
-
Thermally Conductive and Electrically Insulating PVP/Boron Nitride Composite Films for Heat Spreader
- 2019
-
Ingår i: Advancing Microelectronics. - 2222-8748. ; 2019:NOR, s. 1-5
-
Tidskriftsartikel (refereegranskat)abstract
- Thermally conductive materials with electrically insulating properties have been extensively investigated for thermal management of electronic devices. The combined properties of high thermal conductivity, structural stability, corrosion resistance and electric resistivity make hexagonal boron nitride (h-BN) a promising candidate for this purpose. Theoretical studies have revealed that h-BN has a high in-plane thermal conductivity up to 400 - 800 W m−1 K−1 at room temperature. However, it is still a big challenge to achieve high thermally conductive h-BN thick films that are commercially feasible due to its poor mechanical properties. On the other hand, many polymers exhibit advantages for flexibility. Thus, combining the merits of polymer and the high thermal conductivity of h-BN particles is considered as a promising solution for this issue. In this work, orientated PVP/h-BN films were prepared by electrospinning and a subsequent mechanical pressing process. With the optimized h-BN loading, a PVP/h-BN composite film with up to 22 W m-1 K-1 and 0.485 W m-1 K-1 for in-plane and through-plane thermal conductivity can be achieved, respectively. We believe this work can help accelerate the development of h-BN for thermal management applications.
|
|
| 10. |
- An, Hongbin, et al.
(författare)
-
A method of manufacturing microfluidic contact lenses by using irreversible bonding and thermoforming
- 2018
-
Ingår i: Journal of Micromechanics and Microengineering. - : IOP PUBLISHING LTD. - 0960-1317 .- 1361-6439. ; 28:10
-
Tidskriftsartikel (refereegranskat)abstract
- In this paper, we present the development of microfluidic contact lenses, which is based on the advantages of wearable microfluidics and can have great potential in the ophthalmology healthcare field. The development consists of two parts; the manufacturing process and the usability tests of the devices. In the manufacturing process, we firstly extended silane coupling and surface modification to irreversibly bond plastic membranes with microchannel-molded silicone rubber, to form the plastic-PDMS plane assemblies, and then molded the plane into a contact lens by thermoforming. We systematically investigated the effects of thermoforming factors, heating temperatures and the terrace die's sphere radius on channels by using the factorial experiment design. In addition, various tests were conducted to verify the usability of the devices. Through blockage and leakage tests, the devices were proved to be feasible, with no channel-blockages and could stand high pressures. Through a wearing test, the contact lenses were confirmed to be harmless on the living body. Furthermore, by performing the manipulating test, the device was proved to be liquid-controllable. These works provide a foundation for the applications of microfluidic contact lenses in ophthalmology.
|
|
