| 1. |
- Zhang, Dongsheng, et al.
(författare)
-
Thermal properties of TIM using CNTs forest in electronics packaging
- 2016
-
Ingår i: 2016 17th International Conference on Electronic Packaging Technology, ICEPT 2016; Wuhan Optics Valley Kingdom Hotel Wuhan; China; 16 August 2016 through 19 August 2016. ; , s. 1355-1359
-
Konferensbidrag (refereegranskat)abstract
- Thermal interface material (TIM) is applied to fill the air gaps of interfaces, which provides a path for interfacial heat transfer. Owing to the exceptional thermal properties of carbon nanotubes (CNT), TIMs based on CNTs have received much attention in recent years. In this study, heat dissipation performance of vertically aligned carbon nanotubes (VACNT) arrays as TIM in electronic packing was analyzed. Vertically aligned carbon nanotubes with length of 245?m and 763?m were synthesized on a silicon substrate by chemical vapor deposition respectively. Morphology of the vertically aligned carbon nanotubes was characterized by scanning electron microscope. The hotspot temperature of thermal test chip with vertically aligned carbon nanotubes were characterized by resistance temperature detector method and infrared imaging method.
|
|
| 2. |
- Bao, Jie, et al.
(författare)
-
Application of two-dimensional layered hexagonal boron nitride in chip cooling
- 2016
-
Ingår i: Yingyong Jichu yu Gongcheng Kexue Xuebao/Journal of Basic Science and Engineering. - 1005-0930. ; 24:1, s. 210-217
-
Tidskriftsartikel (refereegranskat)abstract
- © 2016, The Editorial Board of Journal of Basic Science and Engineering. All right reserved.Research into layered hexagonal boron nitride(h-BN)has recently intensified, due to its superior physicochemical properties compared to that of a typical two-dimensional material. H-BN can be utilized in power chips as both an insulating layer as well as a heat spreader for local hotspots with high heat flux. Single layer h-BN film grown by CVD and h-BN microparticles are respectively transferred onto the surfaces of the thermal evaluation chips, where the influence of h-BN on the heat dissipation performance of the chips can be observed at different power values. The resistance-temperature curve method and infrared thermal imager are both used to measure the temperature of hotspots on the thermal evaluation chips, which can be reduced by between 3~5℃ at 1W after the transfer of h-BN. The cooling efficiency is improved and it can be found that single layer h-BN film shows better heat dissipation ability.
|
|
| 3. |
- Bao, Jie, et al.
(författare)
-
Measurement of Dielectric Properties of Ultrafine BaTiO3 Using an Organic-Inorganic Composite Method
- 2015
-
Ingår i: Journal of Electronic Materials. - : Springer Science and Business Media LLC. - 1543-186X .- 0361-5235. ; 44:7, s. 2300-2307
-
Tidskriftsartikel (refereegranskat)abstract
- Ultrafine BaTiO3, unlike traditional ferroelectric materials, demonstrates some interesting dielectric properties, such as a gradual transition from paraelectric to ferroelectric phase, which is similar to dielectric relaxation ferroelectrics. Although several methods have been recently proposed to measure the dielectric properties of ultrafine BaTiO3, the problem still remains unsolved. This paper proposes a new method to estimate the dielectric properties of ultrafine BaTiO3 by measuring and analyzing the dielectric properties of BaTiO3-epoxy composites. The Novocontrol dielectric measuring system was employed to measure the dielectric response of the composites. The dielectric behavior and relaxation characteristics of the BaTiO3 filler were estimated by modeling and calculating the dielectric constant based on different mixture theories. Results reveal that the effect of surface states yields dielectric relaxation in ultrafine BaTiO3.
|
|
| 4. |
- Bao, Jie, et al.
(författare)
-
Synthesis and Applications of Two-Dimensional Hexagonal Boron Nitride in Electronics Manufacturing
- 2016
-
Ingår i: Electronic Materials Letters. - : Springer Science and Business Media LLC. - 1738-8090 .- 2093-6788. ; 12:1, s. 1-16
-
Forskningsöversikt (refereegranskat)abstract
- In similarity to graphene, two-dimensional (2D) hexagonal boron nitride (hBN) has some remarkable properties, such as mechanical robustness and high thermal conductivity. In addition, hBN has superb chemical stability and it is electrically insulating. 2D hBN has been considered a promising material for many applications in electronics, including 2D hBN based substrates, gate dielectrics for graphene transistors and interconnects, and electronic packaging insulators. This paper reviews the synthesis, transfer and fabrication of 2D hBN films, hBN based composites and hBN-based van der Waals heterostructures. In particular, this review focuses on applications in manufacturing electronic devices where the insulating and thermal properties of hBN can potentially be exploited. 2D hBN and related composite systems are emerging as new and industrially important materials, which could address many challenges in future complex electronics devices and systems.
|
|
| 5. |
- Bao, Jie, 1982, et al.
(författare)
-
Two-dimensional hexagonal boron nitride as lateral heat spreader in electrically insulating packaging
- 2016
-
Ingår i: Journal of Physics D: Applied Physics. - : IOP Publishing. - 1361-6463 .- 0022-3727. ; 49:July 2016, s. 265501-
-
Tidskriftsartikel (refereegranskat)abstract
- The need for electrically insulating materials with a high in-plane thermal conductivity for lateral heat spreading applications in electronic devices has intensified studies of layered hexagonal boron nitride (h-BN) films. Due to its physicochemical properties, h-BN can be utilised in power dissipating devices such as an electrically insulating heat spreader material for laterally redistributing the heat from hotspots caused by locally excessive heat flux densities. In this study, two types of boron nitride based heat spreader test structures have been assembled and evaluated for heat dissipation. The test structures separately utilised a few-layer h-BN film with and without graphene enhancement drop coated onto the hotspot test structure. The influence of the h-BN heat spreader films on the temperature distribution across the surface of the hotspot test structure was studied at a range of heat flux densities through the hotspot. It was found that the graphene-enhanced h-BN film reduced the hotspot temperature by about 8–10°C at a 1000 W/cm2 heat flux density, a temperature decrease significantly larger than for h-BN film without graphene enhancement. Finite element simulations of the h-BN film predict that further improvements in heat spreading ability are possible if the thermal contact resistance between the film and test chip are minimised.
|
|
| 6. |
- Edwards, Michael, 1986, et al.
(författare)
-
Finite element simulation of 2D-based materials as heat spreaders
- 2016
-
Ingår i: IMAPS Nordic Annual Conference 2016 Proceedings. - 9781510827226
-
Konferensbidrag (refereegranskat)abstract
- Since the discovery of graphene, the first discovered 2D material, by Novoselov and Geim in 2004, the field of 2D materials has taken off and about 20 further 2D materials have been found. One of the most promising of these materials for the passive cooling of chips is hBN. HBN has the very unusual combination of being electrically insulating and thermally conductive, which potentially makes it an ideal material for both laterally spreading heat and passivating hotspots on chips. This gives hBN an advantage over graphene, where the chip requires a SiO2 passivation layer to prevent short circuits. To help evaluate the performance of these heat spreading films, a finite element model has been devised to support the experimental work undertaken in various publications. This model has been validated with experimental data and suggests that both graphene-And hBN-based materials have significant potential in lateral heat spreading applications.
|
|
| 7. |
- Huang, S., et al.
(författare)
-
Improved reliability of electrically conductive adhesives joints on Cu-Plated PCB substrate enhanced by graphene protection barrier
- 2017
-
Ingår i: 2017 IMAPS Nordic Conference on Microelectronics Packaging, NordPac 2017, Goteborg, Sweden, 18-20 June 2017. - 9781538630556 ; , s. 143-146
-
Konferensbidrag (refereegranskat)abstract
- Graphene protection barrier was introduced to the interface between the ECAs and Cu-plated wire to enhance the reliability of the ECAs joints on Cu-Plated PCB substrate due to its excellent properties of impermeability to all gases/salts as well as its thermal/chemical stability. The results of shear test indicated graphene protection barrier can improve the shear strength of the ECAs joints on Cu-plated PCB substrate by almost 22% after 500 hours high temperature and high humidity cyclic test. Characterizations by optical microscope and XPS were further performed to explain the mechanism. To sum up, it can be believed that the graphene protection barrier can dramatically enhance the reliability of the ECAs joints on Cu-Plated PCB substrate.
|
|
| 8. |
- Huang, Shirong, et al.
(författare)
-
Infrared Emissivity Measurement for Vertically Aligned Multiwall Carbon Nanotubes (CNTs) Based Heat Spreader Applied in High Power Electronics Packaging
- 2016
-
Ingår i: 6th Electronic System-integration Technology Conference (ESTC 2016). - 9781509014026 ; , s. Article no 7764696-
-
Konferensbidrag (refereegranskat)abstract
- Vertically-aligned multiwall carbon nanotubes were deposited on silicon substrate by low pressure chemical vapor deposition (LPCVD), which can be utilized as heat spreaders in high power electronic packaging due to their remarkable thermal conductivity. The infrared emissivity of the vertically aligned multiwall carbon nanotubes was then characterized based on the FLIR SC600 infrared imaging system. The average infrared emissivity of the multiwall carbon nanotubes sample was about 0.92, which agrees well with experimental results reported before. Scanning electron microscopy (SEM) images of the multiwall carbon nanotubes were further analyzed to explain its high emissivity, and the reason can be attributed to the homogeneous sparseness and aligned structure of the vertically aligned multiwall carbon nanotubes
|
|
| 9. |
- Huang, Shirong, et al.
(författare)
-
The Effects of Graphene-Based Films as Heat Spreaders for Thermal Management in Electronic Packaging
- 2016
-
Ingår i: 2016 17th International Conference on Electronic Packaging Technology, ICEPT 2016. - 9781509013968 ; , s. Art no 7583272; Pages 889-892
-
Konferensbidrag (refereegranskat)abstract
- Graphene-based films (GBF) were fabricated using a chemical conversion process including graphene oxide (GO) preparation by use of Hummer’s method, graphene oxide reduction using L-ascorbic acid (LAA), and finally film formation by vacuum filtration. GBF is considered as a candidate material for thermal management, i.e. for removing heat from hotspots in power electronic packaging, due to its high thermal conductivity. In this work, the GBF heat spreading performance in 3D TSV packaging was analysed using finite element methods (FEM) implemented in the COMSOL software. Both size effects and the influence of the thermal conductivity of the GBF heat spreader on the thermal performance of the 3D TSV package were evaluated. Furthermore, the size effects of the thermal conductive adhesive (TCA) underfill between the chip and the printed circuit board (PCB) were analysed. The results obtained are critical for proper design of graphene-based lateral heat spreaders in high power electronic packaging.
|
|
| 10. |
- Jeppson, Kjell, 1947, et al.
(författare)
-
Hotspot test structures for evaluating carbon nanotube microfin coolers and graphene-like heat spreaders
- 2016
-
Ingår i: 29th IEEE International Conference on Microelectronic Test Structures (ICMTS), Yokohama, Japan, Mar 28-31, 2016. - 1071-9032. ; , s. 32-36
-
Konferensbidrag (refereegranskat)abstract
- The design, fabrication, and use of a hotspot-producing and temperature-sensing test structure for evaluating the thermal properties of carbon nanotubes, graphene and boron nitride for cooling of electronic devices in applications like 3D integrated chip-stacks, power amplifiers and light-emitting diodes is described. The test structure is a simple meander-shaped metal resistor serving both as the hotspot and the temperature thermo-meter. By use of this test structure, the influence of emerging materials like those mentioned above on the temperature of the hotspot has been evaluated with good accuracy).
|
|
