| 1. |
- Zhang, Q., et al.
(författare)
-
Effect of sintering method on properties of nanosilver paste
- 2017
-
Ingår i: 2017 IMAPS Nordic Conference on Microelectronics Packaging, NordPac 2017, Goteborg, Sweden, 18-20 June 2017. ; , s. 186-189
-
Konferensbidrag (refereegranskat)abstract
- Nanoscale silver paste has a good application prospect in heat dissipation of high-power chips due to the characteristics of low temperature sintering and high temperature service. The properties of the nanosilver paste including thermal conductivity, electrical conductivity, and shear strength are affected greatly by the sintering process. The influence of different sintering methods on the performance of the nanosilver paste was studied in this article. The nanosilver paste with 80.5 wt% nano-scale silver particles, 1.5 wt% submicron-scale SiC particles with Ag coating, 0.9 wt% dispersion agent, 10 wt% organic carrier and 7.1 wt% diluting agent was sintered at 260°C for 30 min with three different methods, heating table sintering, heating furnace sintering, and mixed sintering. The samples obtained by mixed sintering process have higher thermal conductivity than the ones obtained by heating furnace sintering method and heating table sintering method. The effect of sintering methods on shear strength of nanosilver paste was also investigated subsequently. Shear testing equipment was used to measure the shear strength of the samples gained by heating table sintering, heating furnace sintering, and air dry oven sintering. The maximum shear strength was obtained for the samples by heating table sintering method. The shear strength of samples by air dry oven sintering method was the minimum one.
|
|
| 2. |
- Zhang, Q., et al.
(författare)
-
Mechanical property and reliability of bimodal nano-silver paste with Ag-coated SiC particles
- 2019
-
Ingår i: Soldering and Surface Mount Technology. - 1758-6836 .- 0954-0911. ; 31:4, s. 193-202
-
Tidskriftsartikel (refereegranskat)abstract
- © 2019, Emerald Publishing Limited. Purpose: This study aims to develop a bimodal nano-silver paste with improved mechanical property and reliability. Silicon carbide (SiC) particles coated with Ag were introduced in nano-silver paste to improve bonding strength between SiC and Ag particles and enhance high-temperature stability of bimodal nano-silver paste. The effect of sintering parameters such as sintering temperature, sintering time and the proportion of SiC particles on mechanical property and reliability of sintered bimodal nano-silver structure were investigated. Design/methodology/approach: Sandwich structures consist of dummy chips and copper substrates with nickel and silver coating bonded by nano-silver paste were designed for shear testing. Shear strength testing was conducted to study the influence of SiC particles proportions on the mechanical property of sintered nano-silver joints. The reliability of the bimodal nano-silver paste was evaluated experimentally by means of shear test for samples subjected to thermal aging test at 150°C and humidity and temperature testing at 85°C and 85 per cent RH, respectively. Findings: Shear strength was enhanced obviously with the increase of sintering temperature and sintering time. The maximum shear strength was achieved for nano-silver paste sintered at 260°C for 10 min. There was a negative correlation between the proportion of SiC particles and shear strength. After thermal aging testing and humidity and temperature testing for 240 h, the shear strength decreased a little. High-temperature stability and high-hydrothermal stability were improved by the addition of SiC particles. Originality/value: Submicron-scale SiC particles coated with Ag were used as alternative materials to replace part of nano-silver particles to prepare bimodal nano-silver paste due to its high thermal conductivity and excellent mechanical property.
|
|
| 3. |
- Bao, Jie, et al.
(författare)
-
Application of two-dimensional layered hexagonal boron nitride in chip cooling
- 2016
-
Ingår i: Yingyong Jichu yu Gongcheng Kexue Xuebao/Journal of Basic Science and Engineering. - 1005-0930. ; 24:1, s. 210-217
-
Tidskriftsartikel (refereegranskat)abstract
- © 2016, The Editorial Board of Journal of Basic Science and Engineering. All right reserved.Research into layered hexagonal boron nitride(h-BN)has recently intensified, due to its superior physicochemical properties compared to that of a typical two-dimensional material. H-BN can be utilized in power chips as both an insulating layer as well as a heat spreader for local hotspots with high heat flux. Single layer h-BN film grown by CVD and h-BN microparticles are respectively transferred onto the surfaces of the thermal evaluation chips, where the influence of h-BN on the heat dissipation performance of the chips can be observed at different power values. The resistance-temperature curve method and infrared thermal imager are both used to measure the temperature of hotspots on the thermal evaluation chips, which can be reduced by between 3~5℃ at 1W after the transfer of h-BN. The cooling efficiency is improved and it can be found that single layer h-BN film shows better heat dissipation ability.
|
|
| 4. |
- Casa, Marcello, et al.
(författare)
-
Development and characterization of graphene-enhanced thermal conductive adhesives
- 2014
-
Ingår i: 15th International Conference on Electronic Packaging Technology, ICEPT 2014; Wangjiang HotelChengdu; China; 12 August 2014 through 15 August 2014. - 9781479947072 ; :Art. no. 6922700, s. 480-483
-
Konferensbidrag (refereegranskat)abstract
- According to Moore's Laws, complexity and power densities of electronic devices are increased during the last decades, moreover their dimensions are shrinking to nanometers causing hot-spot temperature escalation. Thermal management, therefore, becomes a critical issue for next generation of electronics. This scenario motivates development of novel thermal conductive adhesive (TCA) with enhanced thermal conductivity. Conventional TCAs use polymers as the matrix (base material) and utilize large loading weight fraction of the filler, usually silver particles, to achieve the thermal conductivity of 1-4 W/ m K at room temperature [1]. Lately it was discovered that graphene exhibit superior thermal conductivity [2] even when they are incorporated with matrix materials [3], which offers a potential to develop high thermal conductive graphene-filled compound. In this paper, a new functionalized graphene and its filled TCA have been developed and characterized. Starting from pristine graphite flakes, graphene was prepared through chemical exfoliation and functionalized with a nano silver layer to form a special metal/graphene hybrid material. Moreover, an efficient method to uniformly disperse the nano-scaled graphene hybrid material in silver-epoxy matrix was developed. Cross-section view of SEM has shown a homogeneous component structure, and TGA analysis of hybrid material is given. The developed compound is based on a commercial TCA which is composed with epoxy matrix and micro-sized Ag flakes. Thermal characterization through Laser-flash equipment has indicated that a significant thermal conductivity improvement was achieved through adding functionalized graphene into the material. Different TCA samples with different weight percentages of functionalized graphene ranging from 0 % (reference) to 11.5 % were prepared and tested to study thermal conductivity change. Data show that a thermal conductivity value of 7.6 W/ m K is reached when the graphene/silver percentage is 11.5 % that is almost 4 times higher than our reference.
|
|
| 5. |
- Chen, S., et al.
(författare)
-
An overview of carbon nanotubes based interconnects for microelectronic packaging
- 2017
-
Ingår i: 2017 IMAPS Nordic Conference on Microelectronics Packaging, NordPac 2017, Goteborg, Sweden, 18-20 June 2017. - 9781538630556 ; , s. 113-119
-
Konferensbidrag (refereegranskat)abstract
- Owing to the great demand in more functions and miniaturization in microelectronic packaging, the dimensions of interconnects has decreased extremely, which has resulted in electrical, thermal, and mechanical reliability issues. To address these issues, carbon nanotube (CNT) has been selected as a promising alternative material for the interconnects in packaging due to its large current density, high thermal conductivity, great flexibility, and low coefficient of thermal expansion (CTE). In this paper, the development of CNTs based vertical interconnects was reviewed. However, the resistivity of CNTs based interconnects was much higher than that of copper interconnects. Thus, this review focused on the resistivity of CNTs-based interconnects in different fabrication process and pointed out what improves the resistivity. In the future, CNTs-Cu nanocomposite with unique properties could be the suitable material for bumps to reduce the resistivity of CNTs based bumps further.
|
|
| 6. |
- Fan, X., et al.
(författare)
-
Reliability of carbon nanotube bumps for chip on glass application
- 2014
-
Ingår i: Proceedings of the 5th Electronics System-Integration Technology Conference, ESTC 2014. - 9781479940264 ; , s. Art. no. 6962753-
-
Konferensbidrag (refereegranskat)abstract
- Carbon nanotubes (CNTs) are an ideal candidate material for electronic interconnects due to their extraordinary thermal, electrical and mechanical properties. In this study, densified CNT bumps utilizing the paper-mediated controlled method were applied as the interconnection for chip on glass (COG) applications, and the silicon chip with patterned CNT bumps was then flipped and bonded onto a glass substrate using anisotropic conductive adhesive (ACA) at a bonding pressure of 127.4 Mpa, 170°C for 8 seconds. The electrical properties of the COG were evaluated with the contact resistance of each bump measured using the four-point probe method. Three different structure traces, marked as Trace A, Trace B, and Trace C, were tested, respectively. Thermal cycling (-40 to 85°C, 800 cycles) and damp heat tests (85°C/85% RH, 1000 hours) were also conducted to evaluate the reliability of the CNT-COG structure. The average contact resistance of the samples was recorded during these tests, in which there was no obvious electrical failure observed after both the thermal cycling and damp heat tests. The results of these tests indicated that the COG has good reliability and the CNT bumps have promising potential applications in COG.
|
|
| 7. |
- Fu, Yifeng, 1984, et al.
(författare)
-
Post-Growth Processing of Carbon Nanotubes for Interconnect Applications - A Review
- 2016
-
Ingår i: 2016 6th Electronic System-Integration Technology Conference (Estc). - 9781509014026 ; , s. Article no 7764713-
-
Konferensbidrag (refereegranskat)abstract
- Interconnect is one of the most important functions of packaging technology. It delivers power and signals into and out of electronic systems. The performance and reliability of microsystems are dependent on the interconnect quality. This paper reviews the chip-level interconnects based on carbon nanotubes (CNTs), this includes their applications for both on-chip and off-chip interconnects. Various post-growth processing of CNTs, such as doping, densification, transfer, metallization, etc., for the improvement of their performance will be reviewed.
|
|
| 8. |
- Huang, S., et al.
(författare)
-
Improved reliability of electrically conductive adhesives joints on Cu-Plated PCB substrate enhanced by graphene protection barrier
- 2017
-
Ingår i: 2017 IMAPS Nordic Conference on Microelectronics Packaging, NordPac 2017, Goteborg, Sweden, 18-20 June 2017. - 9781538630556 ; , s. 143-146
-
Konferensbidrag (refereegranskat)abstract
- Graphene protection barrier was introduced to the interface between the ECAs and Cu-plated wire to enhance the reliability of the ECAs joints on Cu-Plated PCB substrate due to its excellent properties of impermeability to all gases/salts as well as its thermal/chemical stability. The results of shear test indicated graphene protection barrier can improve the shear strength of the ECAs joints on Cu-plated PCB substrate by almost 22% after 500 hours high temperature and high humidity cyclic test. Characterizations by optical microscope and XPS were further performed to explain the mechanism. To sum up, it can be believed that the graphene protection barrier can dramatically enhance the reliability of the ECAs joints on Cu-Plated PCB substrate.
|
|
| 9. |
- Jeppson, Kjell, 1947, et al.
(författare)
-
Hotspot test structures for evaluating carbon nanotube microfin coolers and graphene-like heat spreaders
- 2016
-
Ingår i: 29th IEEE International Conference on Microelectronic Test Structures (ICMTS), Yokohama, Japan, Mar 28-31, 2016. - 1071-9032. ; , s. 32-36
-
Konferensbidrag (refereegranskat)abstract
- The design, fabrication, and use of a hotspot-producing and temperature-sensing test structure for evaluating the thermal properties of carbon nanotubes, graphene and boron nitride for cooling of electronic devices in applications like 3D integrated chip-stacks, power amplifiers and light-emitting diodes is described. The test structure is a simple meander-shaped metal resistor serving both as the hotspot and the temperature thermo-meter. By use of this test structure, the influence of emerging materials like those mentioned above on the temperature of the hotspot has been evaluated with good accuracy).
|
|
| 10. |
- Wang, Nan, 1988, et al.
(författare)
-
Development and Characterization of Graphene Enhanced Thermal Conductive Adhesives
- 2016
-
Ingår i: 2016 6th Electronic System-Integration Technology Conference (Estc). - 9781509014026 ; , s. Article no 7764682-
-
Konferensbidrag (refereegranskat)abstract
- In this paper, a graphene enhanced thermal conductive adhesive (G-TCA) was developed for thermal management of power devices. The developed G-TCA has many advantages, including high thermal conductivity, lower density, good dispensing ability. and cost effective. To fabricate G-TCAs. few-layer graphene was utilized as fillers to improve the thermal conductivity of the TCA. The graphene nanosheets were fabricated through a high-speed shear mixing process in a mixed solvent. Compared to many reported liquid exfoliation process, the graphene fabrication process shows many advantages, such as high process efficiency, mass production, low-cost, clean and safe process. G-TCA sample with a hybrid filler ratio of 73% Ag and 3% graphene shows the highest thermal conductivity of 8 W/m K, which is almost four times higher than reference TCAs. A Joule heating setup was built to simulate G-TCA's function in a real electronic component and demonstrate the superior heat dissipation properties of the G-TCAs. Viscosities of the G-TCA samples were regulated in an acceptable range of many dispensing processes to be able to make uniform and fine patterns. Therefore, the developed G-TCA could be widely used for thermal management of power devices and electronic packaging area to decrease their working temperatures and extend the lifetime of devices.
|
|
