↓ Direkt till sidans innehåll
↓ Direkt till sidans sekundära innehåll (sidomenyn)

Tyck till om SwePub Sök här!

Träfflista för sökning "WFRF:(Savage P) ;hsvcat:2"

Sökning: WFRF:(Savage P) > Teknik

Resultat 1-2 av 2

Sortera/gruppera träfflistan

Sortering: Träffar per sida:

Numrering	Referens	Omslagsbild	Hitta
1.	Johansson, Martin L, et al. (författare) Short-term results from seventy-six patients receiving a bone anchored hearing implant installed with a novel minimally invasive surgery technique. 2017 Ingår i: Clinical Otolaryngology. - : Wiley. - 1749-4478 .- 1365-2273. ; 42:5, s. 1043-1048 Tidskriftsartikel (refereegranskat)abstract The surgical installation of bone anchored hearing systems (BAHS) has after decades finally undergone changes towards more minimally invasive techniques without soft tissue thinning. Some surgeons are also performing the surgery and installation, using the classical drilling system, through a single punch entry. This article is protected by copyright. All rights reserved.
2.	Persson, P., et al. (författare) Self-propagating high-temperature synthesis and liquid-phase sintering of TiC/Fe composites 2002 Ingår i: Journal of Materials Processing Technology. - 0924-0136 .- 1873-4774. ; 127:2, s. 131-139 Tidskriftsartikel (refereegranskat)abstract The present paper addresses a possible route for the manufacturing of iron-based metal-matrix composites (MMCs) with a high level of reinforcement. The ceramic reinforcement studied was titanium carbide (TiC). TiC is one of the hardest materials to be found, which is why a TiC/Fe composite has the potential to be used as armour. Two manufacturing routes have been evaluated experimentally, i.e., liquid-phase sintering (LPS) and self-propagating high-temperature synthesis (SHS). LPS was found to be more effective due to easier process control and due to the process yielding a more homogeneous material. Both LPS and SHS produced a material with a relatively high degree of porosity. The porosity in the LPS experiments could be decreased by varying the process parameters, but this was not possible in the SHS process. Metallographic investigation shows that the TiC/Fe system is feasible and that applications utilising TiC/Fe composites are possible in the future. This is due to the fact that despite the porosity, an improvement of the MMC properties is detected, compared to those of the matrix material. © 2002 Elsevier Science B.V. All rights reserved.

Skapa referenser, mejla, bekava och länka

Länka till träfflistan

Resultat 1-2 av 2

Avgränsa träffmängd

Typ av publikation: tidskriftsartikel (2)

Typ av innehåll: refereegranskat (2)

Författare/redaktör: Caruso, A (1); Schart-Moren, Nadine (1); Hultcrantz, M (1); Banerjee, A (1); Persson, P. (1); Cremers, C. W. (1); visa fler...; Savage, S (1); Jarfors, A. E. W. (1); Windfuhr, J.P. (1); van Tongeren, J. (1); Johansson, Martin L (1); Stokroos, R. J. (1); Hof, J. R. (1); Brunings, J. W. (1); Jonhede, S. (1); Holmberg, M. (1); Tysome, J. R. (1); Banga, R (1); Hol, M K (1); Mylanus, E A (1); Savage Jones, H (1); Vannucchi, P (1); Lutgert, R W (1); Giannuzzi, A L (1); Bordin, S (1); Hanif, J (1); Singam, S (1); visa färre...

Lärosäte: Göteborgs universitet (1); Uppsala universitet (1); Jönköping University (1); Karolinska Institutet (1)

Språk: Engelska (2)

Forskningsämne (UKÄ/SCB): Teknik (2)Ta bort avgränsningen; Medicin och hälsovetenskap (1)

År

Kungliga biblioteket hanterar dina personuppgifter i enlighet med EU:s dataskyddsförordning (2018), GDPR. Läs mer om hur det funkar här.
Så här hanterar KB dina uppgifter vid användning av denna tjänst.

Copyright © LIBRIS - Nationella bibliotekssystem
LIBRIS.kb.se

pil uppåt

Stäng

Kopiera och spara länken för att återkomma till aktuell vy