SwePub
Sök i SwePub databas

  Utökad sökning

Träfflista för sökning "WFRF:(Svensson Erik) ;lar1:(cth)"

Sökning: WFRF:(Svensson Erik) > Chalmers tekniska högskola

  • Resultat 1-10 av 384
Sortera/gruppera träfflistan
   
NumreringReferensOmslagsbildHitta
1.
  •  
2.
  • Davidsson, Kent, 1967, et al. (författare)
  • Potassium, chlorine, and sulfur in ash, particles, deposits, and corrosion during wood combustion in a circulating fluidized-bed boiler
  • 2007
  • Ingår i: Energy & Fuels. - : American Chemical Society (ACS). - 1520-5029 .- 0887-0624. ; 21:1, s. 71-81
  • Tidskriftsartikel (refereegranskat)abstract
    • The effect of the addition of chlorine and/or sulfur to the fuel on fly ash composition, deposit formation, and superheater corrosion has been studied during biomass combustion in a circulating fluidized-bed boiler. The chlorine (HCl (aq)) and sulfur (SO2 (g)) were added in proportions of relevance for the potassium chemistry. The composition of the bottom and the fly ashes was analyzed. Gas and particle measurements were performed downstream of the cyclone before the convection pass and the flue gas composition was recorded in the stack with a series of standard instruments and an FTIR analyzer. At the position downstream of the cyclone, a deposit probe was situated, simulating a superheater tube. Deposits on the probe and initial corrosion were examined. It is concluded that addition of sulfur and chlorine increases the formation of submicron particles leading to deposition of potassium sulfate and chloride. The results compare well with earlier work based on laboratory-scale experiments concerning effects of chlorine and sulfur on potassium chemistry.
  •  
3.
  • Folkeson, Nicklas, 1981, et al. (författare)
  • Fireside corrosion of stainless and low alloyed steels in a waste-fired CFB boiler; The effect of adding sulphur to the fuel
  • 2008
  • Ingår i: Materials Science Forum. ; 595-598, s. 289-297
  • Tidskriftsartikel (refereegranskat)abstract
    • Corrosion field tests have been carried out in the superheater region of a commercial waste-fired 75MW CFBC boiler using air cooled probes. Exposure time was 24 and 1000 hours. The effect of adding sulphur to the fuel on the corrosion of two high alloyed steels and a low alloyed steel was studied. The fuel consisted of 50% household waste and 50% industrial waste. The exposed samples were analyzed by ESEM/EDX and XRD. Metal loss was determined after 1000 hours. Both materials suffered significant corrosion in the absence of sulphur addition and the addition of sulphur to the fuel reduced corrosion significantly. The rapid corrosion of the high alloyed steel in the absence of sulphur addition is caused by the destruction of the chromium-containing protective oxide by formation of calcium chromate. Adding sulphur to the fuel inhibited chromate formation and increased the sulphate/chloride ratio in the deposit. Iron(II) chloride formed on the low alloyed steel regardless of whether sulphur was added or not.
  •  
4.
  • Froitzheim, Jan, 1981, et al. (författare)
  • Chromium evaporation of Coated and uncoated FE-22CR steels investigated by a novel denuder technique
  • 2009
  • Ingår i: 3rd European Fuel Cell Technology and Applications - Piero Lunghi Conference, EFC 2009; Rome; Italy; 15 December 2009 through 18 December 2009. - 9788882862114 ; , s. 77-78
  • Konferensbidrag (refereegranskat)abstract
    • The formation of volatile chromium species is a major problem concerning metallic interconnects for Solid Oxide Fuel Cells (SOFC). This problem is known and a number of routes, usually in the form of coatings, has been presented to overcome this problem. This paper investigates the influence of thin metallic films which can be applied by a low cost process. The measurements are carried out by a novel denuder technique where volatile chromium species are collected as sodium chromate. This technique allows the quantification of chromium evaporation in a time resolved manner. Coated and uncoated samples of ferritic steels developed for SOFC applications are investigated at 850°C in a N2-O2-H2O environment.
  •  
5.
  • Froitzheim, Jan, 1981, et al. (författare)
  • Cr evaporation of metallic interconnects: A novel method for quantification
  • 2009
  • Ingår i: ECS Transactions. - : The Electrochemical Society. - 1938-5862 .- 1938-6737. - 9781566777391 ; 25:2 PART 2, s. 1423-1428
  • Konferensbidrag (refereegranskat)abstract
    • Chromium evaporation from metallic interconnects in SOFCs is commonly poisoning the cathode of SOFCs. To reduce chromium evaporation, rather thick coatings have been deposited using various coating techniques. In this study, a 22% Cr ferritic steel has been coated with thin films (
  •  
6.
  • Froitzheim, Jan, 1981, et al. (författare)
  • Investigation of Chromium Volatilization from FeCr Interconnects by a Denuder Technique
  • 2010
  • Ingår i: Journal of the Electrochemical Society. - : The Electrochemical Society. - 1945-7111 .- 0013-4651. ; 157:9, s. B1295-B1300
  • Tidskriftsartikel (refereegranskat)abstract
    • A technique is presented for accurate and time-resolved quantification of chromium volatilization from alloys at high temperature. A denuder tube which is coated with Na2CO3 is placed downstream of the samples. CrO2(OH)(2) that evaporated from the samples is collected on the denuder and converted to the thermally stable Na2CrO4. The chromate is then dissolved in water and determined quantitatively. Three commercially available ferritic 22% Cr steels intended for use as solid oxide fuel cell interconnect materials (Sanergy HT, Crofer 22 APU, and ZMG 232) have been investigated with respect to chromium volatilization and oxidation rate. The effect on chromium volatilization of a submicrometer cobalt coating on the steel surface is reported. Comparisons are made with a conventional thick ceramic coating. The experiments are carried out at 850 degrees C in N-2 - 20% O-2 - 3% H2O atmosphere. The submicrometer Co coatings proved to be very efficient, reducing Cr volatilization by 1 order of magnitude. Microscopic studies show that both uncoated steel and steel coated with a submicrometer cobalt film develop two-layered oxide scales with the bottom part consisting of a Cr-rich corundum-type oxide. The uncoated samples develop a top layer consisting of (Cr, Mn)(3)O-4 oxide, whereas the Co-coated samples exhibit a top layer consisting of Co-rich spinel oxide. (C) 2010 The Electrochemical Society. [DOI: 10.1149/1.3462987] All rights reserved.
  •  
7.
  • Herstad-Svärd, S., et al. (författare)
  • Ramprogram – Åtgärder för samtidig minimering av alkalirelaterade driftproblem, Etapp 2
  • 2007
  • Rapport (övrigt vetenskapligt/konstnärligt)abstract
    • Combustion of an increasing amount of biofuel and waste woods has resulted in certainenvironmental advantages, including decreased emissions of fossil CO2, SO2 andmetals. On the other hand, a number of chloride and alkali related operational problemshave occurred which are related to combustion of these fuels.Alkali related operational problems have been studied in a project consisting of twoparts. The overall scope has been to characterise the operational problems and to studymeasures to minimise them. The first part was reported in Värmeforsk report 997 wherethe results were summarised in a table of different measures. In part two, additionalmeasures have been included in the test plan and initial corrosion has been studiedlinked to the different measures. The tests have also in part two been carried out at the12 MW CFB boiler at Chalmers. The effect of the selected measures has beeninvestigated concerning both deposit formation and bed agglomeration, and at the sametime emissions and other operational conditions were characterised.The second part of the project has among other things focused on:• To investigate measures which decrease the content of alkali and chloride in thedeposits, and consequently decrease the risk for corrosion (by investigating theinitial corrosion). Focus was also on trying to explain favourable effects.• To investigate if it is possible to combine a rather low dosage of kaolin and injectionof ammonium sulphate. This was done in order to reduce both bed agglomerationand problems from deposits during combustion of fuels rich in chlorine.• To investigate if co-combustion with sewage sludge, de-inking sludge or peat withhigh ash content, could give similar advantages as conventional additives.• Investigate if ash from PFBC is possible to use as an alternative bed material.By comparing the different measures in part two, it could be concluded that cocombustionof sewage sludge gave the best overall effect. The judgement was based onthe effects concerning bed agglomeration, level of alkali chloride in the flue gas,deposits and initial corrosion. Simultaneous addition of kaolin and ammonia sulphatealso had a favourable impact both in the bed and on the alkali chlorides in the gas phase.Dosage of kaolin did not reduce the effect of injected ammonium sulphate. Cocombustionof peat could also be a very attractive alternative, but it is critical to select asuitable peat type. It is of special concern to avoid peat with a high content of calcium,since it can increase the level of alkali chlorides by reacting with available sulphur.Change of bed material to ash from PFBC can decrease problems with bedagglomeration, but there is a risk of increased deposit formation and corrosion. A boileroperated with high steam data should consequently combine the change of bed materialwith injection of ammonium sulphate or another source of sulphur.Co-combustion of de-inking sludge from pulp and paper production can reduceproblems with bed agglomeration. There is, however, an increased chance of corrosiondue to the high content of calcium. Injection of sulphates may improve the situationconcerning corrosion. The results also showed that low potassium chlorine content in the flue gas decreasesthe risk of corrosion. Increased amount of potassium chlorine content in the flue gaswill not necessary give a high amount of chlorine content in the deposits if there is sulphur in the system.Key words: agglomeration, deposits, corrosion, alkali, kaolin, ammonium sulphate,sludge
  •  
8.
  •  
9.
  • Karlsson, Sofia, 1982, et al. (författare)
  • A Laboratory Study of the in Situ Sulfation of Alkali Chloride Rich Deposits: Corrosion Perspective
  • 2016
  • Ingår i: Energy & Fuels. - : American Chemical Society (ACS). - 1520-5029 .- 0887-0624. ; 30:9, s. 7256-7267
  • Tidskriftsartikel (refereegranskat)abstract
    • The initial corrosive effect of small (1.35 mu mol/cm(2)) and large (13.5 mu mol/cm(2)) amounts of KCl on 304L has been investigated. The investigations were performed in both the absence and presence of 300 ppm of SO2 at 600 degrees C. The results showed that in the absence of SO2 KCl accelerates the rate of corrosion by means of two types of corrosion attack: a general attack and a steel grain boundary attack. The general attack has been proved to be initiated by K2CrO4 formation. Meanwhile, the steel grain boundary attack is suggested to be accelerated by HCl released due to the chromate formation which increased with higher amounts of KCl. The presence of KCl and SO2 resulted in the simultaneous formation of K2SO4 and K2CrO4. The chromate formation resulted in a general corrosion attack. However, the oxide growth was significantly reduced due to the very fast sulfation reaction. In contrast, the steel grain boundary attack increased in the presence of SO2. It is suggested that the attack is accelerated by HCl released from the sulfation reaction and by sulfidation of the steel grain boundaries.
  •  
10.
  • Larsson, Erik, 1983, et al. (författare)
  • A Comparative Study of the Initial Corrosion of KCl and PbCl2 on a Low-Alloyed Steel
  • 2017
  • Ingår i: Oxidation of Metals. - : Springer Science and Business Media LLC. - 1573-4889 .- 0030-770X. ; 87:5-6, s. 779-787
  • Tidskriftsartikel (refereegranskat)abstract
    • Heat exchange surfaces in biomass- and waste-fired boilers are exposed to corrosive species due to the considerable amounts of alkali chlorides and PbCl2 which are released during combustion. The corrosivity of alkali chlorides toward superheater alloys exposed at high temperature has been studied extensively. However, at lower material temperatures, i.e., at waterwall conditions, considerably less research has been performed. In order to investigate the effect of small amounts of KCl and PbCl2 during the initial stages of the corrosion attack, a Fe–2.25Cr–1Mo steel was exposed for 24 h in an atmospheres consisting of O2 + H2O + N2 at 400 °C. Both KCl and PbCl2 resulted in an increased corrosion rate compared to the reference. The aim of the present paper is to investigate the influence of KCl and PbCl2 on the initial oxidation of a Fe–2.25Cr–1Mo steel. The work involves a detailed microstructural investigation as well as thermodynamic equilibrium calculations.
  •  
Skapa referenser, mejla, bekava och länka
  • Resultat 1-10 av 384
Typ av publikation
tidskriftsartikel (230)
konferensbidrag (109)
rapport (17)
bokkapitel (11)
annan publikation (6)
forskningsöversikt (6)
visa fler...
doktorsavhandling (2)
licentiatavhandling (2)
bok (1)
visa färre...
Typ av innehåll
refereegranskat (335)
övrigt vetenskapligt/konstnärligt (49)
Författare/redaktör
Jones, G. (21)
Price, D. (21)
Morris, J. (21)
Bowden, M. (21)
Silva, C. (21)
Duran, I (21)
visa fler...
Mayer, M. (21)
Lopez, J. M. (21)
Ambrosino, G (21)
Amosov, V (21)
Ariola, M (21)
Ash, A (21)
Avotina, L (21)
Baciero, A (21)
Balboa, I (21)
Balshaw, N (21)
Barnsley, R (21)
Batistoni, P (21)
Blanchard, P (21)
Boboc, A (21)
Bolzonella, T (21)
Braic, V (21)
Brett, A (21)
Brezinsek, S (21)
Buratti, P (21)
Carman, P (21)
Carralero, D (21)
Carvalho, I (21)
Carvalho, P (21)
Chernyshova, M (21)
Ciric, D (21)
Coelho, R (21)
Coffey, I (21)
Collins, S (21)
Coombs, D (21)
Corrigan, G (21)
Craciunescu, T (21)
Cramp, S (21)
Croci, G (21)
Crombe, K (21)
Cruz, N (21)
Cseh, G (21)
Curuia, M (21)
Delabie, E (21)
Dittmar, T (21)
Dux, R (21)
Fasoli, A (21)
Fischer, U (21)
Flanagan, J (21)
Formisano, A (21)
visa färre...
Lärosäte
Göteborgs universitet (29)
Kungliga Tekniska Högskolan (26)
Uppsala universitet (25)
Högskolan Väst (6)
RISE (6)
visa fler...
Jönköping University (5)
Stockholms universitet (4)
Högskolan Dalarna (4)
Lunds universitet (3)
Umeå universitet (2)
Luleå tekniska universitet (1)
Högskolan i Halmstad (1)
Högskolan i Borås (1)
Karolinska Institutet (1)
visa färre...
Språk
Engelska (378)
Svenska (6)
Forskningsämne (UKÄ/SCB)
Teknik (237)
Naturvetenskap (223)
Samhällsvetenskap (10)
Medicin och hälsovetenskap (7)
Humaniora (2)

År

Kungliga biblioteket hanterar dina personuppgifter i enlighet med EU:s dataskyddsförordning (2018), GDPR. Läs mer om hur det funkar här.
Så här hanterar KB dina uppgifter vid användning av denna tjänst.

 
pil uppåt Stäng

Kopiera och spara länken för att återkomma till aktuell vy