SwePub
Sök i SwePub databas

  Utökad sökning

Träfflista för sökning "WFRF:(Svensson Erik) srt2:(2000-2019);pers:(Hellström Kristina M 1971)"

Sökning: WFRF:(Svensson Erik) > (2000-2019) > Hellström Kristina M 1971

  • Resultat 1-10 av 17
Sortera/gruppera träfflistan
   
NumreringReferensOmslagsbildHitta
1.
  • Larsson, Erik, 1983, et al. (författare)
  • A Comparative Study of the Initial Corrosion of KCl and PbCl2 on a Low-Alloyed Steel
  • 2017
  • Ingår i: Oxidation of Metals. - : Springer Science and Business Media LLC. - 1573-4889 .- 0030-770X. ; 87:5-6, s. 779-787
  • Tidskriftsartikel (refereegranskat)abstract
    • Heat exchange surfaces in biomass- and waste-fired boilers are exposed to corrosive species due to the considerable amounts of alkali chlorides and PbCl2 which are released during combustion. The corrosivity of alkali chlorides toward superheater alloys exposed at high temperature has been studied extensively. However, at lower material temperatures, i.e., at waterwall conditions, considerably less research has been performed. In order to investigate the effect of small amounts of KCl and PbCl2 during the initial stages of the corrosion attack, a Fe–2.25Cr–1Mo steel was exposed for 24 h in an atmospheres consisting of O2 + H2O + N2 at 400 °C. Both KCl and PbCl2 resulted in an increased corrosion rate compared to the reference. The aim of the present paper is to investigate the influence of KCl and PbCl2 on the initial oxidation of a Fe–2.25Cr–1Mo steel. The work involves a detailed microstructural investigation as well as thermodynamic equilibrium calculations.
  •  
2.
  • Canovic, Sead, 1979, et al. (författare)
  • Microstructural Investigation of the Initial Oxidation of the FeCrAlRE Alloy Kanthal AF in Dry and Wet O-2 at 600 and 800 degrees C
  • 2010
  • Ingår i: Journal of the Electrochemical Society. - : The Electrochemical Society. - 1945-7111 .- 0013-4651. ; 157:6, s. C223-C230
  • Tidskriftsartikel (refereegranskat)abstract
    • The FeCrAlRE (where RE is reactive element) alloy Kanthal AF was exposed isothermally at 600 and 800 degrees C for 72 h in dry O-2 and in O-2 with 10 vol % H2O. The mass gains were 3-5 times higher at the higher temperature. The presence of water vapor increased the oxidation rate at 800 degrees C, while no significant effect was observed at 600 degrees C. A thin two-layered oxide formed at 600 degrees C: an outer (Fe, Cr)(2)O-3 corundum-type oxide, containing some Al, and an inner, probably amorphous, Al-rich oxide. At 800 degrees C a two-layered oxide formed in both environments. The inner layer consisted of inward grown alpha-Al2O3. In dry O-2 the originally formed outward grown gamma-Al2O3 had transformed to alpha-Al2O3 after 72 h. Water vapor stabilized the outward grown gamma-Al2O3 and hence no transformation occurred after 72 h in humid environment. RE-rich oxide particles with varying composition (Y, Zr, and Ti) were distributed in the base oxide at both temperatures and in both environments. The RE-rich particles were separated from the alloy substrate by a layer of Al-rich oxide. At 800 degrees C the Y-rich RE particles were surrounded by thick oxide patches in both dry and humid O-2.
  •  
3.
  • Engkvist, Josefin, 1972, et al. (författare)
  • Alumina scale formation on a powder metallurgical FeCrAl alloy (Kanthal APMT) at 900-1100°C in dry O2 and in O2 + H2O
  • 2010
  • Ingår i: Oxidation of Metals. - : Springer Science and Business Media LLC. - 1573-4889 .- 0030-770X. ; 73:1, s. 233-253
  • Tidskriftsartikel (refereegranskat)abstract
    • A Rapidly Solidified Powder (RSP) metallurgical FeCrAl alloy, Kanthal APMT, was exposed in dry and humid O-2 for 72 h at 900-1,100 A degrees C. The formed oxide scales were characterized using gravimetry in combination with advanced analysis techniques (SEM, EDX, TEM, XRD, AES and SIMS). The oxide scales were at all exposures composed of two-layered alpha-Al2O3 scales exhibiting a top layer of equiaxed grains and a bottom layer containing elongated grains. A Cr-rich zone, originating in the native oxide present before exposure, separated these two layers. The top alpha-Al2O3 layer is suggested to have formed by transformation of outwardly grown metastable alumina, while the inward-grown bottom alpha-Al2O3 layer had incorporated small Zr-, Hf- and Ti-rich oxide particles present in the alloy matrix. The scale also contained larger Y-rich oxide particles. Furthermore, in the temperature range studied, the presence of water vapour accelerated alloy oxidation somewhat and affected scale morphology.
  •  
4.
  • Hall, Josefin, 1972, et al. (författare)
  • The Initial Oxide Scale Development on a Model FeNiCrAl Alloy at 900 degrees C in Dry and Humid Atmosphere: A Detailed Investigation
  • 2014
  • Ingår i: Oxidation of Metals. - : Springer Science and Business Media LLC. - 1573-4889 .- 0030-770X. ; 82:3-4, s. 225-247
  • Tidskriftsartikel (refereegranskat)abstract
    • The investigated alumina forming FeNiCrAl model alloy shows protective oxidation behavior in dry and humid environment at 900 A degrees C. Hence, this type of alloy may replace conventional chromia forming austenitic alloys in aggressive oxidizing/reducing environments. A detailed investigation of the oxide scale development reveals a complex initial scale development. Firstly, at alloy grain boundaries, a thin Al rich oxide forms which is replaced by transient alumina platelets in dry and equiaxed alpha-Al2O3 crystallites in humid atmosphere. The scale at alloy grain centers develops via a layered scale of external chromia:Fe/Ni metal inclusions:internal alumina to a layered external spinel:internal alumina scale in dry atmosphere. In humid condition an additional oxide feature appears on the center of large alloy grains i.e. thick oxide protrusions. Despite the initially different phase compositions a continuous protective alpha-Al2O3 scale forms both atmospheres.
  •  
5.
  • Hellström, Kristina M, 1971, et al. (författare)
  • Mitigation of Fireside Corrosion in Power Plants: The Combined Effect of Sulfur Dioxide and Potassium Chloride on the Corrosion of a FeCrAl Alloy
  • 2014
  • Ingår i: Energy & Fuels. - : American Chemical Society (ACS). - 0887-0624 .- 1520-5029. ; 28:9, s. 6116-6129
  • Tidskriftsartikel (refereegranskat)abstract
    • The corrosion behavior of a FeCrAl alloy (Kanthal APMT) was investigated in 5% O-2 with 40% H2O plus 300 ppm of SO2 at 600 degrees C in the presence or absence of KCl, and the results were also compared to exposures performed without SO2 and KCl. The influence of preoxidation was also examined. The kinetics was followed using mass gain measurements, and the formed corrosion products were examined using XRD, SEM/EDX, AES, IC, and SIMS. The oxidation rate of Kanthal APMT was very low in O-2/N-2/H2O + 300 ppm of SO2, and the outward alumina growth appeared to be suppressed. Interestingly, no sulfur was detected at the scale/metal interface. KCl strongly accelerated the corrosion of Kanthal APMT in O-2/H2O/N-2 at 600 degrees C, forming K2CrO4 and gaseous HCl. Chromate formation depletes the protective scale in Cr, triggering the formation of a fast growing iron-rich scale. Adding SO2 suppressed the corrosion due to the conversion of the corrosive KCl to the stable K2SO4. If any K2CrO4 was formed on the surface of the material initially, it was also rapidly converted to K2SO4. Preoxidation of Kanthal APMT had a strong beneficial effect on the subsequent exposure at 600 degrees C in the presence of KCl and SO2, resulting in the formation of K2SO4 and the evaporation of HCl and KCl. In summary, the alumina-forming FeCrAl material Kanthal APMT is not completely inert to KCl in an oxidizing SO2-containing atmosphere at 600 degrees C. However, the corrosion rate is significantly lower than that of the commonly used chromia-forming alloy, 304L. Preoxidation decreases the corrosion rate even further, making Kanthal APMT a promising candidate material for combustion plant components, particularly from a corrosion point of view.
  •  
6.
  • Hellström, Kristina M, 1971, et al. (författare)
  • Oxidation behaviour of a (Mo, W)Si2-based composite in dry and wet oxygen atmospheres in the temperature range 350–950◦C
  • 2009
  • Ingår i: Journal of the European Ceramic Society. - : Elsevier BV. - 1873-619X .- 0955-2219. ; 29:10, s. 2105-2118
  • Tidskriftsartikel (refereegranskat)abstract
    • The oxidation of a (Mo, W)Si2-based composite was investigated in the temperature range (350–950 °C). The influence of temperature and water vapour on the oxidation was examined. The kinetics was studied using a thermobalance whereas the morphology and composition of the oxides were examined using X-ray diffractometer (XRD), scanning electron microscope (SEM), transmission electron microscope (TEM) and energy dispersive X-ray (EDX). Focused ion beam (FIB) milling was performed on some of the oxide scales which allowed us to look at a non-mechanically disturbed scale/oxide in cross-section. Rapid oxidation was found to occur in the 550–750 °C temperature range. The mass gains were significantly larger in O2 than in O2 + 10%H2O. The different mass changes in the two exposure atmospheres were attributed to the higher vapour pressure of the volatile MoO2(OH)2 and WO2(OH)2 species in O2 + 10%H2O than that of (MoO3)3 and (WO3)3 in dry O2. The peak mass gain was found to occur at a temperature of about 750 °C in O2 and 650 °C in O2 + 10%H2O. At temperatures above 850 °C, especially when water vapour is present, the removal of Mo and W from the oxide scales is rapid enough to allow partial healing of the silica, causing the oxidation rate to drop. At 950 °C in O2 + 10%H2O, a protective SiO2 scale could be re-established quickly and maintained, causing the oxidation to essentially cease.
  •  
7.
  • Hellström, Kristina M, 1971, et al. (författare)
  • Oxidation of a Dispersion-Strengthened Powder Metallurgical FeCrAl Alloy in the Presence of O2 at 1,100°C: The Influence of Water Vapour
  • 2015
  • Ingår i: Oxidation of Metals. - : Springer Science and Business Media LLC. - 1573-4889 .- 0030-770X. ; 83:5-6, s. 533-558
  • Tidskriftsartikel (refereegranskat)abstract
    • The oxidation behaviour of the FeCrAl alloy Kanthal(A (R)) APMT in O-2 + N-2 and O-2 + N-2 + H2O environments at 1,100 A degrees C was investigated using thermogravimetry and detailed analyses of the scale morphology with SEM/EDX and STEM/EDX. Wrought FeCrAl alloy Kanthal(A (R)) AF was used as a reference. Exposure time was up to 168 h. Water vapour influenced the early oxide growth kinetics. This effect is explained in terms of water acting as an oxidant, simultaneously with O-2. During later stages of the exposures, H2O had no effect on the kinetics of oxidation.
  •  
8.
  • Hellström, Kristina M, 1971, et al. (författare)
  • The Oxide Scales Formed on a Dispersion-Strengthened Powder Metallurgical FeCrAl Alloy at 900 A degrees C in O-2 and in O-2 + H2O
  • 2015
  • Ingår i: Oxidation of Metals. - : Springer Science and Business Media LLC. - 1573-4889 .- 0030-770X. ; 84:1-2, s. 1-19
  • Tidskriftsartikel (refereegranskat)abstract
    • Early oxide scale growth on an oxide dispersion strengthened rapidly solidified powder FeCrAl material, Kanthal(A (R)) APMT, was investigated at 900 A degrees C in an O-2 + N-2 and an O-2 + H2O + N-2 environment for up to 168 h. Gravimetry was used to follow oxide growth and the oxide scale was examined with XRD. Scale morphology was investigated in detail with SEM/EDX, TEM/EDX/CBED. The alloy rapidly formed a protective two-layered alpha-alumina scale containing oxide nodules. Between the top and bottom alumina layers there was a zone containing chromia-rich particles 5-20 nm in diameter, corresponding to the original sample surface. The alumina scale mainly grew inward after 1 h of oxidation. Alumina scale growth at 900 A degrees C was initially somewhat faster in an O-2 + H2O + N-2 environment than in an O-2 + N-2 environment.
  •  
9.
  • Ingemarsson, Linda, 1972, et al. (författare)
  • Oxidation behavior at 300–1000C of a (Mo,W)Si2-based composite containing boride
  • 2010
  • Ingår i: Intermetallics. - : Elsevier BV. - 0966-9795. ; 18:1, s. 77-86
  • Tidskriftsartikel (refereegranskat)abstract
    • The oxidation behavior of a (Mo,W)Si2 composite with boride addition was examined at 300–1000C for24 h in dry O2. The oxidation kinetics was studied using a thermobalance, and the oxide scales wereanalyzed using a combination of electron microscopy (SEM/EDX, FIB, BIB) and XRD. Accelerated oxidationwas found to occur between 500C and 675C, with a peak mass gain at 625C. The rapid oxidation isattributed to the vaporization of molybdenum oxide that leaves a porous and poorly protective silicalayer behind. At higher temperature (700–1000C) a protective scale forms, consisting of a dense SiO2/B2O3 glass.
  •  
10.
  • Ingemarsson, Linda, 1972, et al. (författare)
  • Oxidation behavior of a Mo (Si, Al)(2)-based composite at 300-1000 degrees C
  • 2010
  • Ingår i: Intermetallics. - : Elsevier BV. - 0966-9795 .- 1879-0216. ; 18:4, s. 633-640
  • Tidskriftsartikel (refereegranskat)abstract
    • The oxidation behavior of a Mo (Si,Al)(2)-based composite of Mo(Si,Al)(2), Al2O3 and Mo-5(Si,Al)(3) (Kanthal Super ER) in synthetic air was investigated. The samples were oxidized isothermally for up to 72 h at 300-1000 degrees C using a thermobalance. The microstructure was analyzed by X-ray diffraction (XRD), Scanning Electron Microscopy (SEM) and Auger Electron Spectroscopy (AES) depth profiling. Broad ion beam milling (BIB) was used to prepare cross-sections. Oxidation behavior depended strongly on the composition of the substrate which consisted of a Mo(Si,Al)(2) matrix and the minority phases Mo-5(Si,Al)(3) and Al2O3. At 300-500 degrees C the mass gains were small with parabolic kinetics, oxidation resulting in a mixture of oxides that reflects the substrate composition. At 600 and 700 degrees C the oxide scale is thin and protective and depleted in molybdenum, a mass loss occurring due to MoO3 vaporization. At 1000 degrees C a protective alpha-alumina scale forms.
  •  
Skapa referenser, mejla, bekava och länka
  • Resultat 1-10 av 17

Kungliga biblioteket hanterar dina personuppgifter i enlighet med EU:s dataskyddsförordning (2018), GDPR. Läs mer om hur det funkar här.
Så här hanterar KB dina uppgifter vid användning av denna tjänst.

 
pil uppåt Stäng

Kopiera och spara länken för att återkomma till aktuell vy