| 1. |
|
|
| 2. |
- Lyu, Yezhe, 1987-, et al.
(författare)
-
Friction, wear and airborne particle emission from Cu-free brake materials
- 2020
-
Ingår i: Tribology International. - : Elsevier. - 0301-679X .- 1879-2464. ; 141
-
Tidskriftsartikel (refereegranskat)abstract
- Cu is required to be abated in brake pads due to its toxicity. There are on the market several Cu-free brake pads. These Cu-free brake pads are only evaluated regarding their friction and wear performance, whereas, their airborne particle emissions are not considered. A pin-on-disc tribometer is used to evaluate the friction, wear and airborne particle emission from two Cu-free commercial brake pads used in the Europe. Moreover, a commercial brake pad containing Cu is evaluated as a reference. The results indicate that Cu-free brake pads yield comparable coefficient of friction as the Cu-contained brake pad. All three brake materials result in similar wear to the mating brake rotor. Cu-free brake pads generate more airborne particles than Cu-contained brake pad.
|
|
| 3. |
- Olofsson, Ulf, 1962-, et al.
(författare)
-
Laser Cladding Treatment for Refurbishing Disc Brake Rotors : Environmental and Tribological Analysis
- 2021
-
Ingår i: Tribology letters. - New York : Springer Nature. - 1023-8883 .- 1573-2711. ; 69:2
-
Tidskriftsartikel (refereegranskat)abstract
- In this study, grey cast iron disc brake rotors are refurbished by adding a surface layer through laser cladding. Current methods to deal with replaced rotors mainly include remelting, with a minority fraction disposed in landfill. Both approaches result in a huge waste of resources and an increase in CO2 footprint. From a sustainable point of view, this study aims to evaluate the feasibility of refurbishing brake rotors by a combined environmental and tribological performance approach. A streamlined life cycle assessment is conducted to compare the environmental impacts between producing virgin grey cast iron brake rotors and refurbishing replaced brake rotors by laser cladding. It turns out that the energy consumption and CO2 footprint of the laser cladding refurbished brake rotors are 80% and 90% less than the virgin brake rotors. The results show that the refurbished brake rotor yields higher friction compared to the original cast iron utilizing the same pad material. The wear and particle emissions of the disc brake contact are in this study higher for the laser-cladded one compared to the original cast iron one.
|
|
| 4. |
- Perricone, Guido, 1973-, et al.
(författare)
-
A concept for reducing PM10 emissions for car brakes by 50%
- 2018
-
Ingår i: Wear. - : Elsevier. - 0043-1648 .- 1873-2577. ; 396, s. 135-145
-
Tidskriftsartikel (refereegranskat)abstract
- With regard to airborne particles with an aerodynamic diameter of less than 10 mu m (PM10), in countries in the European Union, the mass of brake emissions equals approximately 8-27% of the total traffic-related emissions. Using a research methodology combining tests at different scale levels with contact mechanics simulations and PM10 chemical characterization, the REBRAKE EU-financed project had the following aims: i) to demonstrate the possibility of reducing the PM10 fraction of the airborne particulate from brake wear by 50 wt%; ii) to enhance the general understanding on the physical and chemical phenomena underlying the brake wear process. The results achieved so far indicate that it is possible to design a disc brake system for a European standard car affording at least a 32 wt% PM10 emission reduction using a standard European pad and a heat-treated rotor. A further reduction to 65 wt% PM10 emission could be achieved with NAO pad material and the same heat-treated disc.
|
|
| 5. |
- Wahlström, Jens, et al.
(författare)
-
A study of the effect of brake pad scorching on tribology and airborne particle emissions
- 2020
-
Ingår i: Atmosphere. - 2073-4433. ; 11:5
-
Tidskriftsartikel (refereegranskat)abstract
- Non-exhaust wear emissions from disc brakes affect the air quality in cities throughout the world. These emissions come from the wear of the contact surfaces of both the pads and disc. The tribological and emissions performance of disc brakes strongly depend on the contact surface characteristics of the pads and discs. The surfaces of conventional pads are scorched by heating it to several hundred degrees to make the resin carbonize down to a few millimetres deep into the pad. This is done to have a shorter run-in period for new pads. It is not known how scorching will affect the amount of airborne particle emissions. Therefore, the aim of the present study is to investigate how pad scorching influence the airborne particle emissions. This is done by comparing the pin-on-disc tribometer and inertia dyno bench emission results from a Cu-free friction material run against a grey cast iron disc. Three types of modified friction material surfaces have been tested: scorched, extra-scorched and rectified. The results show that the level of scorching strongly affects the airborne particle emissions in the initial phase of the tests. Even if the scorched layer is removed (rectified) before testing, it seems like it still has a measurable influence on the airborne particle emissions. The results from the tribometer tests are qualitatively in line with the inertia dyno bench test for about the first forty brake events; thereafter, the airborne particle emissions are higher for the scorched pads. It can be concluded that it seems that the level of scorching has an adverse influence on both the tribological performance and level of particle emissions.
|
|
| 6. |
- Wahlström, Jens, PhD/Docent, 1979-, et al.
(författare)
-
A Study of the Effect of Brake Pad Scorching on Tribology and Airborne Particle Emissions
- 2020
-
Ingår i: Atmosphere. - : MDPI. - 2073-4433 .- 2073-4433. ; 11:5
-
Tidskriftsartikel (refereegranskat)abstract
- Non-exhaust wear emissions from disc brakes affect the air quality in cities throughout the world. These emissions come from the wear of the contact surfaces of both the pads and disc. The tribological and emissions performance of disc brakes strongly depend on the contact surface characteristics of the pads and discs. The surfaces of conventional pads are scorched by heating it to several hundred degrees to make the resin carbonize down to a few millimetres deep into the pad. This is done to have a shorter run-in period for new pads. It is not known how scorching will affect the amount of airborne particle emissions. Therefore, the aim of the present study is to investigate how pad scorching influence the airborne particle emissions. This is done by comparing the pin-on-disc tribometer and inertia dyno bench emission results from a Cu-free friction material run against a grey cast iron disc. Three types of modified friction material surfaces have been tested: scorched, extra-scorched and rectified. The results show that the level of scorching strongly affects the airborne particle emissions in the initial phase of the tests. Even if the scorched layer is removed (rectified) before testing, it seems like it still has a measurable influence on the airborne particle emissions. The results from the tribometer tests are qualitatively in line with the inertia dyno bench test for about the first forty brake events; thereafter, the airborne particle emissions are higher for the scorched pads. It can be concluded that it seems that the level of scorching has an adverse influence on both the tribological performance and level of particle emissions.
|
|
