| 1. |
- Asfaw, Habtom Desta, Dr. 1986-, et al.
(författare)
-
Facile synthesis of hard carbon microspheres from polyphenols for sodium-ion batteries : insight into local structure and interfacial kinetics
- 2020
-
Ingår i: Materials Today Energy. - : Elsevier BV. - 2468-6069. ; 18
-
Tidskriftsartikel (refereegranskat)abstract
- Hard carbons are the most promising negative active materials for sodium ion storage. In this work, a simple synthesis approach is proposed to produce hard carbon microspheres (CMSs) (with a mean diameter of ~1.3 μm) from resorcinol-formaldehyde precursors produced via acid-catalyzed polycondensation reaction. Samples prepared at 1200, 1400, and 1500 oC showed different electrochemical behavior in terms of reversible capacity, initial coulombic efficiency (iCE), and the mechanism of sodium ion storage. The specific capacity contributions from the flat voltage profile (<0.1 V) and the sloping voltage region (0.1–1 V) showed strong correlation to the local structure (and carbonization temperature) determined by the interlayer spacing (d002) and the Raman ID/IG ratio of the hard carbons (HCs) and the rate of cycling. Electrochemical tests indicated that the HC synthesized at 1500 oC performed best with an iCE of 85–89% and a reversible capacity of 300–340 mAh g−1 at 10 mA g−1, with the majority of charge stored below 0.1 V. The d002 and the ID/IG ratio for the sample were ~3.7 Å and ~1.27, respectively, parameters indicative of the ideal local structure in HCs required for optimum performance in sodium-ion cells. In addition, galvanostatic tests on three-electrode half-cells cells revealed that sodium metal plating occurred as cycling rates were increased beyond 80 mA g−1 leading to considerably high capacity and poor coulombic efficiency, a point that must be considered in full-cell batteries. Pairing the hard CMS electrodes with Prussian white positive electrode, a proof-of-concept cell could provide a specific capacity of almost 100 mAh g−1 maintained for more than 50 cycles with a nominal voltage of 3 V.
|
|
| 2. |
- Gond, Ritambhara, et al.
(författare)
-
A Lignosulfonate Binder for Hard Carbon Anodes in Sodium-Ion Batteries : A Comparative Study
- 2021
-
Ingår i: ACS Sustainable Chemistry and Engineering. - : American Chemical Society. - 2168-0485. ; 9:37, s. 12708-
-
Tidskriftsartikel (refereegranskat)abstract
- An important factor in the development of sodium-ion batteries (SIBs) is the use of cheap and sustainable materials. Sodium lignosulfonate, a lignin derivative, is demonstrated here as an attractive, "green", water-soluble, and potentially cost-effective binder for use in hard carbon anodes for SIBs. A comparison of its battery cycling performance is made against other binders including sodium carboxymethyl cellulose and lignin, obtained from the kraft process, as well as sodium alginate, derived from algae. Apart from lignin, which requires processing in N-methyl-2-pyrrolidone, the other three binders are water-soluble. Lignosulfonate shows comparable or better performance, with high capacity retention and stability, when using 1 M NaPF6 in propylene carbonate or ethylene carbonate:diethyl carbonate electrolytes for both half- and full-cells (against a Prussian white cathode). Further improvements are observed when including styrene-butadiene rubber as a co-binder. X-ray photoelectron spectroscopy demonstrates similar solid electrolyte interphase compositions after the initial sodium insertion for both lignosulfonate and carboxymethyl cellulose binders. However, after subsequent cycling, the surface layer composition and thickness are found to be dependent on the binder. For the lignosulfonate-based electrode, the layer appears thicker but comprises a smaller fraction of carbon-oxygen species. © 2021 The Authors.
|
|
| 3. |
- Hakim, Charifa, et al.
(författare)
-
Development of P2 or P2/P3 cathode materials for sodium-ion batteries by controlling the Ni and Mn contents in Na0.7CoxMnyNizO2 layered oxide
- 2023
-
Ingår i: Electrochimica Acta. - : Elsevier. - 0013-4686 .- 1873-3859. ; 438
-
Tidskriftsartikel (refereegranskat)abstract
- Layered oxide cathode materials with the general formula NaxTMO2 (TM = transition metals) have shown promises as electrode materials for future large-scale sodium-ion batteries. However, several challenges including capacity degradation at high voltage, phase transitions as well as structural sensitivity to minor changes in the sodium and transition metal contents during the synthesis process have hampered their development. Herein, we report a systematic investigation of the impact of replacing cobalt by either manganese or nickel on the structural and electrochemical properties of Na0.7CoxMnyNizO2 (x + y + z = 1) layered oxide materials using a variety of analysis and electrochemical techniques. Mixed phases of P2 and P3 cathode materials are obtained through a slight increase of the nickel content, while increasing the manganese content showed little effect on the P2-type structure. Increasing manganese content is shown to lead to lower discharge capacity but excellent capacity retention after 100 cycles, while nickel-rich electrodes exhibit higher discharge capacity approaching 120 mAh/g but poor rate capability performance.
|
|
| 4. |
- Hakim, Charifa, et al.
(författare)
-
P-doped Hard Carbon as Anode Material for Sodium-ion Batteries
- 2019
-
Ingår i: Proceedings of 2019 7th international renewable and sustainable energy conference (IRSEC). - : IEEE. - 9781728151526 ; , s. 754-756
-
Konferensbidrag (refereegranskat)abstract
- The P-doped hard carbon was synthesized using carboxymethyl cellulose and phosphoric acid as the carbon and phosphorus precursors, respectively. The X-ray photoelectron spectroscopy (XPS) analysis reveals that the doped phosphorus atoms can incorporate into the carbon framework and most of them are connecting with carbon atoms to form P-C bonds. When used as anodes in sodium ion batteries, the obtained un-doped and P-doped hard carbon show poor electrochemical performances. The results indicate further optimization of the synthesis process is required. However, this approach opens up new possibilities to improve electrochemical performance of hard carbon anodes.
|
|
| 5. |
- Jin, Yanghao, et al.
(författare)
-
From Waste Biomass to Hard Carbon Anodes : Predicting the Relationship between Biomass Processing Parameters and Performance of Hard Carbons in Sodium-Ion Batteries
- 2023
-
Ingår i: Processes. - : MDPI AG. - 2227-9717. ; 11:3
-
Forskningsöversikt (refereegranskat)abstract
- Sodium-ion batteries (SIBs) serve as the most promising next-generation commercial batteries besides lithium-ion batteries (LIBs). Hard carbon (HC) from renewable biomass resources is the most commonly used anode material in SIBs. In this contribution, we present a review of the latest progress in the conversion of waste biomass to HC materials, and highlight their application in SIBs. Specifically, the following topics are discussed in the review: (1) the mechanism of sodium-ion storage in HC, (2) the HC precursor's sources, (3) the processing methods and conditions of the HCs production, (4) the impact of the biomass types and carbonization temperature on the carbon structure, and (5) the effect of various carbon structures on electrochemical performance. Data from various publications have been analyzed to uncover the relationship between the processing conditions of biomass and the resulting structure of the final HC product, as well as its electrochemical performance. Our results indicate the existence of an ideal temperature range (around 1200 to 1400 degrees C) that enhances the formation of graphitic domains in the final HC anode and reduces the formation of open pores from the biomass precursor. This results in HC anodes with high storage capacity (>300 mAh/g) and high initial coulombic efficiency (ICE) (>80%).
|
|
| 6. |
- Shi, Ziyi, et al.
(författare)
-
Bio-based anode material production for lithium–ion batteries through catalytic graphitization of biochar : the deployment of hybrid catalysts
- 2024
-
Ingår i: Scientific Reports. - : Springer Nature. - 2045-2322. ; 14:1
-
Tidskriftsartikel (refereegranskat)abstract
- Producing sustainable anode materials for lithium-ion batteries (LIBs) through catalytic graphitization of renewable biomass has gained significant attention. However, the technology is in its early stages due to the bio-graphite's comparatively low electrochemical performance in LIBs. This study aims to develop a process for producing LIB anode materials using a hybrid catalyst to enhance battery performance, along with readily available market biochar as the raw material. Results indicate that a trimetallic hybrid catalyst (Ni, Fe, and Mn in a 1:1:1 ratio) is superior to single or bimetallic catalysts in converting biochar to bio-graphite. The bio-graphite produced under this catalyst exhibits an 89.28% degree of graphitization and a 73.95% conversion rate. High-resolution transmission electron microscopy (HRTEM) reveals the dissolution–precipitation mechanism involved in catalytic graphitization. Electrochemical performance evaluation showed that the trimetallic hybrid catalyst yielded bio-graphite with better electrochemical performances than those obtained through single or bimetallic hybrid catalysts, including a good reversible capacity of about 293 mAh g−1 at a current density of 20 mA/g and a stable cycle performance with a capacity retention of over 98% after 100 cycles. This study proves the synergistic efficacy of different metals in catalytic graphitization, impacting both graphite crystalline structure and electrochemical performance.
|
|
| 7. |
- Tesfamhret, Yonas, et al.
(författare)
-
Revealing capacity fading in Sb-based anodes using symmetric sodium-ion cells
- 2021
-
Ingår i: Journal of Physics. - : Institute of Physics Publishing (IOPP). - 2515-7639. ; 4:2
-
Tidskriftsartikel (refereegranskat)abstract
- The electrochemical performance of negative active materials employed in sodium-ion batteries is dependent on the amount of Na+ available in the test cells. As such, electrodes that exhibit long cycle-life and high coulombic efficiency (CE) in half-cells could suffer from fast capacity fading in full-cells as a result of unstable solid electrolyte interphase (SEI) and mechanical degradation leading to loss of active materials. In this work, the performance of Sb–graphite composite active materials prepared by extended ball-milling was evaluated in sodium half-cells and various types of symmetric cells (SCs). In half-cell tests, the composite electrodes provided specific capacities in the range 350–600 mAh g−1 at C/20 with initial CE of 82%. A stable capacity of 380 mAh g−1 was observed in the subsequent 100 cycles with the CE increasing to nearly 99%. However, self-discharge tests on half-cells and galvanostatic cycling of SCs revealed poor capacity retention as a result of parasitic reaction occurring through the SEI layer. Contrary to half-cells, the SCs revealed that Sb electrodes suffered from sharp capacity losses when a limited amount of Na+ ions was available in the cells. This is also characteristic of full-cells in which the sodium ions are supplied by the positive electrode.
|
|
