| 1. |
|
|
| 2. |
|
|
| 3. |
- Hellström, Stefan, 1978, et al.
(författare)
-
Synthesis and characterization of three small band gap conjugated polymers for solar cell applications
- 2010
-
Ingår i: Polymer Chemistry. - : Royal Society of Chemistry (RSC). - 1759-9954 .- 1759-9962. ; 1:8, s. 1272-1280
-
Tidskriftsartikel (refereegranskat)abstract
- We report on a new series of small band gap conjugated polymers utilizing donor-acceptor-donor substructures in the polymer backbone to broaden and extend the optical absorption to longer wavelengths. Three polymers were prepared by Suzuki polymerization, using the same donor-acceptor-donor segment but with different comonomers. The goal was to investigate how the optical and electronic properties of the polymers were influenced by the different comonomers. Electrochemical spectroscopy, using square-wave voltammetry, shows that increasing the electron-donating strength of the comonomer will raise the HOMO energy level of the polymer, resulting in a decreased band gap. This result is also manifested by comparing open-circuit voltages from the corresponding laboratory fabricated solar cells. The best performing photovoltaic cell, based on APFO-Green15/[60]PCBM (1 : 4 w/w), reached a J(sc) of 4.2 mA cm(-2), a V-oc of 0.73 V, and a FF of 0.54, giving a PCE of 1.7%.
|
|
| 4. |
|
|
| 5. |
- Lindgren, Lars Johan, 1977, et al.
(författare)
-
Blue light-emitting diodes based on novel polyfluorene copolymers
- 2007
-
Ingår i: Journal of Luminescence. ; 122-123, s. 610-613
-
Konferensbidrag (refereegranskat)abstract
- This study presents the synthesis and characterization of a series of fluorene-based conjugated copolymers, together with the prepn. and characterization of the corresponding light-emitting devices. The polymers consist of alkoxyphenyl-substituted fluorene units together with different amts. of a hole-transporting triphenylamine-substituted fluorene unit: 0%, 10%, 25% and 50%. All polymers (P0, P1, P2, and P3) show high photoluminescence efficiency (hPL) and light emission (both PL and EL) in the blue spectral region. Electrochem. studies show improved hole injection as the ratio of the triphenylamine-substituted segment is increased. The electroluminescence quantum efficiencies (EQEs) of the devices increase six times going from P0 to P1. Compared with P1, polymers P2 and P3 show lower efficiencies in devices. These findings indicate the presence of an optimal polymer compn., where balance between the charge-carrier mobilities has been reached. [on SciFinder (R)]
|
|
| 6. |
- Lindgren, Lars Johan, 1977, et al.
(författare)
-
Synthesis, Characterization, and Devices of a Series of Alternating Copolymers for Solar Cells
- 2009
-
Ingår i: CHEMISTRY OF MATERIALS. - : American Chemical Society (ACS). - 0897-4756 .- 1520-5002. ; 21:15, s. 3491-3502
-
Tidskriftsartikel (refereegranskat)abstract
- In this study we report the synthesis, characterization. and photovoltaic properties of a series of six Conjugated polymers based on donor-acceptor-donor (DAD) structure. The polymers are obtained via Suzuki polymerization of different alkoxy-substituted DAD monomers together with a substituted fluorene or phenylene monomer. Application of polymers as light-harvesting and electron-donating materials in solar cells, in conjunction with both [60]PCBM and [70]PCBM as acceptors, show power-conversion efficiencies (PCEs) up to 2.9%, values obtained without extensive optimization work. Furthermore, atomic force microscopy and field-effect transistor (FET) mobility measurements of acceptor-polymer mixtures show that differences in substitution on the polymers affect morphology, mobility, and device performance. Within the series of polymers, all showing similar optical absorption and redox behavior, substituents play an important role in phase separation on a micrometer scale, which in turn has a large impact on device performance. The phase-separation behavior is clearly seen in [70]PCBM devices where the best-performing devices are obtained using the polymers with short alkoxy groups or no substituents together with a high speed of spin coating during device preparation.
|
|
